Honeywell ADEMCO VISTA-40 Programming Manual page 15

PROMPT
10 INPUT S/N: L
A XXX-XXXX -
ÄÄÄÄÄÄÄ
10 INPUT S/N: L
A022-4064 1
10 INPUT S/N: L
A000-0000 1
XMIT TO CONFIRM
PRESS ✱TO SKIP
Entd A022-4063 1
Rcvd A022-4064
Zn ZT P RC In L
11 00 1 10 00 1
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
Entering Wireless Keys
If you pressed the D key previously to enter defaults for 5804 and/or 5804BD wireless keys, the following screens appear:
PROMPT
FROM TEMPLATE
1–6 1
L 01 02 03 04
ZT 23 22 21 23 1
EXPLANATION
If you entered RF, BR, UR or SL for the Input Type, this screen displays. Otherwise the summary screen for
the next zone displays.
Enter the 7-digit serial number, using one of the following methods:
a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and
release the button, wait approximately 4 seconds, then press and release the button a second time.
OR
b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the alpha keypad.
Then press the [✱] key, the cursor will move to the "L" position. You can edit the loop number, if
necessary. When the loop number is acceptable, press [✱].
OR
c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several
input loops).
Remember, you can use the [A] key to move to the right or the [B] key to move to the left.
You can also use the [#] key to back up without saving.
Press [✱] to accept the serial number and advance to the "L" position (if method "a" or "c" was used), then
enter the loop number.
If necessary, press the [#] key to back up without saving, and re-enter or edit the serial number before
pressing [✱] to save
The system checks for a duplicate. If a duplicate serial/loop number combination is found, the keypad will
emit a single long beep, and display the serial number along with a "?" for the loop number, allowing you to
re-enter the correct loop number.
To Delete an Existing Serial Number, enter 0 in the loop number field. The serial number will change to
"0"s.
If 0 was entered in error, simply re-enter the loop number or press [#], and the serial number will return to the
display.
The prompt to confirm appears. This prompt only appears if you answered "Yes" at the "SET TO
CONFIRM?" prompt.
The system enters a confirmation mode so that the operation of the actual programmed input can be
confirmed. Activate the loop input or button that corresponds to this zone. At any time during this step, you
may press the [✱] key on the keypad to save the serial and loop number combination without confirming.
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it also is displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display for the next zone does not appear), press the [#] key twice and then enter or transmit the correct
serial number.
Activate the button on the wireless key again after re-entering the serial number.
If the serial number transmitted matches the serial number entered, the system beeps 3 times and
advances to the summary display for the next zone's programming.
After all the zones have been programmed, enter 00 for the zone number to quit.
EXPLANATION
Enter template number (1–6).
1–3 = 5804 templates; 4–6 = 5804BD templates. See the defaults provided for each template in the chart
that follows these procedures.
Select from templates. Press [✱] to display template (template 1 shown selected).
Note: If necessary, press [#] to back up and re-enter template number.
Press [#] if you want to return to zone attributes screen.
When you press [✱], the selected template is displayed.
Top line of display represents loop numbers; bottom line represents zone type.
Press [✱] to accept template.
– 15 –