Yamaha DG-Stomp Service Manual page 30

DG-Stomp
6: DSP Electric Characteristic
• Using the UP and DOWN switches, select "6" and
then press the STORE switch.The output level becomes
the same when the right end No. is "0" and when it is "1".
• The output level, noise level and distortion rate can
be checked by inputting the signal for measurement
(by shorting the input with GND for the noise level check).
• Initial setting: HIGH/LOW SW (SW101) ••• OFF
(LOW), VR ••• Center, OUTPUT VR ••• MAX
ITEM
1. INPUT sensitivity
2. INPUT sensitivity
3. INPUT sensitivity
4. INPUT sensitivity
5. INPUT sensitivity
6. INPUT sensitivity
7. INPUT sensitivity
8. INPUT sensitivity
9. INPUT sensitivity
10. INPUT sensitivity
11. INPUT sensitivity
12. INPUT sensitivity
13. INPUT sensitivity
14. INPUT sensitivity
15. INPUT sensitivity
16. NOISE LEVEL
17. NOISE LEVEL
18. NOISE LEVEL
19. NOISE LEVEL
20. DISTORTION FACTOR
21. DISTORTION FACTOR
22. DISTORTION FACTOR
23. DISTORTION FACTOR
24. Digital Out
F. HOW TO CONFRIM ROM VERSION
Turn on the power while pressing "DOWN" and "MANUAL
SW" switches, and the model name appears as dG.S
for about 2 seconds and then the version number as *.**
also for about 2 seconds. (Each * represents a numeric
figure.) Read that number for confirmation. The normal
mode will then be resumed.
30
INPUT
JK101(INPUT) -5dBm(1kHz)
JK101(INPUT) -5dBm(10kHz)
JK101(INPUT) -5dBm(100Hz)
JK101(INPUT) -25dBm(100Hz)
JK101(INPUT) -25dBm(10kHz)
JK101(INPUT) -25dBm(1kHz)
JK101(INPUT) -5dBm(1kHz)
JK101(INPUT) -5dBm(10kHz)
JK101(INPUT) -5dBm(100Hz)
JK101(INPUT) -25dBm(100Hz)
JK101(INPUT) -25dBm(10kHz)
JK101(INPUT) -25dBm(1kHz)
JK101(INPUT), SW101 ON -35dBm(1kHz)
JK101(INPUT), SW101 ON -35dBm(10kHz)
JK101(INPUT), SW101 ON -35dBm(100Hz)
JK101(INPUT)/No Filter/GND short
JK101(INPUT)/No Filter/GND short
JK101(INPUT)/No Filter/GND short
JK101(INPUT) /No Filter/GND short
JK101(INPUT) /No Filter-5dBm(1kHz)
JK101(INPUT)/No Filter -25dBm(1kHz)
JK101(INPUT)/No Filter -5dBm(1kHz)
JK101(INPUT)/No Filter -25dBm(1kHz)
JK101(INPUT)/No Filter -15dBm(1kHz)
OUTPUT
JK103(OUT L/MONO) +1.0dBm+/-3dB
JK103(OUT L/MONO) +1.0dBm+/-3dB
JK103(OUT L/MONO) +1.0dBm+/-3dB
JK104(OUT R) -1.0dBm+/-3dB
JK104(OUT R) -1.0dBm+/-3dB
JK104(OUT R) -1.0dBm+/-3dB
JK102(HP L) -0.5dBm+/-3dB
JK102(HP L) -0.5dBm+/-3dB
JK102(HP L) -1.5dBm+/-3dB
JK102(HP R) -3.5dBm+/-3dB
JK102(HP R) -2.5dBm+/-3dB
JK102(HP R) -2.5dBm+/-3dB
JK104(OUT R) -0.5dBm+/-3dB
JK104(OUT R) -0.5dBm+/-3dB
JK104(OUT R) -0.5dBm+/-3dB
JK103(OUT L/MONO) -45dBm
JK104(OUT R) -45dBm
JK102(HP L) -45dBm
JK102(HP R) -45dBm
JK103(OUT L/MONO) 0.5%
JK104(OUT R) 0.5%
JK102(HP L) 0.5%
JK102(HP R) 0.5%
JK2(Digital Out) Lch -18dBm+/-3dB Rch 0dBm+/-3dB