10/100/1000 Ports; Poe Ports - Cisco Catalyst 2960 Hardware Installation Manual

Hide thumbs Also See for Catalyst 2960:
Table of Contents

Advertisement

Chapter 1
Product Overview
You can use the mdix auto interface configuration command in the command-line interface (CLI) to
enable the auto-MDIX feature. When the auto-MDIX feature is enabled, the switch detects the required
cable type for copper Ethernet connections and configures the interfaces accordingly. Therefore, you can
use either a crossover or a straight-through cable for connections to a copper 10/100/1000 or
1000BASE-T SFP module port on the switch, regardless of the type of device on the other end of the
connection. For configuration information for this feature, see the switch software configuration guide
or the switch command reference.

10/100/1000 Ports

You can set the 10/100/1000 ports to operate at 10, 100, or 1000 Mb/s in full-duplex or half-duplex
mode. You can also set these ports for speed and duplex autonegotiation. (The default setting is
autonegotiate.) When you set the port for autonegotiation, it senses the speed and duplex settings of the
attached device and advertises its own capabilities. If the connected device also supports
autonegotiation, the switch port negotiates the best connection (that is, the fastest line speed that both
devices support and full-duplex transmission if the attached device supports it) and configures itself
accordingly. In all cases, the attached device must be within 328 feet (100 meters).
100BASE-TX and 1000BASE-T traffic requires a Category 5 or higher cable. 10BASE-T traffic can use
Category 3 or Category 4 cables.
When you connect the switch to workstations, servers, routers, and Cisco IP Phones, be sure that the
cable is a straight-through cable. When you connect the switch to switches or hubs, use a crossover cable.
When using a straight-through or crossover cable for 1000BASE-T connections, be sure to use a twisted
four-pair, Category 5 or higher cable for proper operation. Pinouts for the cables are described in
Appendix A, "Connector and Cable Specifications."
You can use the mdix auto interface configuration command in the CLI to enable the automatic
medium-dependent interface crossover (auto-MDIX) feature. When the auto-MDIX feature is enabled,
the switch detects the required cable type for copper Ethernet connections and configures the interfaces
accordingly. Therefore, you can use either a crossover or a straight-through cable for connections to a
copper 10/100/1000 or 1000BASE-T SFP module port on the switch, regardless of the type of device on
the other end of the connection. For configuration information for this feature, see the switch software
configuration guide or the switch command reference.

PoE Ports

This section applies only to the Catalyst 2960-24PC-L and Catalyst 2960 24LT-L switches.
Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if
Warning
interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.
Avoid using such interconnection methods, unless the exposed metal parts are located within a
restricted access location and users and service people who are authorized within the restricted
access location are made aware of the hazard. A restricted access area can be accessed only through
the use of a special tool, lock and key or other means of security. Statement 1072
The 10/100 ports on the Catalyst 2960-24PC-L and ports 1 to 8 of the 10/100 ports on the
Catalyst 2960-24LT-L switches provide PoE support for devices that are compliant with IEEE 802.3af.
The Cisco prestandard PoE is also supported for Cisco IP Phones and Cisco Aironet Access Points.
Each of the Catalyst 2960-24PC-L switch 10/100 ports and ports 1 to 8 on the Catalyst 2960-24LT-L
switch deliver 15.4 W of PoE.
OL-7075-05
Catalyst 2960 Switch Hardware Installation Guide
Front Panel Description
1-9

Advertisement

Table of Contents
loading

Table of Contents