Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Platinum Manuals
  4. Car Alarm
  5. APS-997C
  6. Installation manual

Platinum APS-997C Installation Manual

2 way lcd vehicle security and remote start system
Hide thumbs Also See for APS-997C:

Advertisement

Quick Links

Download this manual See also: Owner's Manual
Table Of Contents:
Before You Begin
Wire Harnesses Quick View
Installation Of The Major Components
Wiring The 6 Pin Main Power Harness
Wiring The 4 Pin Alternate Ignition Harness
24 Pin Accessory Input/Output Harness
3 Pin Door Lock Harness Wiring
Auxiliary Output Harness Wiring
2 Pin Transponder Control Output
Upgrade Telematic Module
6 Pin Antenna Harness And Program Push Button Switch
4 Pin Shock Sensor
DBI Port Information
Timed Start Program And Information
Temperature Start Programming And Information
Diesel Engine Settings Information
Diagnostics Access
Engine Monitoring Selections, (Voltage Tach, DBI, Hybrid,)
Tach Programming
Multi Coil Adaptor (Optional) Information
Testing Your Installation Hood Pin Safety
Manual Override Safety Testing and Operation
Neutral Start Switch Safety Test
Completing Your Installation
Dome Delay Learn Circuit
Shock Sensor Adjusting
Programming Transmitters Bank 1
Programming Alarm Feature Bank 2
Programming Remote Start Feature Bank 3
Circuit Wiring Layout
Notes
Rev B: New Format Add Timing PASD & Light Blue + DBI Lock, Lock, Lock 5/2013
If booklet format, pages 26-30, Programming & Wiring Diagram shall be foldout or seperate 5 sheets
front & back.
PATENTED: www.voxxintl.com/company/patents
Model APS-997C
Installation Manual
2 Way LCD Vehicle Security and
Remote Start System
Page 2
Page 3 and 4
Page 5
Page 6
Page 7
Page 8
Page 14
Page 16
Page 17
Page 17
Page 17
Page 17
Page 18
Page 18
Page 18
Page 18
Page 19
Page 19
Page 19 and 28
Page 20
Page 20
Page 21
Page 21
Page 24
Page 24
Page 24
Page 26
Page 26 and 27
Page 28 and 29
Page 30
Page 31-32
1
128-8775b
1 of 32

Advertisement

loading

Related Manuals for Platinum APS-997C

Summary of Contents for Platinum APS-997C

  • Page 1 Model APS-997C Installation Manual 2 Way LCD Vehicle Security and Remote Start System Table Of Contents: Before You Begin Page 2 Wire Harnesses Quick View Page 3 and 4 Installation Of The Major Components Page 5 Wiring The 6 Pin Main Power Harness...

