Electrical Parts List - Sony DCR-DVD105 Service Manual

CD-600 CK-154

5-2. ELECTRICAL PARTS LIST

Ref. No. Part No. Description
A-1166-585-A CD-600 BOARD, COMPLETE
**********************
(IC6001 is not included in this complete board.)
< CAPACITOR >
C6001 1-104-851-11 TANTAL. CHIP
C6002 1-164-943-81 CERAMIC CHIP
C6003 1-164-943-81 CERAMIC CHIP
C6004 1-113-987-11 TANTAL. CHIP
C6005 1-164-850-11 CERAMIC CHIP
C6006 1-164-943-81 CERAMIC CHIP
< CONNECTOR >
* CN6001 1-816-646-51 FFC/FPC CONNECTOR (LIF) 16P
< IC >
IC6001 8-753-244-70 ICX610NKF-13 (CCD IMAGER)
IC6001 8-753-244-71 ICX611NKF-13 (CCD IMAGER)
< COIL >
L6002 1-469-528-91 INDUCTOR
< TRANSISTOR >
Q6001 8-729-117-73 TRANSISTOR
< RESISTOR >
R6001 1-218-959-11 RES-CHIP
A-1166-570-A CK-154 BOARD, COMPLETE
***********************
< BATTERY >
0 BT6401 1-528-999-61 BATTERY, LITHIUM SECONDARY
< CONNECTOR >
* CN6401 1-817-283-51 CONNECTOR, FPC (ZIF) 51P
CN6402 1-766-338-51 CONNECTOR, FFC/FPC 8P
CN6403 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P
* CN6404 1-818-073-51 CONNECTOR, FFC/FPC (ZIF) 36P
< DIODE >
D6401 8-719-083-91 DIODE EDZ TE61 6.8B
D6403 6-500-776-01 DIODE MAZW068H0LS0
D6404 8-719-083-91 DIODE EDZ TE61 6.8B
D6405 8-719-083-91 DIODE EDZ TE61 6.8B
< RESISTOR >
R6402 1-218-957-11 RES-CHIP
R6403 1-218-960-11 RES-CHIP
R6404 1-218-955-11 RES-CHIP
R6405 1-218-954-11 RES-CHIP
DCR-DVD105/DVD105E/DVD605/DVD605E_L2
Ref. No.
10uF 20% 10V
0.01uF 10% 16V
0.01uF 10% 16V
4.7uF 20% 25V
10PF 0.5PF 50V
0.01uF 10% 16V
(DVD105/DVD605) (Note)
(DVD105E/DVD605E) (Note)
100uH
2SC4178-F14
3.3K 5% 1/16W
2.2K 5% 1/16W
3.9K 5% 1/16W
1.5K 5% 1/16W
1.2K 5% 1/16W
5-12
Part No. Description
< SWITCH >
S6402 1-771-138-82 SWITCH, KEY BOARD (RESET)
S6403 1-771-138-82 SWITCH, KEY BOARD (DISP/BATT INFO)
S6404 1-786-179-11 SWITCH, PUSH (1KEY) (PANEL OPEN/CLOSE)
S6405 1-771-138-82 SWITCH, KEY BOARD (EASY)
Electrical parts list of DD-246 board is not
shown.
Pages 5-13 to 5-14 are not shown.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
Note: Be sure to read "Precaution for Replacement
of Imager" on page 4-1 when changing the
imager.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.