Download Print this page
JBL VRX932LAP/230 Technical Manual

JBL VRX932LAP/230 Technical Manual

Advertisement

Quick Links

Technical Manual
JBL VRX932LAP/230

SPECIFICATIONS

ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• DPC-2 Internal Amplification Output
(at normal load):
• Frequency Response:
• Frequency Range:
• Maximum Peak Output:
• Signal Processing:
• AC Power Operating Range: 90-132 VAC or 216-264 VAC, 50/60Hz
• AC Input Connector:
• AC Loop Through Connector: Neutrik PowerCon (NAC 3MPB)
• Audio Input Connector:
• AC Current Requirements:
• AC Line Voltage:
• System Managerment:
• User Controls:
• DPC-2 Output as (Continuous IEC shaped pink noise into rated load
impedance):
• DPC-2 Output section
SYSTEM COMPONENTS:
PACKAGE
Manual
364536-001
Pad, Filler (2)
364343-001
Filler, Grille
364344-001
Pkg, Microfoam
49790P
JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A.
1750 Watts Peak, 875 Watts Continuous
75 Hz - 20 kHz (±3 dB)
57 Hz - 20 kHz (–10 dB)
136 dB SPL at 1m
DSP based, resident in Input Module
Neutrik PowerCon (NAC 3MPA)
XLR with loop through
6A per system at 120V, 3A per system
at 240V
User selectable:120V/240V (-15%,+10%)
DSP based limiters for mechanical and
thermal protection
Input Attenuator (0-16 dB), ACS Array
Configuration Selector), HF level adjust-
ment (+3 dB, 0 dB, –3 dB)
LF:750 Watts, HF: 125 Watts
LF: Dual-Bridged Technology
(TM)
HF:Bridged Class D

WIRING DIAGRAM

Warranty 59660
Power Cord Assembly
Pack / Edison, Shucko
355040-002
Contents:
355146-001 (120V) (1)
Power Cord
355147-001 (230V) (1)
Power Cord
NAC3FCB (1)
Neutrik
Gray PowerCon
Carton
364342-001
• Cabinet:
• Grille:
• Low Frequency
Transducer:
• Bandpass Nominal
Inpedance:
• DC Resistance:
• High Frequency
Transducer
• Bandpass Nominal
Inpedance:
• DC Resistance:
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 0.8V (Gain fully CCW)
B. L.F. Aural Sweep Test:
C. H.F. Aural Sweep Test:
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions:
,Class D
• Net Weight:
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
BLU/BLK
Driver,
Low Freq
2262FF
(363946-001X)
Cone Repl
C2X2R2262
GRN/BLK
WIRING HARNESS DIAGRAM / SCHEMATIC
364338-004
GRN/BLK
YEL/BLK
BLU/BLK
BLU
YEL
GRN
NOT USED
NOT USED
26.5" YEL/BLK
26.5" YELLOW
20.5"GRN/BLK
20.5" GRN
20.5" BLU/BLK
20.5" BLU
Enclosure (Not For Sale)
352282-001
2262FF, 305 mm (12 in) dual voice coil
Differential Drive
(R)
woofer with neo-
dymium-magnet
2 x 2 ohms
5.1 ohms ± 10%
(3) 2408J, 38 mm (1.5 in) voice coil,
neodymium compression driver
4 ohms
8.9 ohms ± 0.2%
7V Input, 10 Hz to 1 kHz
1.0V Input, 200 Hz to 1.5 kHz
349 x 597 x 444 mm D
(13.75 x 23.5 x 17.5 in. D)
52 lb (24 kg.)
Driver,
BLU
High Freq (3)
2408J
(361549-003X)
Diaph Repl
D16R2408
YEL
Amplifier
Assemby
YEL/BLK
DPC-2
Wire Harness
Assembly
GRN
364338-004
LF-1
LF-2
SCHEMATIC
.250 SERIES,RECEPTABLE/TAB FASTON PIGGYBACK
.187 SERIES,RECEPTABLE/TAB FASTON PIGGYBACK
LF-1
LF-2
08-12

Advertisement

loading

Summary of Contents for JBL VRX932LAP/230

  • Page 1: Specifications

    JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A. Technical Manual JBL VRX932LAP/230 SPECIFICATIONS ACOUSTIC & ELECTRICAL SPECIFICATIONS: • Cabinet: Enclosure (Not For Sale) • Grille: 352282-001 • DPC-2 Internal Amplification Output • Low Frequency 2262FF, 305 mm (12 in) dual voice coil...
  • Page 2 JBL VRX932LAP/230 COMPONENT EXPLODED VIEW Wire Harness Amp Board 364338-004 443941-001 Screw (10) Input Board 804-51110-12 443920-001 10-32 x 3/4 Bolt,Horn (2) OVAL,PH,BLK Modular PCB 854-00000-60 ZINC, LCS 444087-001 1/4-20 X 3 3/4 HEX,CLRZINC,LCS Amplifier Trim Interface PCB Enclosure Assembly...
  • Page 3 JBL VRX932LAP/230 AMPLIFIER ASSEMBLY 363679-004 Amp Board 443941-001 Input Board 443920-001 Modular PCB 444287-001 Interface PCB 443807-001 Label, Model VRX932LAP Screw (4) 364540-002 801-41110-06 4-40 x 3/8 Knob, Volume PAN,PH,CLR, Push Button (2) 364582-001 ZINC,LCS 364386-001 Crown Amp Logo Badge...
  • Page 4 JBL VRX-AF ARRAY FRAME ASSEMBLY Manual 353551-007 • 4” 1/4-20 bolts to horn — 5” — caution! You can break the horn at 60”/lbs, which is prety easy with a ratchet (pull on the end of a 1’ handle with 5 pounds).