Download Print this page

Alpine CDE-102 Quick Reference Manual: Indication For Cd Player

Mp3/wma/aac cd receiver.
Hide thumbs

Advertisement

Indication for CD Player
NO DISC
• No CD is inserted.
- Insert a CD.
• Although a disc is inserted, "NO DISC" is displayed and the unit
does not stal1to play or eject the disc.
- Remove the disc by following these steps:
Press the
~
bullon again for at least 2 seconds.
If the disc still does not eject, consult your Alpine dealer.
ERROR
• Mechanism error.
I) Press the
~
bullon and eject the CD.
If not eje:cting, consult your Alpine dealer.
2) When the error indication remains after ejecting, press the
~
button again.
If the error indication still does not tum off after pressing the
~
bullon for a few times, consult your Alpine dealer.
• When "ERROR"' is displayed:
If the disc cannot be ejected by pressing
~,
press the RESET switch
(refer
to
page
6)
and press
~
again.
If the disc still cannot be ejected. consult your Alpine dealer.
PROTECT
• A copy-protected WMA file was played back.
- You can only play back non-copy-protected files.
UNSUPORTED
I
• A sampling ratelbit rate not supported by the unit is used.
- Use a sampling ratelbit rate that is supported by the unit.
ERROR
• Abnormal current is run
to
the USB connector device (an error
message may be displayed if the USB device that is not
compatible with the unit is connected).
USB memory is a malfunction or it is shorted.
- Connect another USB memory.
I
UNIT ERROR
I
• A USB device that is not supported by the unit is connected.
- Connect a USB device that is supported by the unit.
NO DEVICE
• A USB memory is not connected.
- Make sure the USB memory device is correctly connected and
the cable is not excessively bent.
NO FILE
• No song (file) is stored in the USB memory.
- Connect the USB memory device after storing songs (files).
I
UNSUPORTED
I
• A sampling ratelbit rate not supported by the unit is used.
- Use a sampling ratelbit rate that is supported by the unit.
PROTECT
• A copy-protected WMA file was played back.
- You can only play back non-copy-protected files.
NO SUPPORT
I
• Text information that is not recognizable by the unit has been input.
- Use a USB memory device with input text information that is
supported by the unit.
NO IPOD
• The iPhoneliPod is not connected.
- Make sure the iPhone/iPod is correctly connected (refer to
"Connections").
Make sure the cable is not bent excessively.
NO SONG
• There are no songs in the iPhone/iPod.
- Download songs to the iPhone/iPod and connect to this unit.
ERROR-01
• Communication error.
- Tum the ignition key off, and then set to ON again.
- Reset the iPod.
- Check the display by reconnecting between the iPhone/iPod
and this unit, using the iPhone/iPod cable.
ERROR-02
I
• Caused by the iPhoneliPod Software Version not being
compatible with this unit.
- Update the iI'honeliPod Software Version to be compatible with this unit.
ERROR-Qa
I
• The iPhone/iPod is not verified.
- Reset the iPod.
- Try another iPhone/iPod, if available.
ERROR-04
I
• Power surge error.
- Excessive voltage/current is supplied to the iPhone/iPod.
- Try another iPhone/iPod, if available.
Indication, for all Modes
I
DC ERROR
I
• Malfunction occurred as a result of the speaker cable shorting on
the car chassis.
- Route the cable correctly, and set POWER IC to POW ON (page 16).
If the above solution does not work, consult your nearest dealer.
23-EN

Advertisement

   Also See for Alpine CDE-102

   Related Manuals for Alpine CDE-102

Comments to this Manuals

Symbols: 0
Latest comments: