Download  Print this page

Connect The Unit (Wps And Manual) - Pioneer AS-WL300 Getting Started Manual

150mbps wireless lan converter
Hide thumbs
   

Advertisement

....---
Please connect using either method.---,
STEP2
Connect the Unit (WPS)
0
e
This procedure explains how to connect the unit using the
WPS
function. If the base does not have a WPS
function.
refer to the
"Manual" procedure below.
e
Do not connect the LAN cable to the unit until instructed.
e
When using multiple units of this product.
the
IP address of this unit
needs to be changed. Refer to "Troubleshooting" on the reverse.
1 . Switch an the unit
0
Switch off the AV device.
AV RECEIVER
Blu-ray Disc player
Connect the
POWER connector
on the unit to the USB port on the
AV device
using the USB end of the supplied feeder cable.
~ITJ
·I
The
location of the USB
port and its name may
vary depending on the
device.
If
you cannot
locate a USB port. refer
to the device's user's
manual for help.
Switch on the AV device.
A USB port
is the
horizontally
Cor vertically) long port
(as shown
above).
*
On some devices.
it
is
labelled
[DC
OUTPUT
for
WIRELESS LAN].
AV RECEIVER
If=
]1
Blu-ray Disc player
AV RECEIVER
Blu-ray Disc
player
Check that
the
"(.!,)(POWER)" ,
"g
(WPS)" and
"~(WIRELESS)"
indicators
on
the
unit are lit.
"'
Once the indicators light up, wait
2 minutes before proceeding.
~
..
,
...
Lit
2. Connect the Unit
0
fJ
Press the "WPS" button on the base.
Refer
to the base
user's
manual
lor more details on the WPS
button.
Press and hold the "WPS" button on
the
back of the unit until the
WPS
indicator
on the front
flashes.
(over 2 seconds).
Press and hold for over 2 seconds
The WPS indicator (centre) will flash
~Q
I
...
...
uo~
Check that the WPS indicator on the unit changes
from a flashing
light
to a steadily lit light.
*
If the WPS indicator stops flashing and is steadily lit.
the unit is connected to the Wireless LAN.
(The unit is not connected if the WPS indicator is
flashing.)
*
If the WPS indicator does not flash. press the "WPS"
button again.
*
If the WPS indicator stops flashing and turns off.
the
~wPS"
button
Disconnect
the USB feeder cable end of the supplied cable
that
is connected to the unit.
-~
- --'1
~~~~=~:
Blu-ray Disc player
Connection
to
the
base
is now complete. Continue to
Step
3.
STEP2
Connect the Unit (Manual)
0
e
Use this procedure to manually connect the unit. especially if connecting
the
unit
using the "WPS" procedure. above. does not work.
e
If
the computer on which you will configure the unit is connected to the
Wireless LAN cable disconnect it.
e
When using multiple units of this product. the IP address of this unit
needs to be changed. Refer to "Troubleshooting" on the reverse.
1 . Search far a Network Connection
Before connecting or configuring this unit, you must know the Wireless LAN
settings for your base. Write the settings in
the
table below.
• Refer to the base user's manual for details on the Wireless LAN settings.
When using WEP security settings
Name
Wireless LAN settings
(1)
SSID (Network name)
(2)
Authentication
O
OPEN
0
SHARED
(3)
Authentication key method
0
Hexadecimal"
1
0
ASCII' 2
(4)
Default key
0
Key
1
0
Key2
0
Key3
0
Key4
(5)
Encryption key
1:
1
&drg
rt number (0-9, A-F)
2. ASCII ( 1-byte letters and numbers. rnc!udrng upper and lowercase
!etters)
When using WPA/WPA2 security settings
Name
Wireless
LAN
Settings
(1)
SSID (Networf< name)
(2)
Authentication
O
WPA-PSK
O
WPA2-PSK
{3)
Authentication key
0
Hexadecimal" 1
0
ASCII' 2
(4)
Encryption
O
TKIP
O
AES
(5)
Encryption key
• 1 : 1 &dreut number (0-9, A-F)
2. ASCII (
1-byte
letters and numbers. rncludrng upper and lowercase letters)
0
This unit cannot connect to a base with
a
SSID (Network name) that Includes a semicolon(;).
Refer
to the base user's manual for details on changing the SSID.
2. Connect to the Computer
o
Switch
ott
the computer.
~
Connect the
ETHERNET port
on the unit to the computer
LAN port
on
the
computer
using the LAN end of the supplied feeder cable.
o[1 .
J
*
The location of the LAN port and its name may vary
depending on the computer. If you cannot locate a LAN
port. refer to the computer user's manual for help.
The
LAN port is the
large port
that is slightly
larger than a telephone modular jack.
• Some bases have LAN written on them.
Connect the
POWER connector
on
the
unit
to
the
USB port
on
the computer using the
USB end of the supplied feeder cable.
*
The location of the USB port and its name may
vary depending on the device. If you cannot
locate a USB port. refer to the device's user's
1
manual for help.
~-9
A
USB port
is
the
horizontally (or vertically) long
port
(as shown
above).
On
some computers. it
is
labelled "USB" or
marked
by a
·~·.
Switch on the
computer.
Check that the"(.!,) (POWER)" .
"g
CWPS)"
and
'9'
(WIRELESS)"
indicators
on the unit are
lit.
Once the indicators light up,
wait
2 minutes before proceeding.
3. Configure the Unit
o
Launch
the
Web
browser.
fJ
Enter "cv.setup"
in
the Address
bar and press <Enter>.
Lit
0
If
you
cannot display the Web Configuration window by entering
~cv.setuo".
enter
"192.168.1.249" and
proceed toiJ.If the window still does not open, refer to
"Troubleshooting~
on
the
reverse.
CD
Enter
"admin" as
the user name
and "password" the password.
®
Click [OK].
0
If
you
camot
log
in
to the
Web
Configuration
window.
check
that
you
have entered the settings, correctly.
,,.._' " "_ . . .u-..u.,.......----
=:---===--=·~-
(~~
)CD
G:).
Continued
over
the page

Hide quick links:

Advertisement

Table of Contents
loading

  Related Manuals for Pioneer AS-WL300