Aiwa CX-JN10 Service Manual
  1. Manuals
  2. Brands
  3. Aiwa Manuals
  4. Stereo System
  5. CX-JN10
  6. Service manual
Aiwa CX-JN10 Service Manual

Aiwa CX-JN10 Service Manual

Compact disc deck receiver
Hide thumbs
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Ver 1.0 2004.03
CX-JN10 is the tuner, amplifier, cassette deck
and CD player section in JAX-N10/PK10.
TUNER
FM tuning range
87.5 MHz to 108 MHz
FM
usable sensitivity (IHF)
AEP, UK models:
16.8 dBf
Except AEP, UK models:
13.2 dBf
FM antenna terminal
75 ohms (unbalanced)
AM
tuning range
AEP, UK, E, EA, TW models:
531 kHz to 1602 kHz
E51 model:
530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1710 kHz (9 kHz step)
SP, AUS models:
531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)
AM usable sensitivity
350 V/m
AM antenna
Loop antenna
AMPLIFIER
Power
output
Rated: 12 W + 12 W (6 ohms, T.H.D.
AEP, UK models:
1 %, 1 kHz/DIN 45500)
Reference: 15 W + 15 W (6 ohms,
T.H.D. 10 %, 1 kHz/DIN 45324)
MUSIC POWER: 27 W +27 W
Except AEP, UK models:
Rated: 36 W + 36 W (1 kHz, T.H.D. 1
%, 6 ohms)
Reference: 45 W + 45 W (1 kHz,
T.H.D. 10 %, 6 ohms)
Total harmonic distortion
0.08 % (6 W, 1 kHz, 6 ohms, DIN
AUDIO)
Input
VIDEO/AUX: 400 mV
MIC: 1.7 mV (10k ohms)
(Except AEP, UK models)
Outputs
SPEAKER:
6 ohms or more
PHONES: 32 ohms or more
Sony Corporation
9-877-593-01
2004C05-1
Home Audio Company
© 2004.03
Published by Sony Engineering Corporation
Model Name Using Similar Mechanism
CD Mechanism Type
CD
Base Unit Name
Section
Optical Pick-up Block Name
Optical Pick-up Name
Model Name Using Similar Mechanism
Tape deck
Section
Tape Transport Mechanism type

SPECIFICATIONS

CASSETTE DECK
Track format
4 tracks, 2 channels stereo
Frequency response
50 Hz – 8 kHz
Recording system
AC bias
Heads
Deck A: playback x 1
Deck B: recording/playback x 1,
erase x 1
CD PLAYER
Laser
Semiconductor laser
( = 780 nm)
Emission duration:
continuous
D/A converter
1 bit dual
Signal-to-noise ratio
85 dB (1 kHz, 0 dB)
Harmonic distortion
0.05 % (1 kHz, 0 dB)
GENERAL
Power
requirements
AEP, UK models:
230 V AC, 50/60 Hz
110
- 120V / 220 - 240V AC
E, E51, SP models:
(Switchable), 50 Hz/60 Hz
EA model:
120 - 127V / 220 V AC
(Switchable), 50 Hz/60 Hz
TW model:
120 V AC, 50 Hz/60 Hz
AUS model:
240 V AC, 50 Hz/60 Hz
COMPACT DISC DECK RECEIVER
CX-JN10
AEP Model
UK Model
Australian Model
CX-JN1
CDM74S-K6BD72
BU-K6BD72
KSM-213DCP
KSS-213D
CX-JN1
CWM43FF13
Power consumption
AEP, UK models:
40 W
Except AEP, UK models:
74 W
Power consumption
With ECO mode on: 0.25 W
in standby mode
With ECO mode off: 15 W
Dimensions (W x H x D)
280 x 330 x 392.5 mm
Weight
AEP, UK models:
6.1 kg
E51 model:
6.7 kg
E, EA, SP, TW, AUS models: 6.8 kg
Specifications and external appearance are subject to change
without notice.
COPYRIGHT
Check copyright laws relevant to recordings from discs, tuner
or tape for the country where the unit is to be used.
Abbreviation
AUS : Australian model
E51 : Chilean and Peruvian models
EA : Saudi Arabia model
SP
: Singapore model
TW : Taiwan model
E Model

Advertisement

Table of Contents
loading

Related Manuals for Aiwa CX-JN10

Summary of Contents for Aiwa CX-JN10

  • Page 1: Specifications

    CX-JN10 SERVICE MANUAL AEP Model UK Model Ver 1.0 2004.03 E Model Australian Model CX-JN10 is the tuner, amplifier, cassette deck and CD player section in JAX-N10/PK10. Model Name Using Similar Mechanism CX-JN1 CD Mechanism Type CDM74S-K6BD72 Base Unit Name...
  • Page 2 LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.

