Selecting And Playing A Program Or Combination; Selecting A Program; Using Controllers To Modify The Sound - Korg TRITON Quick Start Manual

Selecting and playing a program or combination

5
1
REALTIME CONTROLS
VOLUME
LPF CUTOFF RESONANCE/HPF
ASSIGNABLE 1 ASSIGNABLE 2
INPUT TRIM ULTRA BOOST
5
2

Selecting a program

1 Press the [PROG] key (it will light).
You're in Program mode. Make sure that the Pro-
gram P0: Play page is displayed.
In this page you can select and play programs.
If this page is not displayed, press the [EXIT] key and
then the Perf. Edit tab.
2 Make sure that "Program Select" is highlighted in
the display.
If not, press "Program Select" in the display to high-
light it.
3 Select a program, and play it.
Use the [ ][ ] keys to select a program.
You can also select a program by turning the
[VALUE] dial.
Press one of the [BANK] keys to select programs
from other banks (A–E, G–N).
You can also select a program by using numeric keys
[0]–[9] and the [ENTER] key, but here we will
explain how to select programs by category, such as
"keyboard" or "pad."
In the LCD, press the Category popup button.
A menu will appear. Press one of the tabs displayed
at the left and right sides ("00 Keyboard"–"15
Drums"), select one of the programs that appear in
the menu in the center of the screen, and play it. You
can use the scroll bar to see other programs of the
same category. When you find a program you like,
press the OK button to close the dialog box.
4
5 9
3 1
ON/OFF
COMBI
A
EG-INTENSITY EG-RELEASE
B
SEQ
ASSIGNABLE 3 ASSIGNABLE 4
VALVE FORCE
TUBE GAIN OUTPUT LEVEL
S.PLAY
MEDIA
Tab
Scroll bar
Press the scroll
bar to view other
programs of the
same category.
1 3
1 1
PROG VALUE
SAMPLING
GLOBAL
COMPARE
Perf. Edit
Tab

Using controllers to modify the sound

4 While playing the keyboard, you can use the joy-
stick, ribbon controller, and [SW1]/[SW2] keys to
modify the sound.
The result will be different for each program; try
each controller to hear what it does for the program
you've selected.
SW 1
Pitch down, etc.
5 Using the REALTIME CONTROLS [1]–[4]
Use the [REALTIME CONTROLS] key to select
either A, B, or VALVE FORCE as the set of parame-
ters that will be controlled by these four knobs. Turn
knobs [1]–[4] to modify the sound accordingly.
When "A" is selected, the four knobs will control
low-pass cutoff frequency, resonance (or the high-
pass filter cutoff frequency), filter EG depth, and the
release time of the filter and amp EGs.
When "B" is selected, the four knobs will control
various parameters depending on the program, such
as volume, portamento time, pan, pitch LFO, or
master effect send levels.
When " VALVE FORCE " is selected, the four knobs
will control the input level to Valve Force, ultra
boost, tube gain, and the output level from Valve
Force. If you want to use Valve Force, press the
[ON/OFF] key to make it light.
Depending on the sound you are using, you may hear
noise if you turn the Valve Force knobs or edit Valve
Force parameters while sound is being produced.
2 1 3
Category popup button
2 4
Program Select
(Category/Program Select)
SW 2
Switch the octave, turn portamento
on/off, the Lock function, etc.
Vary the vibrato depth or the speed of the
rotary speaker, etc.
Pitch up, etc.
Wah, effect depth, etc.
Pitch, volume, filter
depth, etc.