User Manual 2201L Touchmonitor User Manual – 2201L SW601363 Rev A Page 1 of 20...
Page 2
Tyco Electronics. Disclaimer The information in this document is subject to change without notice. Tyco Electronics makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Tyco Electronics reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Tyco Electronics to notify any person of such revisions or changes.
This manual contains information that is important for the proper setup and maintenance of the unit. Before setting up and powering on your new touchmonitor, read through this manual, especially the Installation, Mounting, and Operation chapters. User Manual – 2201L SW601363 Rev A Page 4 of 20...
3-pin to 2-pin adapter for Japan power cable Connector Panel & Interfaces Remove the cable cover on the back of the unit to access the touchmonitor’s connector panel. User Manual – 2201L SW601363 Rev A Page 5 of 20...
5. Replace the cable cover, if desired. Cables can be routed inside the stand – remove and replace the stand cable cover for access and routing. 6. The touchmonitor ships in an OFF state. Press the power button to turn it on. User Manual – 2201L SW601363 Rev A Page 6 of 20...
Page 7
Touch drivers for other operating systems Insert the Elo TouchTools CD into your computer’s CD-ROM drive. The CD should automatically run the Elo TouchTools application. Select “Install Driver for This computer”: User Manual – 2201L SW601363 Rev A Page 7 of 20...
Page 8
For Windows 7 installations, check the “Install driver” box under “Elo USB Interfaces – Other Touchscreens” After accepting the end-user license agreement, the drivers will finish installing. Reboot your computer after the install is complete. User Manual – 2201L SW601363 Rev A Page 8 of 20...
Remove the stand using a Phillips screwdriver to access this mounting interface. The VESA FDMI-compliant mounting is coded: VESA MIS-D, 100, C Stand Mounting Threaded through-holes are provided on the bottom of the stand base for mounting or securing. User Manual – 2201L SW601363 Rev A Page 9 of 20...
This loss of fidelity is most apparent when viewing feature-rich images at close distances (for example images containing small-font text). User Manual – 2201L SW601363 Rev A Page 10 of 20...
H-position, V-position, Clock, and Phase menu items. Only applicable for VGA input video Moves the image horizontally on the display in single-pixel increments. H-position Default: centered. Only applicable for VGA input video User Manual – 2201L SW601363 Rev A Page 11 of 20...
Page 12
Video Source The options are: VGA Priority, DVI Priority Default: DVI Priority All touchmonitor adjustments made through the OSD are automatically memorized as soon as User Manual – 2201L SW601363 Rev A Page 12 of 20...
Page 13
When headphones are plugged into the headphone output jack, the internal speakers turn off and audio is played over the headphones. Volume and muting of the speaker and headphone outputs can be controlled by the OSD. User Manual – 2201L SW601363 Rev A Page 13 of 20...
Visit www.elotouch.com/products for technical specifications for this device Visit www.elotouch.com/go/websupport for online self-help. Visit www.elotouch.com/go/contactsupport for technical support. See this user manual’s last page for worldwide technical support phone numbers. User Manual – 2201L SW601363 Rev A Page 14 of 20...
Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling. User Manual – 2201L SW601363 Rev A Page 15 of 20...
Move the digital device away from the affected receiver. ii) Reposition (turn) the digital device with respect to the affected receiver. User Manual – 2201L SW601363 Rev A Page 16 of 20...
Page 17
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this component is above the limit requirement in SJ/T11363-2006. For items marked with X, exemptions were taken according to EU RoHS. User Manual – 2201L SW601363 Rev A Page 17 of 20...
Page 18
Operating Conditions: Temperature: 0°C - 40°C Humidity: 20% to 80% (non-condensing) Altitude: 0 to 3,048m Storage Conditions: Temperature: -20°C - 50°C Humidity: 10% to 90% (non-condensing) Altitude: 0 to 12,192m User Manual – 2201L SW601363 Rev A Page 18 of 20...
Buyer. Buyer will indemnify Seller and hold Seller harmless from any liability, claims, loss, cost, or expenses (including reasonable attorney’s fees) attributable to Buyer’s products or representations or warranties concerning same. User Manual – 2201L SW601363 Rev A Page 19 of 20...
Need help?
Do you have a question about the 2201L and is the answer not in the manual?
Questions and answers