Central Pneumatic 68057 Owner's Manual
  1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Nail Gun
  5. 68057
  6. Owner's manual

Central Pneumatic 68057 Owner's Manual

3-in-1 18/16 gauge air nailer/stapler
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Central Pneumatic 68057

Summary of Contents for Central Pneumatic 68057

  • Page 2: Table Of Contents

    National pipe thread, straight NIOSH-approved dust mask/respirator. WARNING marking concerning WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved Risk of Explosion. safety goggles with side shields. Table A: Symbol Definitions Page 2 For technical questions, please call 1-800-444-3353. Item 68057...

  • Page 3: Work Area

    A dust mask, non-skid safety shoes the tool is able to fire a fastener. and a hard hat must be used for the applicable conditions. Wear heavy- duty work gloves during use. Item 68057 For technical questions, please call 1-800-444-3353. Page 3...

  • Page 4: Tool Use And Care

    Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. SAVE THESE INSTRUcTIONS. Page 4 For technical questions, please call 1-800-444-3353. Item 68057...
  • Page 5 17. Keep clear of the workpiece near the area being fastened. Fasteners may bend sideways during firing, causing them to exit the workpiece at an unexpected point, causing personal injury. Item 68057 For technical questions, please call 1-800-444-3353. Page 5...
  • Page 6 If you feel any symptoms related to vibration (such in this manual. If abnormal vibration occurs, as tingling, numbness, and white or blue fingers), stop immediately. seek medical advice as soon as possible. SAVE THESE INSTRUcTIONS. Page 6 For technical questions, please call 1-800-444-3353. Item 68057...

  • Page 7: Specifications

    Safety Mechanism Type Single Sequential 1" to 2-1/2" 16-gauge Finish Nails Nail Size Range 5/8" to 2" 18-gauge Brad Nails Staple Size 5/8" to 1-1/2" 18-gauge Staples Range Magazine Capacity 100 Fasteners Item 68057 For technical questions, please call 1-800-444-3353. Page 7...
  • Page 8 Latch Knob (33) (73) Safety (37) Safety Nosepiece - Also called the workpiece contact, the Safety Nosepiece helps prevent the tool from firing unless it is pressed against an object. Page 8 For technical questions, please call 1-800-444-3353. Item 68057...

  • Page 9: Setup

    3. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. Item 68057 For technical questions, please call 1-800-444-3353. Page 9...
  • Page 10 Page 10 For technical questions, please call 1-800-444-3353. Item 68057...
  • Page 11 Item 68057 For technical questions, please call 1-800-444-3353. Page 11...

  • Page 12: Operation

    The tool must not cycle (fire). it repaired by a qualified service technician. If it fails to perform in the manner explained in bold, have it repaired by a qualified service technician. Page 12 For technical questions, please call 1-800-444-3353. Item 68057...

  • Page 13: Safety Goggles With Side Shields

    Fixed Magazine. See below. Staples 5. After the nails or staples are loaded, slide the Moveable Magazine back into Fixed Magazine until the Latch snaps back into place, locking the fasteners into place. Item 68057 For technical questions, please call 1-800-444-3353. Page 13...
  • Page 14 Store indoors out of children’s reach. work piece or causing personal injury. Page 14 For technical questions, please call 1-800-444-3353. Item 68057...

  • Page 15: Maintenance

    1. If a fastener is jammed in the discharge 2. Depress the Latch and pull back on the area, remove it with pliers. Moveable Magazine, sliding it down to bottom of Fixed Magazine. Item 68057 For technical questions, please call 1-800-444-3353. Page 15...
  • Page 16 14. If you are unable to clear the fastener jam using the method prescribed above, the tool should be taken to a qualified service technician for proper servicing. Page 16 For technical questions, please call 1-800-444-3353. Item 68057...

  • Page 17: Troubleshooting

    LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 68057 For technical questions, please call 1-800-444-3353. Page 17...

  • Page 18: Parts List And Diagram

    Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 18 For technical questions, please call 1-800-444-3353. Item 68057...
  • Page 19 Assembly Diagram Item 68057 For technical questions, please call 1-800-444-3353. Page 19...

  • Page 20: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents