Page 1
Wavelength : =790 nm R-6 sized Ni-MH rechargeable battery NH-MDAA (supplied) Emission duration : continuous Sony AC Power Adaptor AC-MZR55 (supplied) connected at the Laser output : less than 44.6 W* DC IN 3V jack Battery operation time * This output is the value measured at a distance of 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.
Mass TABLE OF CONTENTS Approx. 113 g (4.0 oz.) the player only Approx. 155 g (5.5 oz.) incl. a premastered MD and a Sony 1. SERVICING NOTE ............3 alkaline LR6 (SG) battery Supplied accessories 2. GENERAL AC power adaptor AC-MZR55 (1) ...............
SECTION 1 SERVICING NOTE 1. When repairing this de vice with the po wer on, if you remo ve the main boar d, this de vice stops w orking. In this case , you w ork without the de vice stopping b y fastening the hook of the DOOR OPEN/CLOSE s witc h (S801) with tape .
SECTION 3 DISASSEMBLY • The equipment can be removed using the following procedure. Bottom panel assy Main board Upper panel assy Main board MD assy OP service assy Note : Follow the disassembly procedure in the numerical order given. 3-1. BOTTOM PANEL ASSY Note : When installing, fit the knobs and switches.
3-3. MAIN BOARD 4 step screw 3 precision pan (MD) screw (M1.4) 2 precision pan 5 toothed lock screw (M1.4) screw 1 battery case lid 9 MAIN board 7 CN501 8 CN551 3-4. MD ASSY 3-5. OP SERVICE ASSY 1 claw 3 MD assy 3 main shaft 2 OP service assy...
SECTION 4 TEST MODE Outline Configuration of Test Mode • In this set, overall adjustment mode is made a vailab le b y enter - The test mode has the configuration given belo ing test mode to perform automatic adjustment of CD and MO. In the overall adjustment mode, the disc is determined whether + key Overall...
Page 8
2. Description of Each Mode (See page 7.) 010 Offset adjustment Mode Description FE offset TE offset ” key p key MO adjustment All servo ON 0 3 0 020 Laser power adjustment 031 to 039 Mode Description p key MO power A ”...
Page 9
060 Sled movement Audio Mode ” • Enter the test mode and press the VOL – ke y. Then, press the Mode Description key and the VOL + ke y in this turn to enter audio mode Sled in • When entering another mode , ref er to the configuration of test Sled out 5 mode.
Page 10
Power Mode Char ge status code (fir st digit) ” • Enter the test mode and press the VOL – ke y. Then, press the Code Description key and the VOL – ke y in this turn to enter po wer mode .
1. Enter the test mode and press the VOL + ke y to enter o verall adjustment mode. MO FE balance 2. Insert the test CD (TGYS-1) or SONY MO disk (recorded) com- MO ABCD gain mer ciall y a vailab le. MO focus gain 3.
Page 12
* Remote commander display during automatic adjustment 0 5 7 Adjustment value (flashing) Mode No. under adjustment 4. If result of automatic adjustment is OK, the following display appears. End-OK 5. If result of automatic adjustment is NG, the following display appears.
SECTION 6 DIAGRAMS 6-1. IC PIN DESCRIPTION • IC801 RU6815MF-0004 (SYSTEM CONTROL) Pin No. Pin Name Pin Description HIDC MON HIDC voltage monitor input. UREG MON Unreg voltage monitor input. CHG MON CHG voltage monitor input. VREF Reference voltage for power supply voltage adjustlment. PLAY KEY Set PLAY key input.
Page 14
Pin No. Pin Name Pin Description CHG CONT CHG control signal output. CHG PWR CHG power supply voltage control signal output. — Digital power supply (+2.8V). — Power for on board light. — Digital ground. SLD 1R CON Sled motor control signal output. SLD 1F CON Sled motor control signal output.
MZ-E33 6-4. SCHEMATIC DIAGRAM • Refer to page 25 for IC Block Diagrams. • Waveforms (MODE:PLAY) * : The electrical components differ according to the version of the system control IC (IC801). When replacing the IC801, check its model name and add or remove D1001 and/or R1001 as shown below.
Page 18
• IC Block Diagrams IC301 BA3577FS-E2 IC552 TLC372CPWR IC802 AK93C55AV-L IC551 MPC17A55FTA IC501 SN761054 RF IN VREF EF BLANCE/ POWER VREF OUT GENERATOR EXCHANGE RF OUT TRACKING-ERROR BIAS IN ABCD EXCHANGE ABCD INSTRUCTION ADDITION DECODE PRE DRIVER PRE DRIVER PRE DRIVER PRE DRIVER POWER AGND...
SECTION 7 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • -XX and -X mean standardized parts, so • Accessories and packing materials are number in the exploded views are not supplied. they may have some difference from the given in the last of this parts list.
7-3. MECHANISM DECK SECTION (MT-MZE55-150) R1001 M902 M901 The components identified by Les composants identifiés par une mark ! or dotted line with mark. marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une piéce specified.
SECTION 8 MAIN ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by the parts list may be different from the they are seldom required for routine service. mark ! or dotted line with mark.
Page 23
MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C922 1-107-826-11 CERAMIC CHIP 0.1uF L902 1-416-668-11 CHOKE COIL 10uH C923 1-127-688-21 TANT AL. CHIP 10uF 6.3V L903 1-414-410-21 INDUCTOR 10uH C924 1-164-156-11 CERAMIC CHIP 0.1uF < FIL TER > <...
Page 24
MZ-E33 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ( + ) R818 1-216-839-11 MET AL CHIP 1/16W S805 1-771-053-21 SWITCH, KEY BOARD ( R819 1-216-853-11 MET AL CHIP 470K 1/16W S806 1-771-053-21 SWITCH, KEY BOARD (...