Sony PDW-1500 Operation Manual page 95

Changing the currently displayed menu
item
SG DATA SG DATA SG DATA SG DATA EDIT
ACCESS
ANA SDI ANA SDI ANA SDI ANA SDI INPUT
VITC
AE8/EBU AE8/EBU AE8/EBU AE8/EBU
i.LINK
dB OVER dB OVER dB OVER dB OVER
SDI
0 0 0 0
CMPST
NETWORK -12 -12 -12 -12
Y-R,B
SG
LOCAL -20 -20 -20 -20
REMOTE HOURS
-30 -30 -30 -30
-40 -40 -40 -40 MONITOR
MONITOR
-60 -60 -60 -60 1/2 3/4 AUDIO
15 26 37 48 5/6 7/8 4 8 CH
CH- CH- CH- CH-
L
MIX
R AUDIO VIDEO
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
PHONES NEXT
PREV PLAY STOP
TOP F REV F FWD END
Turn the jog dial or shuttle dial.
Turning the jog dial clockwise increments the item
number, and turning it counterclockwise decrements the
item number. The item number changes at a rate depending
on the jog dial rotation rate.
When you turn the shuttle dial, the item number changes at
a rate depending on the shuttle dial position.
To change the currently displayed sub-item
Hold down the STOP button, and turn the jog dial or
shuttle dial.
The sub-item number changes at a rate depending on the
jog dial rotation rate or on the shuttle dial position.
Sub-item number (flashing while changing)
To skip from one item group to the next
Hold down the VAR button, and turn the jog dial or shuttle
dial.
Changing a menu item setting value
To change the setting value of the currently displayed
menu item, proceed as follows.
EJECT
REMOTE [9P iLINK] KEY INH
ALARM
VIUB COUNTER VITC REC INH
MINUTES SECONDS FRAMES
625 IMX[50 40 30]
18 24 BIT 525 DVCAM
COUNTER SYS MENU SHIFT
SELECT HOLD MENU
SUB THUMB
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MENU MARK MARK1
REC
IN OUT
MARK2
Shuttle dial
Jog dial
SG DATA SG DATA SG DATA SG DATA REMOTE [9P iLINK]
ACCESS EDIT
ANA SDI ANA SDI ANA SDI ANA SDI INPUT
AE8/EBU AE8/EBU AE8/EBU AE8/EBU VITC VIUB COUNTER
i.LINK
dB OVER dB OVER dB OVER dB OVER
0 0 0 0 SDI
CMPST
NETWORK -12 -12 -12 -12 Y-R,B
LOCAL -20 -20 -20 -20 SG
REMOTE
-30 -30 -30 -30 HOURS MINUTES
MONITOR
-40 -40 -40 -40
MONITOR 1/2 3/4 AUDIO 625
-60 -60 -60 -60
CH- 15 CH- 26 CH- 37 CH- 48 5/6 7/8 4 8 CH 18 24 BIT 525
L
MIX
AUDIO VIDEO COUNTER
R
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL SELECT
SUB
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE CLIP
REC
PRESET
PB
CLIP
MENU
PHONES
PREV PLAY NEXT STOP REC
F REV F FWD
TOP END
1
Hold down the SHUTTLE button, and turn the jog dial
or shuttle dial.
The setting value changes at a rate depending on the
jog dial rotation rate or on the shuttle dial position.
Setting value (flashing while changing)
2
When the desired setting value is displayed, press the
SET button.
This saves the new setting value, and the menu display
disappears from the time data display.
To abandon making a change
Press the MENU button before pressing the SET
button.
The menu display disappears from the time data
display without the new setting value being saved.
Resetting the menu settings to their
factory default values
To reset the current active menu settings to their factory
default values, proceed as follows.
EJECT
KEY INH ALARM
VITC REC INH
1
SECONDS FRAMES
IMX[50 40 30]
DVCAM
SYS MENU SHIFT
HOLD MENU
THUMB
NAIL SET RESET
ESSENCE S.SEL
MARK MARK1
IN OUT
MARK2
2
8-2 Basic Setup Menu
95