Download  Print this page

Motorola LI4278 Product Reference Manual: Batch Mode; Modes Of Operation

General purpose scanner.
Hide thumbs
   
1
2
3
4
5
6
Table of Contents
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450

Advertisement

4 - 24 LI4278 Product Reference Guide

Batch Mode

Parameter # F1 20h
IMPORTANT Batch mode does not apply to SPP Slave Mode.
The linear imager scanner supports three versions of batch mode. When the linear imager scanner is
configured for any of the batch modes, it attempts to store bar code data (not parameter bar codes) until
transmission is initialized, or the maximum number of bar codes are stored. When a bar code is saved
successfully, a good decode beep sounds and the LED flashes green. If the linear imager scanner is unable to
store a new bar code, a low/high/low/high out of memory beep sounds. (See pages
and LED definitions.)
In all modes, calculate the amount of data (number of bar codes) the linear imager scanner can store as
follows:
Number of storable bar codes = 30,720 bytes of memory / (number of characters in the bar code + 3).
If the batch mode selection is changed while there is batched data, the new batch mode will
NOTE
take effect only after all the previously batched data is sent

Modes of Operation

Normal (default) - Do not batch data. The linear imager scanner attempts to transmit every scanned bar
code.
Out of Range Batch Mode - The linear imager scanner starts storing bar code data when it loses its
connection to a remote device (for example, when a user holding the linear imager scanner walks out of
range). Data transmission is triggered by reestablishing the connection with the remote device (for
example, when a user holding the linear imager scanner walks back into range).
Standard Batch Mode - The linear imager scanner starts storing bar code data after Enter Batch Mode
is scanned. Data transmission is triggered by scanning Send Batch Data.
NOTE Transmission is halted if the connection to the remote device is lost.
Cradle Contact Batch Mode - The linear imager scanner starts storing bar code data when Enter Batch
Mode is scanned. Data transmission is triggered by insertion of the linear imager scanner into the cradle.
NOTE If the linear imager scanner is removed from the cradle during batch data transfer, transmission halts until
the linear imager scanner is re-inserted in the cradle.
In all modes, transmissions are halted if the linear imager scanner is moved out of range. The linear imager
scanner resumes when it is back in range. If a bar code is scanned while batch data is transmitted it is
appended to the end of the batched data; parameter bar codes are not stored.
2-1
and
2-5
for all beeper
.

Advertisement

Comments to this Manuals

Symbols: 0
Latest comments: