Related Manuals for Compaq TFT1701
Summary of Contents for Compaq TFT1701
-
Page 1: Compaq Tft1701 Flat Panel Monitor
User’s Guide Compaq TFT1701 Flat Panel Monitor Document Part Number: 304323-001 August 2002... - Page 2 The information in this document is provided “as is” without warranty of any kind and is subject to change without notice. The warranties for HP products are set forth in the express limited warranty statements accompanying such products. Nothing herein should be construed as constituting an additional warranty.
-
Page 3: Table Of Contents
Product Features Safety and Maintenance Guidelines Important Safety Information..... . 2–1 Maintenance Guidelines......2–2 Setting Up the Monitor Removing the Monitor Base . - Page 4 Specifications Compaq TFT1701 Flat Panel Monitor....B–1 Display Resolutions ......B–2 Agency Regulatory Notices Federal Communications Commission Notice.
-
Page 5: Product Features
Your flat panel monitor has an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). The monitor features include: 17-inch (43.18 cm) viewable area display. 1280 x 1024 resolution, plus full-screen support for lower resolutions. Wide viewing angle to allow viewing from a sitting or standing position, or moving side-to-side. -
Page 6: Safety And Maintenance Guidelines
Important Safety Information A power cord is included with your monitor. If another cord is used, use only a power source and connection appropriate for this monitor. For information on the correct power cord set to use with your monitor, refer to the “Power Cord Set Requirements” section in Appendix C of this guide. -
Page 7: Maintenance Guidelines
Adjust only those controls that are covered in the operating instructions. If your monitor is not operating properly or has been dropped or damaged, contact your HP authorized dealer, reseller, or service provider. Adjust only those controls that are discussed in the operating instructions. - Page 8 Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or covered. Never push objects of any kind into cabinet slots or other openings. Do not drop your monitor or place it on an unstable surface. Do not allow anything to rest on the power cord.
-
Page 9: Setting Up The Monitor
Before setting up the monitor, ensure that power is turned off to the monitor, computer system, and other attached devices, then follow these steps: 1. Place the monitor in a convenient, well ventilated location near your computer. 2. Connect the power cord 1 for your monitor to the power port on the rear of the monitor. - Page 10 Setting Up the Monitor 5. Connect the computer’s power cable to an electrical outlet. 6. Turn on your computer and monitor. If your monitor displays an image, installation is complete. Å WARNING: To reduce the risk of electric shock or damage to your equipment: Do not disable the power cord grounding plug.
-
Page 11: Removing The Monitor Base
Removing the Monitor Base The monitor base is removable, which allows flexible mounting solutions. If you choose to mount the monitor onto a swing arm or other mounting fixture, use the following steps to remove the base from the monitor. Ä... -
Page 12: Attaching A Wall-Mount Base
Setting Up the Monitor Attaching a Wall-Mount Base ✎ This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad. 1. Remove the monitor base. Refer to “Removing the Monitor Base” steps in the previous section. 2. Align the mounting interface pad with the holes in the rear cover mounting pad. -
Page 13: Operating The Monitor
2. When the CD-ROM menu launches, select Install INF and ICM Files and follow the on-screen instructions. ✎ To get the latest .INF and .ICM files, download them from the HP Web site at www.hp.com/go/support to download the appropriate files. -
Page 14: Front Panel Components
Operating the Monitor Front Panel Components Component Auto button Exit button Adjust buttons Menu button Power button For energy conservation, turn your monitor off when it is not needed or when leaving it unattended for long periods. Refer to your computer manual for instructions on setting energy saver features (sometimes called power management features). -
Page 15: Rear Components
Rear Components Component Power port connector Signal cable connector User’s Guide Operating the Monitor Function Connects the monitor power cord. Connects the signal cable. 4–3... -
Page 16: Using The On-Screen Display
Operating the Monitor Using the On-Screen Display 4–4 Button Function Exit Use the Exit button to close the active menu or the OSD. + and - Use the adjustment buttons to highlight and adjust items using the OSD. These buttons are also direct access buttons for the brightness feature. - Page 17 The On-Screen Display (OSD) adjusts the screen image based on your viewing preferences. To access the OSD: 1. Press the Power button to turn on the monitor, if the monitor is not already on. 2. Press the Menu button to display the On-Screen Display menu.
-
Page 18: Using The Osd Menu
Operating the Monitor Using the OSD Menu Your OSD menu has the following feature settings. Use the + or - buttons to adjusts the OSD menu functions. Menu Brightness Contrast 4–6 Function Adjusts the screen brightness. When the OSD is not on the screen, press the + or - button to adjust brightness. - Page 19 Menu Image Lock Position User’s Guide Function Use to fine tune and get the best image by removing noises that create unstable images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment, select the Coarse adjustment, and then the Fine adjustment again.
- Page 20 Operating the Monitor Menu Reset Color Temperature 4–8 Function Use to reset the geometry and color parameters. These parameters are replaced with the factory default values. If you don’t want to reset your monitor, use the - adjust button to select No. Use to adjust the color temperature and color control.
- Page 21 Menu Color Control Language User’s Guide Function Use to individually adjust to the red, green, and blue screen colors of the display. Use to change the language used in the menu. You can choose one of seven languages: English, French, German, Italian, Russian, Spanish, Swedish.
- Page 22 Operating the Monitor Menu Menu Halftone Menu Position 4–10 Function Use to make the OSD menus transparent. Use to change to the horizontal or vertical position where the OSD menu appears on your monitor. User’s Guide...
- Page 23 Menu Menu Display Time Use to set the amount of time the OSD Display Mode User’s Guide Function menu will wait before turning off if no adjustments are made. Use to see the frequency, the polarity of the operational signals and the resolution level.
-
Page 24: Monitor Messages
Operating the Monitor Menu Auto Adjustment Monitor Messages Special messages will appear on the monitor screen to identify the following monitor conditions: Video mode not supported - If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator light is still on. -
Page 25: Energy Saver Feature
Energy Saver Feature When the monitor is in its normal operating mode, the monitor utilizes less than 40 watts of power and the Power light is green. The monitor also supports a reduced power state. The reduced power state will initiate if the monitor detects the absence of either the horizontal sync signal and/or the vertical sync signal. -
Page 26: User Modes
Operating the Monitor User Modes The video controller signal may occasionally require a mode that is not preset if: You are not using a Compaq standard graphics adapter. You are not using a preset mode. If this occurs, you may need to readjust the parameters of the monitor screen by using the on-screen display. -
Page 27: Troubleshooting
Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommended solutions. Problem Screen is blank. Image appears blurred, indistinct, or too dark. User’s Guide Troubleshooting Possible Cause Power cord is disconnected. Power switch is off. Video cable is improperly connected. - Page 28 Troubleshooting Problem Image is not centered. “Check Signal Cable” is displayed on screen. “Video Mode Not Supported” is displayed on screen. Monitor is overheating. A–2 Possible Cause Position may need adjustment. Monitor video cable is disconnected. Video resolution and/or refresh rate are set higher than what your monitor supports.
-
Page 29: Using The Worldwide Web
Using the Worldwide Web Before contacting customer services, refer to the support web site http://www.hp.com/go/support Preparing to Call Technical Support If you cannot solve a problem using the troubleshooting tips in this section, you may need to call technical support. Have the... -
Page 30: Specifications
Compaq TFT1701 Flat Panel Monitor Technical Specifications Display Type Viewable Image Size Face Treatment Maximum Weight (Unpacked) Dimensions Height Depth Width Maximum Graphics Resolution Text Mode Dot Pitch Horizontal Frequency Vertical Frequency User’s Guide Specifications 17 inches a-si flat panel, active... -
Page 31: Display Resolutions
Specifications Technical Specifications (Continued) Environmental Requirements Temperature (Independent of Altitude) Operating Temperature Storage Temperature Humidity (Noncondensing) Operating Nonoperating Power Source Power Consumption Input Terminals Display Resolutions The display resolutions listed below are the most commonly used modes and are set as factory defaults. This monitor automatically recognizes these preset modes and they will appear properly sized and centered on the screen. - Page 32 Factory Preset Display Modes (Continued) Pre- Pixel Format 800 x 600 37.879 800 x 600 48.077 800 x 600 46.875 832 x 600 49.726 1024 x 48.363 1024 x 56.476 1024 x 60.023 1152 x 1280 x 1024 1280 x 1024 User’s Guide Horz...
-
Page 33: Agency Regulatory Notices
Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 34: Modifications
Agency Regulatory Notices Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. -
Page 35: Canadian Notice
Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European... -
Page 36: Japanese Notice
Agency Regulatory Notices Japanese Notice Korean Notice EPA Energy Star Compliance Monitors that are marked with the Energy Star Logo meet the requirements of the EPA Energy Star program. As an Energy Star Partner, Hewlett-Packard Company has determined that this product meets the Energy Star guidelines for energy efficiency. -
Page 37: Power Cord Set Requirements
18AWG, and the length of the cord must be between 6 feet (1.8 m) and 12 feet (3.6 m). If you have questions about the type of power cord to use, contact your HP authorized service provider. A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. -
Page 38: Tco '99
TCO ‘99 You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. -
Page 39: Why Do We Have Environmentally Labelled Computers
TCO ‘99 Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. - Page 40 TCO ‘99 The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy.
-
Page 41: Environmental Requirements
TCO ‘99 Environmental Requirements Flame Retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. -
Page 42: Cadmium
Cadmium Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. -
Page 43: Cfcs (Freons
TCO ‘99 CFCs (Freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g.