Honeywell VISIONPRO 68-0287-04 User Manual page 17

ISU
Parameter Installer Setup
Number Name
394 Southern
Dehumidification
Away
Dehumidification
Setting
400 Ventilation control 0
401 Number of
bedrooms
402 Total house
Sq. Ft.
403 Ventilation CFM
404 Max ventilation
percentage limit
405 Ventilation Fan
Action
406 Ventilation in
High Humidity
430 Ventilation
lockout
431 Ventilation
lockout high
temperature
432 Ventilation
lockout low
temperature
450 DATS Inhibit
500 Furnace Filter
USU Change
Reminder
502 Furnace filter
reminder run time
equipment counts
Table 3. Installer Setup Menu. (Continued)
Settings
(Factory Defaults Shown in Bold)
65 Default = 65%
40-70 40%–70% relative humidity
No ventilation
1 Ventilation on at all times
2 Ventilation on except during sleep period
3 Vent all with lockouts
4 Vent off sleep with lockouts
2 Default = 2
1-6 1–6 bedrooms
10 Default = 1000 sq. ft.
10-50 1000–5000 sq. ft. in increments of 100
160 Default = 160 CFM
30-195 30–195 CFM in increments of 5
50 Default = 50%
30-60 30%–60%
100 unlimited
1 Vent on will force fan on also
2 Vent will not force fan ON
1 On
0 Off
0 Disabled
1 Lockout for high temperatures
2 Lockout for low temperatures
3 Lockout for high and low temperatures
100 38 100°F 38°C
90 32 90°F 32°C
95 35 95°F 35°C
105 40.5 105°F 40.5°C
110 43.5 110°F 43.5°C
-10 -23.5 -10°F -23.5°C
-20 -29 -20°F -29.0°C
-15 -26 -15°F -26.0°C
-5 -20.5 -5°F -20.5°C
-0 -18 0°F -18.0°C
0 Disabled
35 1.5 35°F 1.5°C
40 4.5 40°F 4.5°C
45 7 45°F 7.0°C
50 10 50°F 10.0°C
55 13 55°F 13.0°C
60 15.5 60°F 15.5°C
65 18.5 65°F 18.5°C
E Auto Discover
0 Disabled
1 10 R.T. Days
2 30 R.T. Days
3 60 R.T. Days
4 90 R.T. Days
5 120 R.T Days
6 180 R.T. Days
7 270 R.T. Days
8 365 R.T. Days
9 30 C Days
10 60 C Days
11 90 C Days
12 120 C Days
13 180 C Days
14 365 C Days
0 Counts runtime Heat and Cool
1 Counts runtime Cool only
VISIONPRO
Set the desired humidity level to maintain within the
living space
If ISU300 = 0, ISU401-405 will not be shown.
Not ASHRAE
Not ASHRAE
The thermostat will determine if ventilation is
meeting ASHRAE standard 62.2. The display will
show a P above the setup number if the setting
passes the ASHRAE standard, or F if it does not.
Best practice is to move the setting down until F is
displayed, then move up one setting to the minimum
passing value.
Only shown if ISU372 and ISU400 are not set to 0.
When set to On will use ventilation to remove
humidity when thermostat is in the heat mode.
Outdoor temperature sensor required for high and
low temperature lockouts.
The DATS will cycle the cooling off at the selected
temperature to prevent coil freezing.
17
®
IAQ TOTAL HOME COMFORT SYSTEM
Notes
68-0287—04