  • Page 3: Table Of Contents

    CX-JN10 TABLE OF CONTENTS SERVICING NOTES EXPLODED VIEWS ..........4 7-1. Case Section ..............47 GENERAL 7-2. Tape Deck Section ............48 7-3. Panel Board Section ............49 Location of Controls ............7 7-4. Key Section ..............50 7-5. Front Cabinet Section ............. 51 DISASSEMBLY 7-6.

  • Page 4: Servicing Notes

    CX-JN10 SECTION 1 SERVICING NOTES • MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP – Back Panel – BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc.
  • Page 5 CX-JN10 HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF. 1 Remove the case (side-L). 2 Turn the loading gear in the direction of arrow A . 3 Pull-out the disc tray.
  • Page 6 CX-JN10 SERVICE POSITION – CD mechanism deck – main board (CN691) Connect wire (flat type) (19 core) to main board (CN691) and BD board (CN710). BD board (CN710) – Tape mechanism deck – panel board (CN601) main board (CN302) main board (CN301) Connect wire (flat type) (13 core) to panel board (CN601) and mechanical deck.

  • Page 7: General

    CX-JN10 SECTION 2 GENERAL This section is extracted from instruction manual. • LOCATION OF CONTROLS Main unit: front 5 MULTI JOG ! Remote sensor When used in combination with ENTER and MULTI Receives a signal from the remote. Refer to the pages indicated in parentheses for details.

  • Page 8: Remote Control

    CX-JN10 Remote control TAPE A/B DISC SKIP Select a disc. Refer to the pages indicated in parentheses for details. TUNER MODE Switches between stereo or monaural FM reception. When the unit is turned off: activates or deactivates r, t DEMO.

  • Page 9: Disassembly

    CX-JN10 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.

  • Page 10: Case (Side-L/R)

    CX-JN10 Note: Follow the disassembly procedure in the numerical order given. 3-2. CASE (SIDE-L/R) 2 two screws 5 case (side-L) × (BVTP3 1 two case screws 2 two screws × (BVTP3 1 two case screws 1 case screw 5 case (side-R) 1 case screw 3-3.

  • Page 11: Tray Panel

    CX-JN10 3-4. TRAY PANEL 1 Turn the loading gear in the direction of arrow A . 2 Pull-out the disc table. 3 four claws 4 tray panel 3-5. CD MECHANISM DECK (CDM74S-K6BD72) 5 CD mechanism deck (CDM74S-K6BD72) 1 wire (flat type) (19 core)

  • Page 12: Front Panel Section

    CX-JN10 3-6. FRONT PANEL SECTION 1 screw × (BVTP3 3 screw 2 terminal (BVWHTP) 4 HP board 8 connector (CN101) 5 wire (flat type) (11 core) (CN694) 6 connector (CN302) 6 connector (CN301) 9 front panel section 7 three screws ×...

  • Page 13: Rear Cabinet Section

    CX-JN10 3-8. REAR CABINET SECTION 3 rear cabinet section 1 wire (flat type) (11 core: EXCEPT AEP, UK) (CN801) (15 core: AEP, UK) (CN802) 2 three screws × (BVTP3 2 screw × (BVTP3 3-9. PT BOARD, MAIN BOARD • Abbreviation...

  • Page 14: Table Assy

    CX-JN10 3-10. TABLE ASSY 5 two claws 4 hook 3 wire (flat type) (5 core) (CN702) 1 Turn the loading gear 2 Pull-out the table assy. in the direction of arrow A . 6 table assy 3-11. MOTOR (TB) BOARD 1 screw (PTPWH M2.6)

  • Page 15: Motor (Ld) Board

    CX-JN10 3-12. MOTOR (LD) BOARD 3 two screws (BTTP M2.6) 4 MOTOR (LD) board 2 connector (CN704) 1 belt (loading) 3-13. BASE UNIT (BU-K6BD72) 9 base unit (BU-K6BD72) 7 three insulators 8 insulator 3 three coil springs (insulator) 5 coil spring...

