Measuring - Makita LS1016 Instruction Manual

When performing compound cutting, refer to "Press
cutting", "Slide cutting", "Miter cutting" and "Bevel
cut" explanations.
6. Cutting crown and cove moldings
Crown and cove moldings can be cut on a
compound miter saw with the moldings laid flat on
the turn base.
There are two common types of crown moldings
and one type of cove moldings; 52/38° wall angle
crown molding, 45° wall angle crown molding and
45° wall angle cove molding. See illustrations.
52 45
38 45
1 2
001555
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((1) and (2) in Fig.
A) and "Outside" 90° corners ((3) and (4) in Fig. A).
(1) (2) (3) (4)
1 2
Fig.A
001556
1
(2)
(1)
(4)
(2)
(3)
(1)
(2)
(1)
001557

Measuring

Measure the wall length and adjust workpiece on
table to cut wall contact edge to desired length.
Always make sure that cut workpiece length at the
back of the workpiece is the same as wall length.
Adjust cut length for angle of cut. Always use
several pieces for test cuts to check the saw
angles.
When cutting crown and cove moldings, set the
bevel angle and miter angle as indicated in the
1. 52/38 ﾟ type
crown molding
2. 45 ﾟ type crown
molding
45
3. 45 ﾟ type cove
45
molding
3
1. Inside corner
2. Outside corner
1. Inside corner
2. Outside corner
(1)
(2)
2
(1)
(2)
table (A) and position the moldings on the top
surface of the saw base as indicated in the table
(B).
In the case of left bevel cut
Molding
position in
Fig. A
(1)
For inside
corner
(2)
(3)
For outside
corner
(4)
006361
Molding
position in
Fig. A
(1)
For inside
corner
(2)
For
(3)
outside
corner
(4)
006362
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to
•
33.9° LEFT.
Adjust and secure miter angle setting to
•
31.6° RIGHT.
Lay crown molding with its broad back
•
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
The finished piece to be used will
•
always be on the LEFT side of the blade
after the cut has been made.
In the case of right bevel cut
Molding
position in
Fig. A
(1)
For inside
corner
(2)
(3)
For outside
corner
(4)
006363
16
Table (A)
Bevel angle
52/38° type 45° type 52/38° type
Right 31.6°
Left 33.9° Left 30° Left 31.6°
Right 31.6°
Table (B)
Molding edge against
guide fence
Ceiling contact edge should
be against guide fence.
Wall contact edge should be
against guide fence.
Ceiling contact edge should
be against guide fence.
Table (A)
Bevel angle
52/38° type 45° type 52/38° type
Right 31.6°
Right 33.9° Right 30° Left 31.6°
Right 31.6°
Miter angle
45° type
Right 35.3°
Left 35.3°
Right 35.3°
Finished piece
Finished piece
will be on the
Left side of
blade.
Finished piece
will be on the
Right side of
blade.
Miter angle
45° type
Right 35.3°
Left 35.3°
Right 35.3°