Sony DXC-D30WSP Service Manual page 18

Location and Function of Parts
@º ZEBRA switch
Set this switch to the ON position to display a zebra
pattern (diagonal stripes) in the viewfinder.
Depending on the zebra setting in advanced menu page
4, the zebra 1 for video levels between 70 to 90 IRE
(or 70 to 90%) and the zebra 2 for video levels 100
IRE or more (or 100% or more) can be displayed
independently or simultaneously.
Front view
1 MIC (microphone) IN +48 V connector (XLR 3-
pin, female)
Connect the supplied microphone or an optional
microphone (operable with a 48 V supply).
2 VF (viewfinder) connector (20-pin)
This is the connector for the DXF-701/701CE
viewfinder.
Note
When using this connector, do not connect a DXF-
40B/50B (or DXF-40BCE/50BCE) viewfinder to the
VF connector on the left side.
14
Chapter 1 Overview
@¡ UP/ON button
Use this button to open displays and to make "ON"
settings. When using the advanced menus, use this
button to change menu pages or to switch to the
ordinary screen display.
@™ DOWN/OFF button
Use this button to close displays and to make "OFF"
settings. You can also use this button to change menu
pages when using the advanced menus.
1 MIC IN +48 V connector
2 VF connector
3 MIC LOW CUT switch
4 FILTER control
5 Lens mount
6 SHUTTER switch
7 TAKE button
8 AUDIO LEVEL knob
9 WHT/BLK switch
0 VTR button
3 MIC LOW CUT switch
Set this switch to the ON position to insert a high-pass
filter in the microphone circuit, reducing wind noise.
Normally leave the switch in the OFF position.
4 FILTER control
Select the color temperature conversion filter
appropriate to the lighting conditions. (See page 39.)
5 Lens mount
Attach the zoom lens here.
6 SHUTTER switch
Use this switch to set the shutter speed, CLS (clear
scan), or EVS setting (see page 75). Usually, set this
switch to OFF.
7 TAKE button
Press this button to specify an editing point (Mark IN/
OUT or cue point) at the current tape position during
shooting.
Left and upper view
1 Fitting for optional microphone holder
You can fit an optional CAC-12 Microphone Holder
here. (See page 29.)
2 Accessory fitting shoe and screw hole
Attach optional video lights or other accessories here.
3 Shoulder strap fixture
To use the supplied shoulder strap, fix one end here
and the other end to the VTR.
8 AUDIO LEVEL knob
When the DSR-1/1P is attached, you can use this knob
to manually adjust the channel 1 audio recording level.
9 WHT/BLK (white/black) switch
This switch is used for automatic adjustment of the
white balance and black balance. (See pages 71 to 74.)
0 VTR button
Pressing this button starts and stops recording on the
VTR.
1 Fitting for optional microphone holder
2 Accessory fitting shoe and screw hole
3 Shoulder strap fitting
4 Viewfinder fitting shoe
5 Viewfinder left-to-right positioning ring
6 Viewfinder front-to-back position locking lever
7 REMOTE connector 1
8 MONITOR OUT connector
9 VIDEO OUT connector
0 REMOTE connector 2
!¡ LENS connector
!™ VF connector
!£ VTR connector
4 Viewfinder fitting shoe
Fix the DXF-701/701CE Viewfinder here.
5 Viewfinder left-to-right position fixing ring
Loosen this ring to adjust the left-to-right position of
the viewfinder. (See page 28.)
6 Viewfinder front-to-back position locking catch
Release this catch to adjust the front-to-back position
of the viewfinder. (See page 28.)
15
Chapter 1 Overview