  • Page 16: Motor Gear Assy (Sled) (M701), Bd Board

    CX-JN10 3-14. MOTOR GEAR ASSY (SLED) (M701), BD BOARD 7 gear (A) 6 claw 8 gear (B) 2 two screws (P2 × 3) 5 wire (flat type) (16 core) (CN708) qa BD board 0 motor gear assy (SLED) (M701) 1 Remove two solders.

  • Page 17: Test Mode

    CX-JN10 SECTION 4 TEST MODE MC COLD RESET CHANGE-OVER OF AM TUNER STEP BETWEEN • The cold reset clears all data including preset data stored in the 9 kHz AND 10 kHz (Except AEP and UK models) • A step of AM channels can be changed over between 9 kHz and RAM to initial conditions.
  • Page 18 CX-JN10 CD TEST MODE • This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pickup. Procedure: 1. In the status where AC plug is disconnected, while pressing [CD] button, connect the AC plug to turn the power on.

  • Page 19: Electrical Adjustments

    CX-JN10 SECTION 5 ELECTRICAL ADJUSTMENTS Note: Clear RF signal waveform means that the shape “ ◊ ” can be clearly CD SECTION distinguished at the center of the waveform. Note: RF signal waveform 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given.

  • Page 20: Diagrams

    CX-JN10 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – CD Section – OPTICAL PICK-UP BLOCK CD DSP (KSM-213DCP) IC721 FIN2 LCHO (Page 22) DETECTOR EFMIN ERROR RF AMP CONVERTER RCHO CORRECT R-CH FIN1 • R-ch is omitted due to same as L-ch.

  • Page 21: Block Diagram - Tuner/Tape/Panel Section

    CX-JN10 6-2. BLOCK DIAGRAM – TUNER/TAPE/PANEL Section – PB SWITCH (Page 22) L-CH Q301 (PB) (DECK-A) R-CH R-CH TUNER PACK FM 75Ω L-CH (Page 22) FM ANT (COAXIAL) PB SWITCH R-CH R-CH Q303 L-CH AM LOOP AM ANT MUTING Q305...

  • Page 22: Block Diagram - Amp/Power Supply Section

    CX-JN10 6-3. BLOCK DIAGRAM – AMP/POWER SUPPLY Section – (EXCEPT AEP, UK) MIC LEVEL (EXCEPT AEP, UK) SWITCHING Q401 Q231 VR401 OUTPUT LEVEL J401 MIC MIXING DETECT R-CH R-CH Q233, 234 MIC AMP MIC AMP IC401 (1/2) IC401 (2/2) SWITCHING –VH...

  • Page 23: Note For Printed Wiring Boards And Schematic Diagrams

    CX-JN10 • Circuit Boards Location 6-4. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board: Note on Schematic Diagram: SENSOR board • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. pF: µµF •...

  • Page 24: Printed Wiring Board - Bd Section

    CX-JN10 PRINTED WIRING BOARD – BD Section – • 6-5. See page 23 for Circuit Boards Location. :Uses unleaded solder. M702 (SPINDLE) BD BOARD S701 (LIMIT IN) − IC722 OPTICAL M701 PICK-UP (SLED) BLOCK (KSM-213DCP) − CN710 (VC) TP (FE)

  • Page 25: Schematic Diagram - Bd Section

    CX-JN10 SCHEMATIC DIAGRAM – BD Section – • • 6-6. See page 42 for IC Block Diagram. See page 42 for Waveforms. R732 R731 2.2k R721 R722 C752 C753 R707 C709 C746 C742 C708 R729 C744 C754 C745 C750 C751...

  • Page 26: Printed Wiring Boards - Changer Section

    CX-JN10 PRINTED WIRING BOARDS – CHANGER Section – • 6-7. See page 23 for Circuit Boards Location. :Uses unleaded solder. SENSOR BOARD SW BOARD CN751 IC731 S751 MAIN BOARD OPEN/CLOSE CN692 DETECT (Page 32) DRIVER BOARD CLOSE C715 OPEN Q731...

  • Page 27: Schematic Diagram - Changer Section

    CX-JN10 SCHEMATIC DIAGRAM – CHANGER Section – • 6-8. See page 42 for IC Block Diagrams. LOADING MOTOR DRIVE IC701 BA6956AN R702 R701 CN721 CN704 LM-2 LM-2 D701 M751 C751 LM-1 LM-1 MTZJ-T-77 0.01 (LOADING) 5.1A S711 DISC TRAY ADDRESS DETECT...

  • Page 28: Schematic Diagram - Main Section (1/4)

    CX-JN10 6-9. SCHEMATIC DIAGRAM – MAIN Section (1/4) – (1/4) R017 (EXCEPT AEP,UK) 0.22 (AEP,UK) D019 0.33 (EXCEPT AEP,UK) EGP20D VM(AC) (AUS) VM(AC) C007 D020 VH(AC) 3300 25V (AEP,UK) D021 D022 EGP20D EGP20D EGP20D 3300 35V (EXCEPT AEP,UK) VH(AC) C011 C012 C033...

  • Page 29: Schematic Diagram - Main Section (2/4)

    CX-JN10 6-10. SCHEMATIC DIAGRAM – MAIN Section (2/4) – D107 (2/4) R123 Q101,103 R131 MC2838 6.8k 4.7k PRE DRIVE C133 C127 R119 2.2k 100p 100V Q123 ∗ ∗ R117 R121 Q123,124 C105 FINAL DRIVE C181 2.2k R133 D105 (AEP,UK) ∗...

  • Page 30: Schematic Diagram - Main Section (3/4)

    CX-JN10 6-11. SCHEMATIC DIAGRAM – MAIN Section (3/4) – • • See page 42 for IC Block Diagram. See page 42 for Waveforms. (3/4) SP-A-GND C687 0.01 TU/AUX-A-GND CD-A-GND FR-A-GND FUNC-A-GND CD-D-GND CD-P-GND FR-D-GND CD-VM CD-VM TP601 (AEP,UK) JR601 JR611...

  • Page 31: Schematic Diagram - Main Section (4/4)

    CX-JN10 6-12. SCHEMATIC DIAGRAM – MAIN Section (4/4) – • See page 42 for IC Block Diagram. (EXCEPT AEP,UK) (4/4) CN801 (AEP,UK) RDS-DATA C912 C911 DATA FM 75Ω 100p 100p (COAXIAL) PLL-CE TUNER PACK SUPPLIED WITH TUNED THE ASSEMBLED TUNED...

  • Page 32: Printed Wiring Board - Main Section

    CX-JN10 6-13. PRINTED WIRING BOARD – MAIN Section – • :Uses unleaded solder. See page 23 for Circuit Boards Location. MAIN BOARD (AEP, UK) R809 R812 R810 JW802 BOARD JW661 JW803 CN710 R807 JW662 (Page 24) JW611 JW618 JW805 JW804...

  • Page 33: Printed Wiring Board - Hp Section

    CX-JN10 6-14. PRINTED WIRING BOARD – HP Section – • 6-15. SCHEMATIC DIAGRAM – HP Section – See page 23 for Circuit Boards Location. :Uses unleaded solder. MAIN BOARD WH201 (Page 32) FB221 WH230 WH230 JW222 J221 PHONES JW224 R-OUT...

  • Page 34: Printed Wiring Board - Panel Section

    CX-JN10 6-16. PRINTED WIRING BOARD – PANEL Section – • :Uses unleaded solder. See page 23 for Circuit Boards Location. R906 C909 R908 R927 C908 D623 D622 C907 R932 R905 IC801 C905 D620 D621 (Page 32) C917 FL902 MAIN BOARD...

  • Page 35: Schematic Diagram - Panel Section

    CX-JN10 6-17. SCHEMATIC DIAGRAM – PANEL Section – • • • See page 42 for IC Block Diagrams. See page 42 for Waveforms. See page 45 for IC Pin Function Description. FL902 FLUORESCENT INDICATOR TUBE JW902 R943 R942 C914 C915 1.8k...

  • Page 36: Printed Wiring Boards - Key Section

    CX-JN10 6-18. PRINTED WIRING BOARDS – KEY Section – • See page 23 for Circuit Boards Location. :Uses unleaded solder. KEY BOARD LED901 STANDBY/ON S315 POWER S801 S307 VOLUME MODE S301 − 315, S317 − 323 R312 S308 ENTER CN301...

