Related Manuals for GE Security GE-DSG-8 DSGH-5
Summary of Contents for GE Security GE-DSG-8 DSGH-5
- Page 1 Security GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual P/N 1069175 • REV 1.01 • ISS 03MAR10...
- Page 2 Disclaimer The information in this document is subject to change without notice. GE Security, Inc. (“GE Security”) assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document.
-
Page 3: Table Of Contents
Switch Operation 15 Address Table 15 Learning 15 Forwarding & Filtering Store-and-Forward Auto-negotiation Chapter 5 Troubleshooting 19 Appendix A Network Connection 21 Switch's RJ-45 Pin Assignments 21 RJ-45 Connector pin assignment 22 GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... - Page 4 GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual...
-
Page 5: Introduction
Introduction GE-DSGH-5 GE-DSGH-8 GE-DSG-8 The GE Security GE-DSG/DSGH series is a 5 and 8-Port 10/100/1000Mbps Industrial Gigabit Ethernet Switch with non-blocking wire-speed performance and new slim type IP 30 metal shape for easy deployment in Heavy Industrial demanding environments. Package Contents Check the contents of your package for following parts: •... -
Page 6: How To Use This Manual
Contains cable information for the Industrial Gigabit Ethernet Switch Product Features Physical Port • 5-Port 10/100/1000Base-T RJ-45 with auto MDI/MDI-X function (GE-DSGH-5) • 8-Port 10/100/1000Base-T RJ-45 with auto MDI/MDI-X function (GE-DSG-8 / GE- DSGH-8) Layer 2 Features • Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T Ethernet standard •... - Page 7 • 12 to 48V DC, redundant power with polarity reverse protect function and connective removable terminal block for master and slave power • -10 to 60 Degree C operating temperature on MC-4TX1FXMM-2km / MC- 4TX1FXSM-15KM / MC-4TX2FX GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual...
-
Page 8: Product Specifications
5% ~ 95% (non-condensing) Standards Conformance IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet Standards Compliance IEEE 802.3ab Gigabit Ethernet IEEE 802.3x Full-duplex flow control IEC60068-2-32 (Free fall), Stability testing IEC60068-2-27 (Shock), IEC60068-2-6 (Vibration) GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... -
Page 9: Installation
Please read this chapter completely before continuing. Product Description The GE Security GE-DSGH-5 and the GE-DSGH-8 are 5/8-Port 10/100/1000Mbps Industrial Gigabit Ethernet Switches with non-blocking wire-speed performance with a new slim type with IP 30 metal shape for easy deployment in Heavy Industrial demanding environments. -
Page 10: Switch Front Panel
Chapter 2: Installation Product Overview The GE Security Industrial Gigabit Ethernet Switch with 5/8 RJ-45 10/100/1000Mbps ports for high-speed network connectivity. The Industrial Gigabit Ethernet Switch can also automatically identify and determine the correct transmission speed and half / full duplex mode of the attached devices with its 5/8 ports. The Gigabit port with 9K jumbo frame feature supported, can handle extremely large amounts of data transmission in a secure topology linking to a backbone or high-power servers. -
Page 11: Led Indicators
Ethernet Switch is used for two DC redundant powers input. Please follow the steps below to insert the power wire. 1. Insert positive / negative DC power wires into the contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2. GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... - Page 12 2. Tighten the wire-clamp screws for preventing the wires from loosing. Figure 3: Terminal Block Power 1 Fault Power 2 Note: The wire gauge for the terminal block should be in the range between 12 ~ 24 AWG. GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual...
-
Page 13: Wiring The Fault Alarm Contact
AWG. Alarm relay circuit accepts up to 30V, max. 3A currents. Figure 5: Alarm schematic Industrial Switch The cloesd circuit will poen when the failure occurs. Fault Alarm Contact 3 & 4 GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... -
Page 14: Mounting Installation
Please read the following topics and perform the procedures in the order being presented. Note: In the installation steps below, this Manual use IGS-801 (GE Security 8 Port Industrial Gigabit Switch) as an example. However, the steps for GE Security Industrial Switch & Industrial Media Converter are similar. - Page 15 3. Check that the DIN-Rail is tightly secured on the track. 4. Please refer to following procedures to remove the Industrial Gigabit Ethernet Switch from the track. 5. Lightly press the button of DIN-Rail for remove it from the track. GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual...
- Page 16 4. Use the hook holes at the corners of the wall mount plate to hang the Industrial Gigabit Ethernet Switch on the wall. 5. To remove the wall mount plate, reverse the steps above. GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual...
-
Page 17: Application
Chapter 3 Application In this section, we will describe how to install the Industrial Gigabit Ethernet Switch into a typical application environment GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... -
Page 18: Installation Steps
Be sure the connected network devices support MDI/MDI-X. If it does not support then use the crossover category 5 Cable. 7. When all connections are all set and LED lights all show normal, the installation is complete. GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... -
Page 19: Switch Operation
If found, and the destination address is located at a different port from where this packet comes in, the Industrial Fast Ethernet Switch will forward this packet to the port where this destination address is located, according to the GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... -
Page 20: Store-And-Forward
10Base-T and 100Base-TX devices can connect with the port in either Half- or Full-Duplex mode. GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... - Page 21 Chapter 4: Installation GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual...
-
Page 22: Troubleshooting
Check per port LED on the Industrial Gigabit Ethernet Switch. Try another port on the Industrial Gigabit Ethernet Switch Make sure the cable is installed properly Make sure the cable is the right type Turn off the power. After a minnute, turn on the power again. GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... -
Page 23: Chapter 5 Troubleshooting
Check per port LED on the Industrial Gigabit Ethernet Switch. Try another port on the Industrial Gigabit Ethernet Switch Make sure the cable is installed properly Make sure the cable is the right type. Turn off the power. After a while, turn on power again GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... -
Page 24: Appendix A Network Connection
Appendix A Network Connection Switch's RJ-45 Pin Assignments 1000Mbps, 1000Base-T Contact MDI-X BI_DA+ BI_DB+ BI_DA- BI_DB- BI_DB+ BI_DA+ BI_DC+ BI_DD+ BI_DC- BI_DD- BI_DB- BI_DA- BI_DD+ BI_DC+ BI_DD- BI_DC- GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... -
Page 25: Rj-45 Connector Pin Assignment
The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual... - Page 26 Appendix A: Network Connection Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network. GE-DSG-8 DSGH-5 and 8 Ethernet Switch User Manual...