  • Page 2: Before You Begin

    Before You Begin PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED Roll down window to avoid locking the keys in the vehicle during installation. Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle.
  • Page 3 24 Pin Main Wiring Harness #1123193 Dark Blue/Black External Remote Start Trigger Input Brown/Black Brake Shutdown Input (+) Dark Green Instant Trigger Input Hood & Trunk Green/Orange Tachometer Input Black Chassis Ground Green/Yellow Diesel Wait To Start Input Light Blue/Green Channel 5 Output (-) 300mA Blue/Red Channel 7 Output (-) 300mA...
  • Page 4 6 Pin Power / Start Harness #1123742 Purple Accessory (+) Blue Ignition 1 (+) Battery 2 - 12V (+) Red/White Battery 1 - 12V (+) Yellow Starter Output Green Ignition 2 (+) 4 Pin 3rd Ignition / Start Harness #1123743 Orange/Black Parking Brake Input (-) Red/Black...
  • Page 5 This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel Injection Gas or Diesel Vehicles Only! INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: PART # 1365026 Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24"...
  • Page 6 IMPORTANT! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS.
  • Page 7 ( when used ) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.
  • Page 8 WIRING CONNECTIONS: 24 Pin Accessory Input/Output Harness PART # 1123193 1 Dark Blue/Black Trace Wire: External Trigger Input The Dark Blue/Black trace wire allows the remote start unit to be activated from an external source. The intent of this wire is to allow the unit to be controlled from a "POSSE/CAR-LINK" paging system or similar device.
  • Page 9 activates. The remote start sees the green/yellow with positive voltage and waits for this to go inactive( drop the 12 volts) before activating the starter motor. If this wire is not used or you have difficulty accessing the glow plug preheat circuit, you may elect to utilize the Diesel timed output as specified in Remote Start feature selection #9.
  • Page 10 12 White Wire: Parking Light Flasher Output This wire is the normally open contact of the on board parking light flash relay. Connect this wire to the vehicle's parking light feed wire. This is the wire that gets switched on, either (+) or (-), when the vehicle's parking light switch is activated.
  • Page 11 ground trigger output wire of motion detectors, microwave detectors, or glass break detectors, can be connected to this Light Green trigger input wire. 17 White w/ Black Trace Wire: (+) Siren Output This is the positive siren feed wire. Route this wire through a grommet in the firewall to the siren location. Connect the White w/ Black Trace wire to the Red wire of the Siren.
  • Page 12 21 Light Blue Wire: Ground Output While Running (-) 300mA This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off.
  • Page 13 NOTE: This is a normally opened starter cut arrangement, when power is removed from the secu- rity system, the starter disable feature will remain operational, and the vehicle will not start. Audiovox does not recommend using the Orange w/ White trace wire to interrupt anything but the starting circuit of the vehicle.
  • Page 14 24 White w/ Red Trace Wire: Parking Light Flasher Input This wire is the common contact of the on board parking light flasher relay. If the vehicle you are working on has +12 volt switched parking lights, connect this wire to a fused + 12 volt source. (Max. 15 Amps) NOTE: If the vehicle's parking lights are ground switched, connect this wire to chassis ground.
  • Page 15 3 WireGround Switched Door Lock/Unlock Wiring Detail 3 Wire Positive Switched Door Locks: In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay.
  • Page 16 These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits.
  • Page 17 4 Black w/ Yellow Trace Wire: Ground Output During Start (Crank) The Black w/ Yellow Trace wire will provide a 300 mA ground output while the starter output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GM vehicles.
  • Page 18 (Connector Port) The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder interfaces for remote starting.
  • Page 19 Monitoring The Vehicle's Engine: (Program Feature #5 Bank 3) There are 4 ways that the remote start monitors the engine running, one or the other must be selected for your application for the remote start to operate correctly. 1) VOLTAGE SENSE SETTING: The unit will monitor the voltage level of the battery during remote start, wait for the voltage to drop while cranking, then look for the voltage level to go above the level it was before the vehicle began to crank which indicates the vehicle is running.
  • Page 20 3. Connect the Yellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the on and start position and have 0 volts with the ignition in the off position. 4. Connect the Green wire to the (Green) or (Orange/Green) tach input of the Audiovox remote start unit. TESTING YOUR INSTALLATION: WARNING!! The following procedure must be performed after the installation of any Remote Start Device.
  • Page 21 REMOTE START OVERRIDE MODE / MANUAL SHUT DOWN: The intent of the remote start override / manual shut down circuit is to allow the vehicle operator to prevent operation of the Remote Start Unit regardless of the RF transmitter operation. To Enter The Remote Start Override Mode: 1) With the system disarmed/unlocked, and the ignition switch off Press and Hold the pushbutton switch located on the receiver unit on.
  • Page 22 Mechanical Neutral Start Switch from starting in gear. AUDIOVOX ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available.
  • Page 23 5) Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non striped) side to the negative shut down safety wire (Gray / Black) of the Audiovox Remote Start Unit. 6) Connect terminal 86 of the relay to a fused +12 volt constant battery source.
  • Page 24 To connect to the key in sensor circuit as shown for method 2: 1) Locate the control wire that connects the drivers door pin switch to the key in sensor switch. 2) Cut this wire and connect the ignition cylinder side to chassis ground. 3) Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .
  • Page 25 To decrease sensitivity, turn the adjustment screw counter clockwise. COMPLETING THE INSTALLATION: After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: 1) Mount the control module up and behind the dash securing it in place with cable ties or screws. Be certain that the chosen mounting location will not inhibit any of the controls of the vehicle.
  • Page 26 The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. PROGRAMMING BANK 1 (TRANSMITTERS): 1) Turn the ignition key to the on position. 2) Press and release the valet/programming switch 3 times (Siren Chirps). 3 Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren.
  • Page 27 128-8775b 27 of 32...
  • Page 28 PROGRAMMING BANK 3 (REMOTE START ): You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you've made the changes you wanted in Bank 2, (Siren two Long Chirp), You can also go right to bank 3 by: 1) Turn the ignition key to the on position.
  • Page 29 128-8775b 29 of 32...
  • Page 30 For technical support go to www.prestigecarsecurity.com or call 1 800 225 6074 © 2013 Audiovox Electronics Corp., Hauppauge, NY 11788 128-8775b 128-8775b 30 of 32...
  • Page 31 NOTES NOTES 128-8775b 31 of 32...
  • Page 32 NOTES 128-8775b 32 of 32...