Warranty; Troubleshooting - Black & Decker BDPS200 Instruction Manual

Power paint sprayer
Hide thumbs Also See for BDPS200:
Table of Contents

Advertisement

Available languages

Available languages

Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The
defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased
(provided that the store is a participating retailer). Returns should be made within the time period of the retailerʼs policy
for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer
for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for
repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service
Centers are listed under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other
rights which vary from state to state or province to province. Should you have any questions, contact the manager of
your nearest Black & Decker Service Center. This product is not intended for commercial use.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,
check country specific warranty information contained in the packaging, call the local company or see the website for
warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call
1-800-544-6986 for a free replacement.
Problem
• Material runs or drips
• Too much over spray.
• Little or no material being released.
• Material being sprayed is splattering.
• Sprayer pulsates.
• Liquid comes out side of canister.
• Motor operates properly but does
not spray.
• Cannot reassemble unit.
For assistance with your product, visit our website www.blackanddecker.com for the location of the
service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986.
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.

TROUBLESHOOTING

Possible Cause
• Spraying too much material.
• Spraying too slowly.
• Spraying too close.
• Viscosity too thin.
• Sprayer too far from surface.
• Too much material being sprayed.
• Spray nozzle/tip clogged.
• Pickup tube loose or clogged.
• Flow control knob setting too low.
• Material too thick.
• Viscosity of material is too low.
recommendation.
• Material in canister almost empty.
• Lid not on square or tight enough.
• Paint on threads of canister and lid. • Clean threads on top and sides of
• Plugged or worn atomizer valve.
• Atomizer valve missing.
• Material too thick.
• Plugged spray tip.
• Intake filter plugged.
• Control knob needs adjusting.
• Worn piston.
• Skipped an assembly step.
Imported by

WARRANTY

14
Possible Solution
• Reduce air flow by turning flow control
knob.
• Increase speed of application.
• Increase distance from surface.
• Check dilution recommendation.
• Reduce distance to surface.
• Reduce flow by turning flow control
knob clockwise.
• Clean nozzles.
• Check tube.
• Increase flow control setting.
• Check viscosity recommendation.
• Thin material per manufacturer
• Refill canister.
• Remove lid and reattach squarely and
evenly, then tighten cap securely.
canister and lid.
• Clean or replace as needed.
• Put in atomizer valve.
• Thin material.
• Clean tip.
• Clean intake filter.
• Adjust knob.
• Clean and oil or replace
• Insert spring and piston into the housing
prior to reassembling.
• Press and hold the release button
while reassembling.
See 'Tools-Elec-
tric'
– Yellow Pages –
for Service &
Sales

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents