UPM HTM511A Owner's Manual

Line-Voltage Thermostat
HTM511A
OWNER'S
MANUAL
Congratulations on your
purchase of this UPM line-
voltage thermostat. Please
take the time to read and
understand this manual so
you can begin to enjoy the
convenience this product
offers.
FEATURES
Ideal for electric baseboards,
convectors and radiant
floor/ceiling heaters
Precision temperature control
with selectable cycle rates
Intelligent Adaptive Regulation
Temperature display in °C or °F
Quiet operation
Simple two wire installation
Rating: 120V~240V AC, 60Hz
MAXIMUM LOAD: 12.5A
- 3000W @ 240V or
- 1500W @ 120V
MINIMUM LOAD: 500W
PAGE 1
OPERATING MODE SETTING
This thermostat gives you the options to:
Select the cycle rate; and/or
Select the temperature display in °C or °F
To enter the setting mode, press both the UP and DOWN buttons together.
In the setting mode:
Press the UP button to select the desired CYCLE RATE.
There are 3 different cycle rates to choose from.
Cr CYCLE RATES
Cr-0 OFF (fixed span)
Cr-1 12 seconds
240 seconds (4 minutes)
Cr-2
NOTE: When using this thermostat with heaters or heating appliances with a fan,
we do NOT recommend setting the cycle rate to Cr-1 (12 seconds).
Press the DOWN button to toggle between the °C or °F display.
NOTE: The default temperature unit is °C
PAGE 6
CAUTION!
TO AVOID FIRE, SHOCK, OR DEATH, SHUT OFF POWER SUPPLY
*
AT THE CIRCUIT BREAKER OR FUSE AND TEST THAT THE
POWER IS OFF BEFORE WIRING.
This product operates at 120V to 240V AC. Do not install it unless
you are completely familiar and competent with house wiring.
Handle with caution to prevent any risk of electrical shock that
could cause serious injury or death.
Do NOT connect voltage different from device rating.
All wiring must comply with applicable codes and regulations.
For wiring, use COPPER conductors only.
Ensure that the heating system is protected by appropriate circuit
breakers or fuses.
PAGE 2
OPERATION
CURRENT TEMPERATURE DISPLAY
The current (room) temperature is F
normally displayed on the LCD screen.
TEMPERATURE SETTING
Press the UP or DOWN button once to enter the temperature setting
1
mode. The "hand" symbol will appear, and the display will now show
the current set temperature.
2
Press the UP or DOWN button to adjust to the desired set temperature.
The temperature can be set in increments of 0.5°C.
The temperature setting range is from 5°C to 35°C.
NOTE: Press and hold the button
down to accelerate the setting. If no
F
button is pressed within 8 seconds,
the display will automatically return
to the current temperature display.
PAGE 7
INSTALLATION
This thermostat is compatible with most high voltage (120V to 240V AC)
electrical heaters or heating appliances. The minimum load
requirement is 500W.
The thermostat must be fully installed in order for the buttons and LCD to operate.
CHOOSING A LOCATION FOR A NEW THERMOSTAT
This thermostat should be mounted:
Approximately 5ft (1.5m) from the floor.
Near or in a frequently occupied room, preferably on an inside partitioning wall.
On a section of the wall without pipes or duct-work.
This thermostat should NOT be mounted:
Near a window, on an outside wall, or next to a door leading outside.
Exposed to direct light or heat from the sun, lamp, fireplace, or other heat radiating
objects which may cause false readings.
Near or in a direct airflow from supply registers and return-air grilles.
Near concealed pipes and chimneys.
In areas of poor air circulation, such as behind a door or in an alcove.
PAGE 3
OPERATION
HEAT "ON" INDICATOR / OUTPUT POWER LEVEL
When the thermostat activates the heating system, the symbol will
appear. Equipped with an intelligent proportional regulation, this thermostat will
determine the amount of power needed by the electric heater to maintain the
room temperature to precisely that of the set temperature. The "Power Bar" will
indicate the current output power level. 1 BAR = 20% and 5 BARS = 100%
F
Indicates that the HEAT "ON"
Indicactor
thermostat is operating
at 40% in power
DISPLAY AUTO-RETURN
In any setting mode, if no button is pressed within 8 seconds, the display will
automatically return to the current temperature display.
PAGE 8
INSTALLATION
DISCONNECT THE POWER SUPPLY AT THE CIRCUIT BREAKER
*
OR FUSE BEFORE PROCEEDING WITH THE INSTALLATION.
Remove the old thermostat
1
2-WIRE INSTALLATION:
carefully and identify the two
Metal Wall Box
wires from the wall box.
Grounding
Screw
2 Using the wire nuts provided, GREEN
Wire Nut
securely fasten each wire from
the new thermostat to a wire in
Wire Nut
the wall box. Refer to the
diagram. NOTE: ENSURE NO
BARE WIRE IS EXPOSED.
Electric
120-240V AC Baseboard
Line Heater
3 Using the GREEN wire nut
provided, securely fasten the
GREEN grounding wire from the
4-WIRE INSTALLATION:
new thermostat to the grounding
Metal Wall Box
wire of the cables and the
Grounding
grounding screw of the wall box.
Screw
Refer to the diagram. GREEN
Wire Nut
Mount the new thermostat into
4
Wire Nut
the wall box using the two screws
provided through the mounting
holes. (Remove the cover if
Electric
necessary). 120-240V AC Baseboard
Line
Heater
5
Reconnect power supply.
PAGE 4
TROUBLESHOOTING
problem solution
Display shows a blank screen. Make sure that the thermostat is fully
installed. Refer to the INSTALLATION
section. Check that the power supply
has been reconnected at the circuit
breaker or fuse. And, if the heater or
heating appliance has a power switch
of its own, check to see that it has
been turned ON.
The thermostat housing is hot. In normal use at full capacity, the
thermostat housing may reach
temperatures of approximately 40°C.
This state is normal and does not
affect the operation.
TECHNICAL SPECIFICATIONS
Rating: 120V ~ 240V AC, 60Hz
Maximum Load: 12.5A; 3000W @ 240V or 1500W @ 120V
Minimum Load: 500W
PAGE 9
DISPLAY / BUTTONS
LCD display
1
1
TEMPERATURE DISPLAY
2
2
TEMPERATURE UNITS ( °C or F) °
F 3
3
TEMPERATURE SETTING MODE
4
HEAT "ON" INDICATOR
4
5
5
OUTPUT POWER LEVEL
button placement
1
UP BUTTON
1
2
DOWN BUTTON
2
PAGE 5
LIMITED THREE-YEAR WARRANTY
UPM warrants this product, excluding battery, to be free from defects in the materials or workmanship, under normal use and
service, for a period of three (3) years from the date of purchase by the consumer.
If, at any time during the warranty period, the product is defective or malfunctions, UPM shall repair or replace it (at UPM's
discretion) within a reasonable period of time.
If the product is defective,
(i) return it, with a dated proof of purchase, to the retailer from which you purchased it, or
(ii) package it carefully, along with a dated proof of purchase and a short description of the malfunction, and mail it, postage
prepaid, to the following address:
UPM Marketing Inc.
Return Goods
Unit 10B - 250 Shields Court
Markham, Ontario
L3R 9W7
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by UPM that the defect or
malfunction was caused by damage which occurred while the product was in the possession of the consumer.
UPM's sole responsibility shall be to repair or replace the product within the terms stated above. UPM SHALL NOT BE LIABLE FOR
ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTL Y
OR INDIRECTLY , FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER F AILURE OF THIS
PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not
apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY UPM MAKES ON THIS PRODUCT . THE DURATION OF ANY IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED TO THE THREE YEAR DURATION OF THIS WARRANTY . Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
If you have any questions concerning this warranty, please write to:
UPM Marketing Inc.
Customer Service Department
Unit 10B - 250 Shields Court
Markham, Ontario
L3R 9W7
Or call 1-888-GO-TO-UPM (1-888-468-6876), Monday to Friday, from 9:00am to 5:00pm eastern.
PAGE 10