Samsung SCX-812x Series User Manual page 147

Message Meaning
Fusing unit is not The fuser unit you
compatible. Check have installed is not
user's guide. for your machine.
Fuser unit is not The fuser unit is not
installed correctly. properly installed.
Install it.
HDD is almost HDD is almost full in
full-1. Check user's the machine.
guide.
HDD is almost HDD is almost full in
full-2. Check user's the machine.
guide.
HDD is almost HDD is almost full in
full-3. Check user's the machine.
guide.
HDD is almost HDD is almost full in
full-4. Check user's the machine.
guide.
HDD is almost HDD is almost full in
full-5. Check user's the machine.
guide.
HDD is almost HDD is almost full in
full-6. Check user's the machine.
guide.
HDD System There is a problem in
Failure [error the hard disk.
number]:Turn off
then on.
Suggested solutions
Install a
Samsung-genuine fuser
unit, designed for your
machine, call for service.
Reinstall the fuser unit. If
the problem persists, call
for service.
Check Address Book or
User Profile. If
necessary, remove the
data which is unused in
Address Book or User
Profile.
Check Stored
Document, or Secured
Job in Job Status. If
necessary, remove the
data which is unused in
Stored Document or
Secured Job.
Check System Log at
Security in SyncThru™
Web Service. If
necessary, remove the
data in System Log.
• Print or remove the
jobs on the queue
which are waiting for
its turn. You can check
the jobs pressing Job
Status (see "Job
Status button" on
page 36).
• Print or remove the
received fax jobs in
Secure Receive (see
"Receiving in secure
receiving mode" on
page 70).
There is a problem in the
machine. Check the error
message on the display
screen and resolve the
problem.
There is a problem in the
machine. Check the error
message on the display
screen and resolve the
problem.
Turn the machine off and
back on again. If the
problem persists, call for
service.
Troubleshooting_ 147
Message Meaning
Input System There is a problem in
Failure [error the tray.
number]:Pull [tray
number] out and
insert it.
Image transfer belt The image transfer
cleaning unit is not belt cleaning unit you
compatible. Check have installed is not
user's guide. for your machine.
Image transfer belt The image transfer
unit is not original belt you have installed
Samsung. Check is not for your
user's guide. machine.
ITB Unit Failure There is a problem in
[error the image transfer belt
number]:Turn off unit.
then on.
MSOK System There is a problem in
Failure [error the engine system.
number]:Turn off
then on.
Network cable is The machine is not
disconnected. connected with a
Check it. network cable.
Option Feed door The door is not
is opened. Close it. securely latched.
Original paper jam The originals are
in front of scanner jammed in duplex
automatic document
feeder.
Original paper jam The originals are
inside of scanner jammed in duplex
automatic document
feeder.
Output tray(face The output tray (face
down) is full. down) is full.
Remove printed
media
Output tray(face The output tray (face
up) is full. Remove up) is full.
printed media
Paper is empty in There is no paper in
[tray number]. the tray.
Load paper.
Paper is empty in There is no paper in
tray MP. Load the multi-purpose tray.
paper.
Paper is low in Running out of paper
[tray number]. in the tray.
Load paper.
Suggested solutions
Open and close the tray.
If the problem persists,
call for service.
Install a
Samsung-genuine image
transfer belt cleaning
unit, designed for your
machine, call for service.
Install a
Samsung-genuine image
transfer belt, designed for
your machine, call for
service.
Turn the machine off and
back on again. If the
problem persists, call for
service.
Turn the machine off and
back on again. If the
problem persists, call for
service.
Connect the machine to
the network with a
network cable.
Close the door until it
locks into place.
Clear the jam (see
"Original paper jam in
front of scanner" on
page 133).
Clear the jam (see
"Original paper jam inside
of scanner" on
page 134).
Remove papers from the
output tray (face down),
the machine resumes
printing.
Remove papers from the
output tray (face up), the
machine resumes
printing.
Load paper in the tray.
Load paper in the
multi-purpose tray.
Load paper in the tray.