GE Monogram ZV950 Installation Instructions Manual
36" stainless steel vent hood
Hide thumbs
Also See for Monogram ZV950:
- Use and care manual (14 pages) ,
- Installation instructions manual (12 pages) ,
- Owner's manual (12 pages)
Related Manuals for GE Monogram ZV950
Summary of Contents for GE Monogram ZV950
- Page 1 Installation Instructions If you have questions, call 800.GE.CARES or visit our website at: www.monogram.com ZV950 36" Stainless Steel Vent Hood...
-
Page 2: Safety Information
Safety Information WARNING: BEFORE YOU BEGIN TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, Read these instructions completely and carefully. OBSERVE THE FOLLOWING: IMPORTANT A. Use this unit only in the manner intended by the for local inspector’s use. manufacturer. -
Page 3: Table Of Contents
Design Information CONTENTS Design Information ..............8 Product Dimensions and Clearances ........Installation Instructions Optional Accessories ........................ Installation Preparation ........... Advance Planning, ............................5 ..............Power Supply .................... 5 ............... Duct Fittings ....................6 Step 6, Connect Electrical ..............Tools and Materials Required ............7 Step 7, Install Duct Covers ............... -
Page 4: Design Information
Design Information PRODUCT DIMENSIONS AND CLEAR- OPTIONAL ACCESSORIES ANCES (cont.) ZX14SDSS, optional stainless steel duct cover is available Using Duct Cover Accessories Order the optional duct cover at the same time as the A Duct Cover Accessory may be required for your hood installation height. -
Page 5: Installation Preparation
Installation Preparation ADVANCE PLANNING Ductwork Planning mum equivalent duct length to 75 feet. opening. Order the wall or roof cap and any transition needed in advance. Wall Framing for Adequate Support permissible length for duct runs to the outdoors. must be provided. The hood must be secured to vertical air system in accordance with local building code requirements. -
Page 6: Duct Fittings
Installation Preparation Total DUCT FITTINGS Equivalent Quantity Equivalent Duct Piece Dimensions Length* Used Length This Hood Must Use 8" Round Duct. It Can Transition to 3-1/4" x 12" Duct. straight length permissible lengths for duct runs to outdoors. Note: sible equivalent lengths! Maximum duct length: 100 ft. -
Page 7: Tools And Materials Required
Installation Preparation TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED) Properly grounded branch circuit. REMOVE THE PACKAGING the top of the hood. Two are located at the bottom of the be removed. It is secured with two screws. All screw im pressions are Phillips. Top Of Hood Remove Bottom Shipping Shipping Board... -
Page 8: Check Installation Hardware
Installation Preparation DUCTWORK, WIRING LOCATIONS CHECK INSTALLATION HARDWARE FOR CEILING 6 Wall 6-1/4" VENT DUCTING Centerline To Wall Fasteners Screws 8-1/2" Dia. Hole Centerline 8" Min. Above Top Mounting Bracket Holes FOR WALL VENT DUCT • Drill 1/8" Pilot Holes For Mounting Brackets. 2 Large 5-7/8"... -
Page 9: Installation Instructions
Installation Instructions 2 INSTALL MOUNTING BRACKETS 1 INSTALL FRAMING FOR HOOD SUPPORT This vent hood must be secured to the horizontal support or wall studs. IMPORTANT: Framing must be capable of supporting 100 lbs. all mounting screw locations. 8" Min. Opening for Ductwork horizontal support. -
Page 10: Install The Hood
Installation Instructions 3 INSTALL DUCT BRACKET Pre-Tap Pre-Tap Side Side top. Screw Screw Secure the bracket to the ceiling and wall: and install wall fastener anchors. screws and/or fasteners. 4 INSTALL THE HOOD Bracket Tabs center. 3. Remove the hood from the wall. The two lower holes can be enlarged to 3/8"... -
Page 11: Connect Ductwork
Installation Instructions 5 CONNECT DUCTWORK Air Flow Duct Tape Over Seam the duct stops. and Screw Screw Duct Tape CAUTION: Over Flange Do not use sheet metal screws at Duct Stops damper operations. Seal connection with tape only. PRUDENCE du collet de la hotte. Ceci empêcherait le bon fonctionnement du registre. -
Page 12: Install Filters
Installation Instructions 8 INSTALL FILTERS wards the rear and tilt downwards. the slots. 9 FINALIZE INSTALLATION materials. Note: While performing installations described in this For Monogram local service in your area, call 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric.