Download  Print this page

Troubleshooting; One-Year Limited Warranty; Care And Maintenance - Black & Decker LEDLIB Instruction Manual

Lithium-ion led spotlight
Hide thumbs

Advertisement

locking the spotlight
To lock the spotlight in the on position, depress the On/Off Trigger, then press the trigger lock bar. The spotlight
will stay on until the trigger unlock bar is pressed and the On/Off Trigger is released.
If the On/Off Trigger is released when the trigger lock bar is pressed, the spotlight will be locked in the off
position. To turn the spotlight on again, press the trigger unlock bar before pressing the On/Off Trigger.
Using the light mode select button
The spotlight offers two brightness modes.
When the spotlight is first turned on, the light is operating at maximum brightness. To operate the spotlight at
medium brightness, press the Light Mode Select Button on the back of unit once. Press it again to switch back
to maximum brightness.
operating the unit corded
Plug the barrel tip of the supplied 12 volt DC adapter into the 12 volt DC power and charging port at the back of
the unit.
Insert the plug end into the accessory outlet of your vehicle or other 12 volt DC power source. Operate the unit
as outlined in the previous section.
IMPORTANT: The spotlight will operate while the 120 Volt AC Adapter is attached, but will continue to draw
power from the unit's Lithium-Ion battery while the spotlight operates. This may cause the low voltage
protection to activate and shut the spotlight down. Manufacturer recommends only operating the unit in corded
mode using the 12 Volt DC Adapter.
Using the locking Adjustable stand
Snap the Locking Adjustable Stand up, invert the unit and set it upon a flat, stable surface for hands-free
operation.
Using the carry lanyard (optional accessory)
The carry lanyard may be used to carry the unit or to hang it for storage. Always adjust the slide on the cords to
keep the lanyard secure around any supporting object.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When light is hung by the carry lanyard, do not shake the spotlight or object that it is hanging from. Do not
hang the spotlight from any electrical wires or anything that it is not secure.
• Only use the carry lanyard for hanging this spotlight. The carry lanyard is not intended to support additional
weight. Do not attach or hang anything additional to the spotlight or risk of breakage may occur.

cAre AND MAiNteNANce

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit
is not in use, we recommend that the battery is charged at least every 3 to 6 months.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with
a soft cloth moistened with a mild solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires.
Contact manufacturer to replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Contact manufacturer for any information you may need.
SAFE BATTERY DISPOSAL
Contains a lithium-ion battery, which must be disposed of properly. Recycling is required, contact your local
authority for information. Failure to comply with local, state and federal regulations can result in fines,
or imprisonment.
Contact your local waste management authority to dispose of this product.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting
(shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
12 volt Dc Adapter plug fuse replacement
The fuse in the plug end of the 12 Volt DC Adapter protects the adapter's charging circuit. If the 120 Volt AC
Adapter operates, but the DC charging adapter does not, then this fuse may be opened (blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 5 amp fuse.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 volt DC adapter.

troUBleshootiNg

Problem
The battery/charge status LED
indicator does not light when
charging
Unit will not operate

oNe-yeAr liMiteD wArrANty

The manufacturer warrants this product against defects in materials and workmanship for a period of ONE (1)
YEAR from the date of retail purchase by the original end-user purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the defective product can be
replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or replacement
at manufacturer's option. Proof of purchase may be required by manufacturer. (2) Return the product to the
retailer where product was purchased for an exchange (provided that the store is a participating retailer).
Returns to retailer should be made within the time period of the retailer's return policy for exchanges only
(usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and
tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse,
abuse; and failure to follow instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which
vary from state to state or province to province. This product is not intended for commercial use.
PLEASE
RECYCLE
Solution
1. Check connection to the 12 Volt DC Charging Port.
2. Check connection to AC or DC power source.
3. Confirm there is a functioning AC or DC current.
4. Check that the fuse in the 12 Volt DC Adapter is not blown.
1. The unit may have shut down to protect the battery from
overheating after long term operation or charging/recharging.
Allow the spotlight to cool down for several minutes before
resuming operation.
2. The battery may be completely discharged. Charge the unit
following the directions.

Hide quick links:

Advertisement

loading

  Related Manuals for Black & Decker LEDLIB