Skin Detail Correction; Adjusting Color In The Specified Area; Important Notes On Operation; Characteristics Of Ccd Sensors - Sony DXC-D30WSP Service Manual

Settings for Special Cases

Skin Detail Correction

The DXC-D30/D30P provides an easy push-button
function that designates an active skin tone area.
1
ON
OFF
SET
2,3
SKIN DTL
1
Set the SKIN DTL switch to ON.
The indication "SKIN AREA: ±0" appears in the
viewfinder.
2
Press the SKIN DTL SET button.
This causes the area detect cursor to be shown in
the viewfinder (for 10 seconds).
3
Place the area detect cursor on the target, then
press the SKIN DTL SET button.
This designates the correction area, which is
indicated by a zebra pattern, and the indication
"SKIN AREA: ±0" appears again. If the area
detect cursor disappears before designating the
area, press the SKIN DTL SET button again to
display the cursor. (Return to step 2.)
4
Press the UP/ON or DOWN/OFF button to change
the SKIN AREA value (–99 to +99)so that the
zebra pattern may be displayed in the target area.
Use basic menu page 3 to set the correction level
(see page 52).
You can also change color in the designated area
(see the following section).
84
Chapter 5 Adjustments and Settings
Adjusting Color in the Specified
Area
You can adjust the specified color using setup files.
Perform the same procedure with the skin detail
correction to designate the target area .
1
Turn the POWER switch on with holding down the
UP/ON button.
2
Perform steps 1 and 2 in "Changing File Settings"
(page 64) and display advanced menu page 11 in
the most suitable file for shooting.
P A G E 1 1 ( N E X T m$ P R E V m4)
F I L E A D J 2
F I L E :
S A T : 3 3
H U E : 2 2
mS K I N S A T : 1 2
S K I N H U E : 1 5
E X I T M E N U ( Y E S m4)
3
Perform the procedure for the skin detail correction
to designate the area to which you apply color
adjustment.
While this procedure is being performed, the menu
is not displayed.
4
When advanced menu page 11 appears, change the
value of the SKIN SAT or SKIN HUE to adjust
color in the area designated in step 3.
Note
Set the SKIN DTL to 1.0 in basic menu page 3 if the
skin detail correction is unnecessary.

Important Notes on Operation

Fitting the zoom lens
It is important to fit the lens correctly, as otherwise
damage may result. Be sure to refer to the section
"Fitting the Lens" (See page 26).
Do not cover the unit while operating
Putting a cloth, for example, over the unit can cause
excessive internal heat build-up.
Operation and storage
Avoid storing or operating the unit in the following
conditions.
• In excessive heat or cold (operating temperature
range: –10 °C to +45 °C (14 °F to 113 °F))
Remember that in summer in warm climates the
temperature inside a car with the windows closed can
easily exceed 50 °C (122 °F).
• In damp or dusty locations
• Locations where the unit may be exposed to rain
• Locations subject to violent vibration
• Close to radio or TV transmitters producing strong
electromagnetic fields.
Viewfinder
• Do not leave the camera with the eyepiece pointing
directly at the sun.
The eyepiece lens can concentrate the sun's rays and
melt the interior of the viewfinder.
• Do not use the viewfinder close to strong magnetic
fields. This can cause picture distortion.
Shipping
Use the optional LC-421 Carrying Case for optimal
shipping.
If sending the camera by truck, ship, air or other
transportation service, first store it in the carrying case,
then pack the carrying case in the supplied carton (or
an equivalent).
Care of the unit
Remove dust and dirt from the surfaces of the lenses or
optical filters using a blower.
If the body of the camera is dirty, clean it with a soft,
dry cloth. In extreme cases, use a cloth steeped in a
little neutral detergent, then wipe dry. Do not use
organic solvents such as alcohol or thinners, as these
may cause discoloration or other damage to the finish
of the unit.
In the event of operating problems
If you should experience problems with the unit,
contact your supplier or Sony service representative.

Characteristics of CCD Sensors

The following effects may appear in the image. They
are characteristic of cameras using CCDs (charge-
coupled devices), and do not indicate a malfunction.
Vertical smear
When shooting a very bright object, such as a light, the
highlight tends to produce vertical tails. This effect is
much reduced in this camera.
Vertical tail on the image
Monitor screen
Bright object
(electric light, sun,
etc.)
White flecks
If the camera is operated at a high temperature, white
flecks may appear in the image.
85
Appendix