Table of Contents
Advertisement
HDMI Settings
Some early HDMI equipment may not work properly with your
HDMI TV. Please try setting the Enable Content Type and
INSTAPORT™ options to Off. Adjusting these settings should
allow your early HDMI source to operate properly with your
television.
a
In the Preferences menu, press
Connection and press OK.
b
B
b
Press
or
to select HDMI Settings and press OK.
NOTE: HDMI Settings is grayed out on non-HDMI
inputs.
c
B
b
Press
or
to select an item and press
select a setting.
HDMI Settings
Enable Content Type
INSTAPORT
TM
RGB Range
• Enable Content Type: On
This feature is part of the HDMI standard.
When set to On, the TV will automatically adjust
settings according to the content type data sent
from the connected HDMI device.
• INSTAPORT™: On
This feature reduces the lag time when switching
HDMI sources.
• RGB Range: Auto
This feature adjusts RGB full range signal
automatically. When Limited is selected, RGB signal
is output in the range from 16 to 235. When Full is
selected, RGB signal is output in the range from 0 to
255.
NOTE:
• If your HDMI connection is capable of 1080p and/or your
television is capable of refresh rates greater than 50Hz or
supports Deep Colour, you will need a Category 2 cable.
Conventional HDMI/DVI cables may not work properly with
this mode.
• All of the above HDMI settings need proper HDMI source
devices.
If the HDMI source products do not support these features,
the television may not work properly by activating these
features.
Digital Audio Output
When connecting a surround sound amplifier to the digital audio
output (Sony/Philips Digital Interface Format [S/PDIF]), the
following options can be selected or adjusted.
a
In the Preferences menu, press
Connection and press OK.
b
B
b
or
to select AV
c
C
c
or
to
On
On
Auto
B
b
or
to select AV
91
CONTROLS AND FEATURES
B
b
Press
or
to select Digital Audio Output.
AV Connection
Input Labeling
PC/HDMI 3 Audio
Side Shared Audio
HDMI 3 Audio
HDMI Settings
Digital Audio Output
Press OK to display Digital Audio Output menu and
B
b
press
or
to select an option.
Audio Format:
C
c
Press
or
to select PCM or Auto.
PCM: This mode outputs PCM format to the digital
audio output socket.
Auto: This mode outputs Dolby Digital (if available)
or PCM to the digital audio output socket.
S
Dolby Digital
Dolby Digital
S
Dolby Digital Plus
S
MPEG
PCM
S
HE-AAC
Dolby Digital
Audio Delay:
C
c
Press
or
to select Auto or Manual.
Auto:
This mode automatically adjusts the audio
timing to meet the video timing.
NOTE: The time lag might be large between
the image and sound depending on the
connected equipment (amplifier etc.). In that
case, select Manual.
Manual:You can manually adjust the audio signal
timing to meet the video signal timing.
Delay Adjustment:
C
c
Press
or
to adjust the audio signal timing
(0 – 250ms) to meet the video signal timing.
NOTE:
• This feature is grayed out when Audio Delay is in
Auto.
• A time lag will occur when the video signal or audio
signal is changed. Adjust the timing accordingly.
• When adjusting the timing, turn down the volume
of the AV equipment used as far as possible.
Depending on the equipment, noise etc. may occur
when the signal is changed.
• Depending on the connected equipment (amplifier,
etc.), adjustment may not be possible.
• When the optical digital output setting (Auto
is changed, it may be necessary to adjust the timing
again.
• Do not use other than for audio output from the AV
amplifier, etc. (Malfunction may occur)
PC
EXT 2
Auto
Dolby Digital
t
PCM)
Advertisement
Table of Contents
