Download  Print this page

List Of Symptoms - Brother 882-C50 Operational Manual

Embroidery and sewing machine.
Hide thumbs

Advertisement

TROUBLESHOOTING

List of Symptoms

Problem
The thread is tangled
Upper threading is incorrect.
on the wrong side of
the fabric.
Using improper needle or thread for the
selected fabric.
The upper thread is
The bobbin thread is incorrectly installed.
too tight.
Cannot thread the
Needle is not in the correct position.
needle
Needle is installed incorrectly.
Needle is turned, bent or the point is dull.
Cannot lower the
Presser foot was raised using the "Presser Foot
presser foot with the
Lifter" button.
presser foot lever
Thread tension is
Upper threading is incorrect.
incorrect
Bobbin is set incorrectly.
Using improper needle or thread for the
selected fabric.
Presser foot holder is not attached correctly.
Thread tension is set incorrectly.
Bobbin thread is incorrectly wound.
Needle is turned, bent or the point is dull.
Upper thread breaks
Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Needle is turned, bent or the point is dull.
There are scratches on the bobbin case.
Upper thread tension is too strong.
Using improper needle or thread for the
selected fabric.
Thread is twisted.
There are scratches near the hole of the needle
plate.
There are scratches near the hole in the presser
foot.
Needle is installed incorrectly.
Thread is knotted or tangled.
A bobbin designed specifically for this machine
is not used.
Bobbin thread breaks Bobbin is set incorrectly.
There are scratches on the bobbin or it doesn't
rotate properly.
Thread is twisted.
A bobbin designed specifically for this machine
is not used.
Bobbin thread does
The thread is not passed through the bobbin
not wind neatly on the
winding thread guide correctly.
bobbin.
Bobbin spins slowly.
The thread that was pulled out was not wound
onto the bobbin correctly.
A-30
Cause
Check the steps for threading the machine
and rethread the machine.
Check the "Fabric/Thread/Needle
Combinations" chart.
Correctly install the bobbin thread.
Press the "Needle Position" button to raise
the needle.
Reinstall the needle correctly.
Replace the needle.
Press the "Presser Foot Lifter" button to
lower the presser foot.
Check the steps for threading the machine
and rethread the machine.
Reset the bobbin. (If needle plate was
removed, reinstall needle plate and tighten
screws prior to installing bobbin case.)
Check the "Fabric/Thread/Needle
Combination" chart.
Reattach the presser foot holder correctly.
Adjust the thread tension.
Use a correctly wound bobbin.
Replace the needle.
Rethread the machine correctly.
Replace the needle.
Replace the bobbin case, or consult your
authorized dealer.
Adjust the thread tension.
Check the "Fabric/Thread/Needle
Combinations" chart.
Use scissors, etc., to cut the twisted thread
and remove it from the race, etc.
Replace the needle plate, or consult your
authorized dealer.
Replace the presser foot, or consult your
authorized dealer.
Reinstall the needle correctly.
Rethread upper and lower thread.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
Reset the bobbin thread correctly.
Replace the bobbin.
Use scissors, etc. to cut the twisted thread
and remove it from the race, etc.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
Correctly pass the thread through the bobbin
winding thread guide.
Press [+] in the bobbin winding window to
increase the bobbin winding speed.
Wind the thread that was pulled off around
the bobbin 5 or 6 times clockwise.
Solution
Page
B-46
B-57
B-43
B-11
B-55
B-55
B-11
B-46
B-43
B-57
B-53
S-12, E-30
B-38
B-55
B-46
B-55
A-19
S-12, E-30
B-57
S-26
B-53
B-55
B-43, B-46
B-43
B-43
B-43
B-43
B-39
B-41
B-40

Advertisement

Table of Contents

   Related Manuals for Brother 882-C50

Comments to this Manuals

Symbols: 0
Latest comments: