Honeywell VISIONPRO 68-0287-04 User Manual page 15

ISU
Parameter Installer Setup
Number Name
340 Indoor Temp
Sensor
342 Outdoor Temp
Sensor
345 Dual Fuel Heat
Pump Control
346 Dual Fuel Heat
Pump Upstage to
Furnace Timer (in
hours)
347 Droop
Temperature
350 Heat Pump
Balance Point
(also compressor
lockout)
Temperature
360 Heat Pump
Auxiliary Heat
Lockout
Temperature
365 Discharge Temp
Sensor
366 Zoning High
Temperature
Limit
367 Zoning Low
Temperature
Limit
Table 3. Installer Setup Menu. (Continued)
Settings
(Factory Defaults Shown in Bold)
0 Thermostat location only
1 Remote indoor sensor(s) location(s) only
2 Average between thermostat and sensor
locations
E Auto Discover
0 None
1 Yes
1 Droop Control
0 No Droop Control
2 Droop Control with Auxiliary heat lockout
1 1 hr.
0 Disabled
0.5 0.5 hrs.
1.5 1.5 hrs.
2 2 hrs.
3 3 hrs.
4 hrs.
4
5 5 hrs.
6 6 hrs.
8 8 hrs.
10 10 hrs.
12 12 hrs.
14 14 hrs.
16 16 hrs.
2
2°F 1.0°C
3
3°F 1.5°C
4
4°F 2.0°C
5
5°F 2.5°C
40 4.5 40°F 4.5°C
0 No heat pump compressor lockout
5 -15 5°F -15.0°C
10 -12 10°F -12.0°C
15 -9.5 15°F -9.5°C
20 -6.5 20°F -6.5°C
25 -4 25°F -4.0°C
30 -1 30°F -1.0°C
35 1.5 35°F 1.5°C
45 7 45°F 7.0°C
50 10 50°F 10.0°C
55 13 55°F 13.0°C
60 15.5 60°F 15.5°C
(Show 1/2 degree C)
0 No heat pump auxiliary lockout
5 -15 5°F -15.0°C
10 -12 10°F -12.0°C
15 -9.5 15°F -9.5°C
20 -6.5 20°F -6.5°C
25 -4 25°F -4.0°C
30 -1 30°F -1.0°C
35 1.5 35°F 1.5°C
40 4.5 40°F 4.5°C
45 7 45°F 7.0°C
50 10 50°F 10.0°C
55 13 55°F 13.0°C
60 15.5 60°F 15.5°C
65 18.5 65°F 18.5°C
(Show 1/2 degree C)
E Auto Discover
0 None
1 Remote
160 160°F (71°C)
0 Disabled
110–170 110°F to 170°F (43.5°C to 76.5°C)
40 160°F (71°C)
0 Disabled
35-50 35°F to 50°F (1.5°C to 10°C)
VISIONPRO
Indoor temperature sensors will display the
temperature at the sensor location or an average of
two indoor temperature sensors, not including the
temperature sensor in the thermostat. The
temperature sensor in the thermostat is disabled
when using remote indoor temperature sensor(s).
An outdoor temperature sensor is required for heat
pump compressor lockout (ISU350), heat pump
auxiliary lockout (ISU360), dual fuel heat pump
balance point (ISU360) and Humidification with
Frost Protection (ISU372).
See Dual Fuel Heat Pump control on page 23.
See Dual Fuel Heat Pump control on page 23.
The fossil fuel will turn on when the outdoor
temperature is above the balance point if the room
temperature droops below the selected droop
temperature setting, and the compressor will be
disabled.
Only shown for heat pump applications with an
outdoor temperature sensor present.
If electric backup is selected then the default is No
Compressor lockout.
Only shown for heat pump applications with an
outdoor temperature sensor present.
Only Shown if ISU110 = 1 (Master Zone Controller)
and Discharge Temperature Sensor is available.
Only Shown if ISU110 = 1 (Master Zone Controller)
and Discharge Temperature Sensor is available.
15
®
IAQ TOTAL HOME COMFORT SYSTEM
Notes
68-0287—04