Clean Channel - B-52 LS-100 Instruction And User's Manual

B-52 LS-100: 100-WATT TRI-CHANNEL GUITAR AMPLIFIER
LS-100 FRONT PANEL CONTROLS
POWER
LS 0 0
ON
1
1. POWER ON/OFF SWITCH: Turns the LS-100
on and off.
2. MASTER VOLUME: Controls the overall loudness of
the LS-100. To increase the overall volume, rotate the
control clockwise. The Master volume control allows
you to control the volume of both the Clean and
Overdrive Channels simultaneously.
3. MASTER REVERB CONTROL: Adjusts the amount
of reverb produced by the amplifier. To increase the
amount of reverb, turn clockwise.
4. CLEAN CHANNEL – VOLUME: Controls the overall
LS-100 REAR PANEL CONTROLS
EFFECTS LOOP
RETURN
0 10
LEvEL
23
22
22. EFFECTS – RETURN LEVEL: Controls the level of
the returning signal from an effects unit.
23. EFFECTS – RETURN JACK: Connects the LS-100 to
the output of an effects unit.
24. EFFECTS - SEND JACK: Connects the LS-100 to
the input of an effects unit.
4
vOLUME
- 1
0
vOLUME
2
signal level of the clean channel.
5. CLEAN CHANNEL - MID CUT: Pushed in, this
feature sets the perfect amount of midrange for a
truly pristine, almost acoustic-like sound.
6. CLEAN CHANNEL - TREBLE: Adjusts the amount of
high frequency boost or cut as desired in the clean
channel. Treble adds brightness to your tone. Turning
this control clockwise will add clarity to your sound.
Turning the control counter-clockwise softens the tone.
7. CLEAN CHANNEL - MIDDLE: Adjusts the amount
of mid-range frequencies as desired in the clean
SENd
0 10
LEvEL
24
25
25. EFFECTS – SEND LEVEL: Controls the signal level
being sent to an effects unit.
26. FOOTSWITCH –REVERB: Connects footswitch to
turn the reverb on/off
27. FOOTSWITCH – GAIN AND CHANNEL
SWITCH: Switch between Gain 1 and Gain 2 in
MASTER
REvERB
0 10
10
REvERB
3
CAUTION
RISK OF ELE CTRIC SHOCK
DO NOT OPEN
FOOTSWITCH
CHANNEL
REvERB
GAIN
27
26

CLEAN CHANNEL

vOLUME TREBLE
MID
CUT
0 10
0 10
vOLUME TREBLE
6
4 5
channel. Turning the middle control clockwise will
increase the amount of warmth. Counterclockwise
settings create a more hollow, mid-scooped tone.
8. CLEAN CHANNEL - BASS: Adjusts the amount of
low frequency boost or cut as desired. Adding bass will
increase the depth and fullness of your sound.
9. CHANNEL SELECT: Push switch selects between the
clean and overdrive channels. Activated LED lights
indicate which channel is in use.
10. OVERDRIVE – VOLUME 2: Controls the overall
volume of the high gain overdrive channel.
WARNING: To reduce the risk of electrical shock, do not expose this
equipment to rain or moisture. There are no user serviceable parts inside.
Refer all servicing to authorized personnel.
CAUTION: To reduce the risk of fire replace only with the same type of fuse.
RECORd OUT
0 10
SPEAkER
SIMULATEd
LEvEL
29
28
the Overdrive channel. Also switches between clean
and overdrive channel.
28. RECORD OUT – LEVEL: Controls the signal level
being sent to the PA or recording console.
29. RECORD OUT – SPEAKER SIMULATED: This
output signal is pre-equalized to simulate the sound
C
MIddLE BASS
0 10 0 10
MIddLE BASS
7
8