5800 Series Transmitters Loop Designations - Honeywell ADEMCO VISTA-40 Programming Manual

5800 Series Transmitters Loop Designations

5 8 0 1
ENROLL AS "UR" OR "RF"
YOU MUST
ENROLL THIS
BUTTON
LOOP 4
5 8 0 4
ENROLL
AS "BR"
5809
ENROLL AS "RF"
5808
ENROLL AS "RF"
Note: For information on any transmitter not shown above, refer to the instructions accompanying that transmitter for
details regarding loop numbers, etc.
The 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, 5827BD,
U L
and 5850 transmitters are not intended for use in UL installations.
PROMPT
XMIT TO CONFIRM
PRESS ✱TO SKIP
Entd A022-4063 1
Rcvd A022-4064
10 ZT P RC In L
03 1 3C RF 1s
LOOP 3
LOOP 2
LOOP 1
LOOP 4
YOU MUST
ENROLL THIS
BUTTON
5 8 0 2 M N
ENROLL AS "UR" OR "RF"
LOOP 3
LOOP 2
LOOP 1
LOOP 2
YOU MUST
ENROLL THIS
BUTTON
LOOP 4
LOOP 1
LOOP 3
•
• •
• • •
SET
• • • •
• •
•
• HOUSE
CODE
5 8 0 4 B D
ENROLL AS "BR"
LOOP
1
LOOP 2
(REED)
LOOP
1
LOOP 1
(TERMINALS)
5 8 1 6
ENROLL AS "RF"
EXPLANATION
Confirmation Option: This prompt only appears if you answered "Yes" at the first prompt. The system
enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate
the loop input or button that corresponds to this zone. At any time during this step, you may press the [✱] key
on the keypad to save the serial and loop number combination without confirming.
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it is also displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key twice and then enter or transmit the correct serial number.
If the serial number transmitted does match the serial number entered, the system beeps 3 times and a
summary display appears, showing that zone's programming. Note that an "s" indicates that a transmitter's
serial number has been enrolled.
Press [✱] to accept the zone information.
LOOP 2
(REED)
LOOP 1
LOOP
(TERMINALS)
1
ALTERNATE
POSITION
5 8 1 6 M N
FOR LOOP 2
ENROLL AS "RF"
LOOP
LOOP 1
2
(TERMINALS)
(REED)
LOOP 3
(TERMINALS)
5 8 1 9
ENROLL AS "RF"
5 8 2 7
SET HOUSE CODE
(Green)
(Red)
(Yellow)
5 8 5 0 ( G B D )
ENROLL AS "RF"
– 13 –
LOOP 1
(PRIMARY)
LOOP 2
(AUX. CENTER)
LOOP 3
(AUX. RIGHT)
5 8 1 7
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 1
LOOP 3 (INTERNAL
(TERMINALS) SHOCK
SENSOR)
5 8 1 9 S ( W H S & B R S )
ENROLL AS "RF"
5 8 2 7 B D
SET HOUSE CODE
LOOP 1
(MOTION)
5 8 9 0
ENROLL AS "RF"
5800_trans_loop-V0