  • Page 37: Schematic Diagram - Key Section

    CX-JN10 6-19. SCHEMATIC DIAGRAM – KEY Section – R801 R803 R809 R811 S801 S803 VOLUME TREBLE R802 C801 C802 R804 R810 C805 C806 R812 1000p 1000p 1000p 1000p R301 R302 R303 R304 R305 R306 1.2k 1.2k S306 S301 S302 S303...

  • Page 38: Printed Wiring Board - Pt Section - (Aep, Uk, Aus)

    CX-JN10 6-20. PRINTED WIRING BOARD – PT Section – (AEP, UK, AUS) • :Uses unleaded solder. See page 23 for Circuit Boards Location. PT BOARD JW204 CN091 JW214 (AC IN) MAIN PR093 PT002 BOARD POWER TRANSFORMER WH011 (MAIN) (Page 32) RY001 ∗...

  • Page 39: Schematic Diagram - Pt Section

    CX-JN10 6-21. SCHEMATIC DIAGRAM – PT Section – (AEP, UK, AUS) (AEP,UK) WH091 VL(AC) VL(AC) GND(M) FIL-1 FIL-2 (Page 28) P-ON VSTBY PT002 POWER TRANSFORMER WH093 (MAIN) VM(AC) VM(AC) ∗ VH(AC) NOT REPLACEABLE: BUILT IN TRANSFORMER VH(AC) VL(AC) ∗ VL(AC)

  • Page 40: Printed Wiring Board - Pt Section

    CX-JN10 6-22. PRINTED WIRING BOARD – PT Section – (E, EA, E51, SP, TW) • See page 23 for Circuit Boards Location. :Uses unleaded solder. PT BOARD (AC IN) PT002 POWER TRANSFORMER (SUB) CN090 JW017 D002 D003 PT004 POWER TRANSFORMER...

  • Page 41: Schematic Diagram - Pt Section

    CX-JN10 6-23. SCHEMATIC DIAGRAM – PT Section – (E, EA, E51, SP, TW) PT004 POWER TRANSFORMER CN093 (MAIN) VM(AC) VM(AC) VH(AC) VH(AC) (E,EA,E51,SP) VL(AC) VL(AC) JW032 S001 GND(M) (TW) VOLTAGE SELECTOR FIL-1 100-120V ∗ (Page 28) FIL-2 220-240V P-ON C003 VSTBY 0.01...
  • Page 42 CX-JN10 • Waveforms • IC Block Diagrams – BD Board – – MAIN Board – – PANEL Board – – BD Board – 1 IC721 4 (RF) (CD Play Mode) qa L311 6, 7 (REC Mode) qf IC901 qd (XT2)
  • Page 43 CX-JN10 – DRIVER Board – IC701, 712 BA6956AN CONTROL LOGIC – MAIN Board – IC601 BD3881FV BASS BASS VOLUME TREBLE LOGIC CONTROL VOLUME TREBLE IC672 BU2092F-E2 16 15 14 13 12 11 12 BIT CONTROL SHIFT CIRCUIT REGISTER OUTPUT 12 BIT...

  • Page 44: Panel Board

    CX-JN10 – PANEL Board – IC201 BU2099FV 17 16 15 14 13 12 12 BIT CONTROL SHIFT CIRCUIT REGISTER OUTPUT 12 BIT BUFFER STORAGE (OPEN DRAIN) REGISTER 6 7 8 9 10 IC501 MM1614A CURRENT BIAS LIMITTER REFERENCE − DRIVER...
  • Page 45 CX-JN10 • IC Pin Function Description PANEL BOARD IC901 LC87696B-52D8 (SYSTEM CONTROLLER) LC876772B-52N2-E (AEP and UK models), LC876756C-52N7-E (EXCEPT AEP and UK models) Pin No. Pin Name Description SYS-MUTE Line muting on/off control signal output terminal RDS DO RDS serial data input from the tuner pack (AEP and UK models)
  • Page 46 CX-JN10 Pin No. Pin Name Description Recording (forward direction) detection signal input and segment drive signal output to the REC FWD/S11 fluorescent indicator tube Deck-A cassette detection signal input and segment drive signal output to the fluorescent A HALF/S12 indicator tube...

  • Page 47: Exploded Views

    CX-JN10 SECTION 7 EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they • -XX and -X mean standardized parts, so they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.

