Download Print this page
Shure WL183 User Manual
Shure WL183 User Manual

Shure WL183 User Manual

Wireless lavalier microphones
Hide thumbs Also See for WL183:

Advertisement

Quick Links

WL183, WL184, AND WL185 LAVALIER MICROPHONES
GENERAL
Models WL183, WL184 and WL185 are lavalier electret condenser
microphones designed for use with a wireless bodypack transmitter. Each
microphone has a 1.2 meter (4 ft.) cable terminated with a miniature
Switchcraft TA4F connector. The furnished tie clip can be rotated in 90
intervals for placement flexibility.
APPLICATIONS
WL183 (Omnidirectional): Recommended for general purpose
sound reinforcement, recording, or remote monitoring applications.
Low handling noise. Pickup angle is 360 .
WL184 (Supercardioid): Recommended for sound reinforcement ap-
plications requiring high rejection of ambient noise and narrow pickup
angle. Use of windscreen highly recommended. Pickup angle is 115 .
WL185 (Cardioid): Recommended for general purpose sound rein-
forcement applications requiring good rejection of ambient noise. Use
of windscreen highly recommended. Pickup angle is 130 .
INSTALLATION
1. Insert the top of the microphone through tie clip loop from below until
tie clip loop snaps into place over the lower groove on the micro-
phone. Refer to the following illustration.
2. To install the snap–fit windscreen, press it down on the microphone
until it clicks into place inside the upper groove on the microphone.
The snap–fit windscreen provides 30 dB of pop protection.
NOTE: The snap–fit windscreen can be removed by spreading the
slot in the plastic snap–fit ring.
To install the smaller foam windscreen, slip the windscreen over the
top of the microphone so that it covers the side slots.The foam wind-
screen provides 5 to 10 dB of pop protection.
TIE CLIP
3. Attach the microphone approximately 76 mm to 152 mm (3 to 6 in.)
below the neckline.
NOTE: Do not cover the microphone with your hand or clothing.
CHANGING CARTRIDGES
The WL183, WL184, and WL185 microphones use interchangeable
cartridges. To remove the cartridge, unscrew the tip of the microphone
and remove it. Install the replacement cartridge by screwing it onto the
microphone base.
REPLACEMENT PARTS AND ACCESSORIES
Omnidirectional Cartridge
. . . . . . . . . . . . . . . . . . . . . . . . . .
Supercardioid Cartridge
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Cardioid Cartridge
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Snap–fit Windscreens (4)
. . . . . . . . . . . . . . . . . . . . .
Foam Windscreen (4)
. . . . . . . . . . . . . . . . . . . . . . . . . .
Tie clips (2)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Miniature 4-pin connector
. . . . . . . . . . . . . . . . . . . . . . . . .
27B2833 (AA)
2001, Shure Incorporated
OR
WINDSCREEN
Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ Ñ
R183B
R184B
R185B
RK183BWS
RK261WS
RK183T1
WA330
Wireless Lavalier Microphone User Guide
SPECIFICATIONS
Type: Condenser (electret bias)
Frequency Response: 50 to 17,000 Hz
WL183 FREQUENCY RESPONSE
+10
0
–10
20
50
100
200
WL184 FREQUENCY RESPONSE
+10
0
–10
20
50
100
200
WL185 FREQUENCY RESPONSE
+10
0
–10
20
50
100
200
Polar Patterns (at 1 kHz):
o
180
o
o
150
150
150
o
o
120
120
o
120
o
o
90
90
o
90
–20 dB
–15 dB
o
o
60
60
o
60
–10 dB
–5 dB
o
30
o
30
30
0
OMNIDIRECTIONAL
(WL183)
Output Impedance : 1800 Ω
Sensitivity (1 Pa = 94 dB SPL):
Maximum Sound Pressure Level: WL183: 125.0 dB SPL
Output Noise (A–weighted):
Dynamic Range: 102.5 dB
Polarity: Positive pressure on diaphragm produces positive voltage on
pins 3 and 4 relative to pin 1.
Power Requirements: Regulated nominal +5 Vdc (1.5 Vdc to 10 Vdc)
provided at microphone connector pin 2 relative to pin 1 of a Shure
wireless microphone transmitter.
NOTE: For additional technical assistance, phone Shure at (847)
866-2200. In Europe, phone 49-7131-72140.
IMPEDANCE CONVERTER
CONDENSER
CARTRIDGE
MICROPHONE WIRING DIAGRAM
500
1,000
2,000
5,000 10,000
500
1,000
2,000
5,000 10,000 20,000
500
1,000
2,000
5,000 10,000
o
180
180
o
o
o
150
150
o
o
120
120
o
o
90
90
–20 dB
–20 dB
–15 dB
–15 dB
o
o
60
60
–10 dB
–10 dB
–5 dB
–5 dB
o
o
o
30
30
0
SUPERCARDIOID
CARDIOID
(WL184)
(WL185)
WL183: –40.0 dBV/Pa
WL184: –44.5 dBV/Pa
WL185: –45.5 dBV/Pa
WL184: 129.5 dB SPL
WL185: 130.5 dB SPL
WL183: 22.5 dB SPL
WL184: 27.0 dB SPL
WL185: 28.0 dB SPL
2
1
D+
RED
4
G
3
BLK
S
SHIELD
Printed in U.S.A
20,000
20,000
o
o
150
o
120
o
90
o
60
o
30
0
1 GROUND
2 BIAS
3,4 AUDIO

Advertisement

loading

Summary of Contents for Shure WL183

  • Page 1 Power Requirements: Regulated nominal +5 Vdc (1.5 Vdc to 10 Vdc) cartridges. To remove the cartridge, unscrew the tip of the microphone provided at microphone connector pin 2 relative to pin 1 of a Shure and remove it. Install the replacement cartridge by screwing it onto the wireless microphone transmitter.
  • Page 2 All WL93 models include a 1.2 m (4 ft.) cable terminated with a miniature 4-pin connector (Switchcraft 1,000 2,000 5,000 10,000 20,000 TA4F type) which connects directly to a Shure wireless body-pack FREQUENCY IN Hz transmitter. Polar Pattern: Omnidirectional, uniform with frequency VARIATIONS Output Impedance: 3000 Ω...

This manual is also suitable for:

Wl184Wl185Wl93Wl93tWl93–6tWl93–6