Initialization Of B, C, D, E, F Page Data; Initialization Of C Page Data; Modification Of C Page Data - Sony DCR-PC2E Service Manual

1-2.

INITIALIZATION OF B, C, D, E, F PAGE DATA

1-2-1.

INITIALIZATION OF C PAGE DATA

1. Initializing the C Page Data
Note: If the C page data has been initialized, the following adjustments
need to be performed again.

1) Modification of C page data

2) Servo and RF system adjustments
3) Video system adjustments
Adjusting page C
Adjusting Address 10 to DF
Initializing Method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 80, set data: 0C, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 3, address: 80, and check that the data changes to
"1C".
4) Perform "Modification of C Page Data".
2. Modification of C Page Data
If the C page data has been initialized, change the data of the "Fixed
data-2" address shown in the following table by manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note : If copy the data built in the different model, the camcorder
may not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of C Page data
1) Select page: 2, address: 00, and set data: 29.
2) Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
3. C Page Table
Note: Fixed data-1 : Initialized data. (Refer to "1. Initializing the C Page
Data".)
Fixed data-2 : Modified data. (Refer to "2. Modification of C Page
Data".)
Initial value
Address
NTSC PAL
00 to 0F
10 EE EE
11 00 00
12 EE EE
13 00 00
14
15
16 E0 E0
17 E0 E0
18 2A 2A
19 2A 2A
1A
1B 33 33
1C 33 33
1D
1E 25 25
1F 3E 3E
20 3E 3E
21 DC DC
22 99 99
23
24
25 88 88
26 E3 E3
27 A1 A1
28
29
2A
2B 04 04
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38 00 00
39 00 00
3A 00 00
3B 00 00
3C 00 00
3D 00 00
3E 00 00
3F 00 00
40 00 00
5-8
Remark
Switching position adj.
Fixed data-1
(Initialized data)
Cap FG duty adj.
Treel FG duty adj.
AEQ adj.
Fixed data-1
AEQ adj.
Fixed data-1
AGC center level adj.
PLL f adj.
0
APC adj.
LPF f adj.
0
Fixed data-1
(Initialized data)
S VIDEO out Y level adj.
S VIDEO out Cr level adj.
S VIDEO out Cb level adj.
Fixed data-1
(Initialized data)
Chroma BPF f adj.
0
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data, copy the data built in
the same model.)
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
(Initialized data)
Emergency memory address