  • Page 48: Tape Deck Section

    CX-JN10 7-2. TAPE DECK SECTION not supplied (EXCEPT AEP, UK) not supplied panel board section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-245-177-11 ROTARY (JOG), KNOB 1-796-485-51 DECK, MECHANICAL (CWM43FF13) 4-245-179-11 ROTARY (TRE), KNOB 4-245-289-11 KNOB (MIC), ROTARY (EXCEPT AEP, UK)

  • Page 49: Panel Board Section

    CX-JN10 7-3. PANEL BOARD SECTION not supplied (EXCEPT AEP, UK) (EXCEPT AEP, UK) not supplied key section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-861-661-11 CD KEY BOARD 1-751-688-11 WIRE (FLAT TYPE) (13 CORE) 1-688-400-15 HP BOARD...

  • Page 50: Key Section

    CX-JN10 7-4. KEY SECTION front cabinet section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-245-193-01 RING (BASS) 4-245-172-21 KEY (FUN) (TAPE A/B. TUNER BAND. 4-254-978-01 WINDOW, DISPLAY (AEP, UK) VIDEO/AUX. CD. N. x) 4-254-978-11 WINDOW, DISPLAY (E, EA, SP, TW, AUS)

  • Page 51: Front Cabinet Section

    CX-JN10 7-5. FRONT CABINET SECTION Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-245-198-01 WINDOW (2), CASSETTE 4-254-979-11 CABINET, FRONT (EXCEPT AEP, UK) 4-245-160-21 BOX (2), CASSETTE 4-231-836-01 SPRING (HEART CAM-A) 4-245-196-01 SPRING (BOX CASS R), TORSION...

  • Page 52: Chassis Section

    CX-JN10 7-6. CHASSIS SECTION (E, EA, E51, SP, TW) not supplied not supplied PT004 (AEP, UK, AUS) not supplied not supplied not supplied supplied not supplied not supplied PT002 (AEP, UK) C911 not supplied C912 C913 not supplied C950 not supplied...

  • Page 53: Cd Mechanism Deck Section-1

    CX-JN10 7-7. CD MECHANISM DECK SECTION-1 (CDM74S-K6BD72) M741 CD mechanism deck section -2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-243-815-01 TABLE (LOADING) 1-687-134-12 MOTOR (TB) BOARD 4-218-252-61 SCREW (+PTPWH M2.6), FLOATING 4-243-816-01 TRAY 4-218-253-21 SCREW (M2.6), +BTTP...

  • Page 54: (Cdm74S-K6Bd72)

    CX-JN10 7-8. CD MECHANISM DECK SECTION-2 (CDM74S-K6BD72) S711 M751 CD mechanism deck section -3 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-218-252-61 SCREW (+PTPWH M2.6), FLOATING 3-016-533-11 WASHER (FR), STOPPER 4-244-108-01 GEAR, SWING 4-244-034-01 BELT (LOADING)

  • Page 55: (Cdm74S-K6Bd72)

    CX-JN10 7-9. CD MECHANISM DECK SECTION-3 (CDM74S-K6BD72) BU-K6BD72 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4955-707-2 PULLEY (A5) ASSY, CHUCKING 4-227-549-11 INSULATOR 4-227-045-31 SPRING (INSULATOR), COIL 1-471-035-11 MAGNET ASSY 4-231-189-01 PULLEY (B), CHUCKING 4-231-151-01 STOPPER (BU) 4-218-252-61 SCREW (+PTPWH M2.6), FLOATING...

  • Page 56: Base Unit Section (Bu-K6Bd72)

    CX-JN10 7-10. BASE UNIT SECTION (BU-K6BD72) not supplied (M702) not supplied (M701) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref.

