Sony PDW-1500 Operation Manual page 45
Professional disc recorder
Hide thumbs
Also See for PDW-1500:
- Operation manual (154 pages) ,
- Brochure (28 pages) ,
- Brochure & specs (18 pages)
Table of Contents
Advertisement
In this case, the setting of extended menu item 628 “DF
MODE” is ignored. New time code is recorded in the drop-
frame mode of the last recorded time code on the disc.
To record with the internal time code
generator synchronized to external time
code
You can record with the internal time code generator
synchronized to time code input from an external device.
Use this method to synchronize the time code generators of
a number of recorders, or to carry out recording
maintaining the synchronization between the source video
and time code.
In this case, the settings of extended menu items 627
“RUN MODE” and 628 “DF MODE” are ignored.
You can synchronize the internal time code generator to
one of the following external time codes.
• TC input to this unit’s TIME CODE IN connector
• VITC in a video signal input to this unit
• SMPTE RP188 LTC in an SDI signal input to this unit
• i.LINK TC input to this unit’s S400 (i.LINK)
connector
• i.LINK VITC input to this unit’s S400 (i.LINK)
connector
Use the following procedure to synchronize the internal
time code generator according to the type of external time
code.
EJECT
SG DATA
SG DATA
SG DATA
SG DATA
REMOTE [ 9P iLINK ]
EDIT
KEY INH
ACCESS
ALARM
ANA SDI
ANA SDI
ANA SDI
ANA SDI
INPUT
AE8/EBU
AE8/EBU
AE8/EBU
AE8/EBU
VITC
VIUB
COUNTER
VITC
REC INH
i.LINK
dB
dB
dB
dB
OVER
OVER
OVER
OVER
0
0
0
0
SDI
CMPST
NETWORK
-12
-12
-12
-12
Y-R,B
SG
LOCAL
-20
-20
-20
-20
REMOTE
HOURS
MINUTES
SECONDS
FRAMES
-30
-30
-30
-30
-40
-40
-40
-40
MONITOR
MONITOR
IMX [ 50 40 30 ]
1/2
3/4
AUDIO
625
-60
-60
-60
-60
15
26
37
48
CH-
CH-
CH-
CH-
5/6
7/8
4 8 CH
18 24 BIT
525
DVCAM
L
MIX
AUDIO
VIDEO
COUNTER
SYS MENU
SHIFT
R
MONITOR SEL METER SEL
INPUT CH
INPUT SEL
INPUT SEL
SELECT
HOLD
MENU
SUB
THUMB
ALL/CH-1
CH-2
CH-3
CH-4
CLIP
NAIL
SET RESET
VARIABLE
REC
PRESET
PB
CLIP
ESSENCE
S.SEL
MARK1
MENU
MARK
PHONES
PLAY
NEXT
PREV
STOP
REC
IN
OUT
F REV
F FWD
TOP
END
MARK2
1
2
1
Make either of the following connections and settings.
To synchronize to time code input to the TIME
CODE IN connector
Connect the time code output from the external device
to the TIME CODE IN connector. Press the VIDEO
INPUT SEL button and, while viewing the INPUT
display, select one of SDI, CMPST, or SG.
To synchronize to VITC in an input video signal
Connect a video signal containing VITC to the VIDEO
IN connector or the SDI IN connector. Press the
VIDEO INPUT SEL button and, while viewing the
INPUT display, select CMPST or SDI.
To synchronize to SMPTE RP188 LTC in an SDI
signal
Connect an SDI signal containing SMPTE RP188
LTC to the SDI IN connector.
To synchronize to i.LINK TC
Connect an i.LINK signal to the S400 (i.LINK)
connector. Press the VIDEO INPUT SEL button and,
while viewing the INPUT display, select i.LINK.
To synchronize to i.LINK VITC
Connect an i.LINK signal to the S400 (i.LINK)
connector. Press the VIDEO INPUT SEL button and,
while viewing the INPUT display, select i.LINK.
2
Make the following settings.
To synchronize to time code input to the TIME
CODE IN connector
• Set extended menu item 626 “TC MODE” to “ext
regen.”
• Set extended menu item 629 “TC SELECT” to “tc.”
To synchronize to VITC in an input video signal
• Set extended menu item 626 “TC MODE” to “ext
regen.”
• Set extended menu item 629 “TC SELECT” to
“vitc.”
To synchronize to SMPTE RP188 LTC in an SDI
signal
Set extended menu item 626 “TC MODE” to “rp188
regen.”
To synchronize to i.LINK TC
• Set extended menu item 626 “TC MODE” to “ext
regen.”
• Set extended menu item 629 “TC SELECT” to “tc.”
To synchronize to i.LINK VITC
• Set extended menu item 626 “TC MODE” to “ext
regen.”
• Set extended menu item 629 “TC SELECT” to
“vitc.”
For details of menu setting operations, see Chapter 8
“Menus” on page 90.
This starts the internal time code generator running in
synchronization with the external time code generator.
Once the internal time code generator is synchronized
with the external time code generator, even if the
external time code generator connection is removed,
the internal time code generator continues to run.
Notes
• When the input video signal selected is i.LINK or SDI,
(the INPUT display shows i.LINK or SDI), setting
Page 45
- Quick Links:
- Error Messages
Hide quick links:
Advertisement
Table of Contents