  • Page 57: Electrical Parts List

    CX-JN10 SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
  • Page 58 CX-JN10 CD KEY DRIVER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R726 1-216-819-11 METAL CHIP 1/10W C741 1-162-306-11 CERAMIC 0.01uF R727 1-216-809-11 METAL CHIP 1/10W C751 1-162-306-11 CERAMIC 0.01uF R728 1-216-841-11 METAL CHIP 1/10W C752 1-164-159-21 CERAMIC 0.1uF...
  • Page 59 CX-JN10 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R226 1-260-089-11 CARBON 1/2W < FERRITE BEAD > (EXCEPT AEP, UK) R226 1-260-090-61 CARBON 1/2W FB401 1-410-396-41 FERRITE 0.45uH (EXCEPT AEP, UK) (AEP, UK) < IC >...
  • Page 60 CX-JN10 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R408 1-216-174-00 RES-CHIP 1/8W < VARIABLE RESISTOR > (EXCEPT AEP, UK) R409 1-216-825-11 METAL CHIP 2.2K 1/10W VR401 1-227-502-11 RES, VAR, CARBON 10K (MIC MIXING) (EXCEPT AEP, UK)
  • Page 61 CX-JN10 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C042 1-126-948-11 ELECT 100uF C129 1-100-152-11 CERAMIC CHIP 100PF 100V (AEP, UK) (AEP, UK) C042 1-126-964-11 ELECT 10uF C130 1-100-152-11 CERAMIC CHIP 100PF 100V (EXCEPT AEP, UK)
  • Page 62 CX-JN10 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C605 1-130-481-00 MYLAR 0.0068uF 5% CN601 1-793-766-11 CONNECTOR, BOARD TO BOARD 30P C606 1-130-481-00 MYLAR 0.0068uF 5% CN691 1-784-780-11 CONNECTOR, FFC 19P C607 1-162-962-11 CERAMIC CHIP...
  • Page 63 CX-JN10 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D662 8-719-083-60 DIODE UDZSTE-174.7B JR651 1-216-296-11 SHORT CHIP D663 8-719-988-61 DIODE 1SS355TE-17 JR701 1-216-864-11 SHORT CHIP D671 8-719-988-61 DIODE 1SS355TE-17 JR801 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP, UK)
  • Page 64 CX-JN10 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q182 8-729-052-79 TRANSISTOR 2SD1306NETL (EXCEPT AEP, UK) R012 1-216-228-00 RES-CHIP 1/8W Q183 8-729-600-22 TRANSISTOR 2SA1235-F (EXCEPT AEP, UK) Q231 6-550-293-01 FET 2SK2937 (EXCEPT AEP, UK) R013...
  • Page 65 CX-JN10 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R124 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R074 1-216-838-11 METAL CHIP 1/10W R125 1-216-823-11 METAL CHIP 1.5K 1/10W (EXCEPT AEP, UK) R126 1-216-823-11 METAL CHIP 1.5K...
  • Page 66 CX-JN10 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R156 1-216-823-11 METAL CHIP 1.5K 1/10W R253 1-216-833-11 METAL CHIP 1/10W (EXCEPT AEP, UK) (EXCEPT AEP, UK) R157 1-216-809-11 METAL CHIP 1/10W R158 1-216-809-11 METAL CHIP...
  • Page 67 CX-JN10 MAIN MOTOR (LD) MOTOR (TB) PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R699 1-216-821-11 METAL CHIP 1/10W R610 1-216-836-11 METAL CHIP 1/10W R700 1-216-837-11 METAL CHIP 1/10W R612 1-216-829-11 METAL CHIP 4.7K 1/10W...
  • Page 68 CX-JN10 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C413 1-126-960-11 ELECT D508 8-719-991-33 DIODE 1SS133T-77 (EXCEPT AEP, UK) D509 8-719-991-33 DIODE 1SS133T-77 C414 1-164-156-11 CERAMIC CHIP 0.1uF D601 8-719-991-33 DIODE 1SS133T-77 (EXCEPT AEP, UK)
  • Page 69 CX-JN10 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R419 1-216-821-11 METAL CHIP 1/10W < TRANSISTOR > (EXCEPT AEP, UK) R501 1-249-408-11 CARBON 1/4W Q601 8-729-116-57 TRANSISTOR 2SB1068-K R502 1-216-841-11 METAL CHIP 1/10W Q602 8-729-140-04 TRANSISTOR...
  • Page 70 CX-JN10 PANEL SENSOR Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R917 1-216-845-11 METAL CHIP 100K 1/10W R973 1-216-845-11 METAL CHIP 100K 1/10W (EXCEPT AEP, UK) R918 1-216-845-11 METAL CHIP 100K 1/10W R974 1-247-879-11 CARBON 100K...
  • Page 71 CX-JN10 SENSOR Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > ACCESSORIES ************ IC731 (NOT SUPPLIED) 1-569-007-12 ADAPTOR, CONVERSION 2P (E) ************************************************************ 1-569-008-32 ADAPTOR, CONVERSION (E51, EA, SP) 1-687-669-12 SW BOARD 1-770-019-51 ADAPTOR, CONVERSION PLUG (UK) ********* <...

  • Page 72: Revision History

    CX-JN10 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...

Table of Contents