Sony DVP-CX777ES Service Manual page 24

DVP-CX777ES
To quit the diagnosis and return to the Check Menu screen,
[ENTER]
press or key. If an error occurred, the diagnosis is
x
suspended and the error code is displayed as shown below.
### Syscon Diagnosis ###
3-2. EEPROM Check
Error 03 : EEPROM Write/Read N
Address : 00000001
Write Data: 2492
Read Data : 2490
Press NEXT Key to Continue
Press PREV key to Repeat
_
Press x key to quit the diagnosis, or
item where an error occurred, or
from the item next to faulty item.
* In "All item continuous check", pressing stop or enter will not
quit the diagnosis.
[2]
Selecting and subsequent items call the submenu screen of
each item. When "———" is displayed in the submenu, it means
that the test is not supported in the model.
For example, if "5. Supply" is selected, the following submenu
will be displayed.
### Syscon Diagnosis ###
Check Menu
No. 5 Supply
0. Quit
1. All
2. ARP Register Check
3. ARP to RAM Data Bus
4. ARP to RAM Address Bus
5. ARP RAM Check
0. (Quit)
Quit the submenu and return to the main menu.
1. (All submenu items continuous check.)
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
Normally, all items are checked successively one after another
automatically unless an error is found.
[2]
Selecting and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see "General Description of
Checking Method" and "Check Items List".
24
. key to repeat the same
> key to continue the check
General Description of Checking Method
2. Version
(2-2) Revision
ROM revision number is displayed.
Error: Not detected.
The revision number defined in the source file is displayed
with four digits.
(2-3) ROM Check Sum
Check sum is calculated.
Error: Not detected.
8-bit data are added up to the ROM address 0x000F0000 to
0x002EFFFF, and the result is displayed with 4-digit hexa-
decimal number. Error is not detected. Compare the result
with the specified value.
(2-4) Model Type
Model code is displayed.
Error: Not detected.
The model code read from the EEPROM is displayed with
2-digit hexadecimal number.
(2-5) Region
Region code is displayed.
Error: Not detected.
The region code determined from the model code is dis-
played.
(2-6) M't Check
Mount resistance is checked.
Error 22: The region code does not accord.
Check whether the region code that is deduced from model
resistance and destination resistance accords with the re-
gion code that is deduced from region resistance value.
3. Peripheral
(3-2) EEPROM Check
Data write t read, and accord check
Error 03: EEPROM write/read discord
0x9249, 0x2942 and 0x4294 are written to the address 0x00
to 0xFF of the EEPROM and then read for checking. Be-
fore writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
(3-3) Gate Array Check
Data write → read, and accord check
Error 02: Gate Array write/read discord
Data of 0x00 to 0xFF is written sequentialy to the address
0xF and then read for checking.
(3-4) NAND FLASH Check
Data delete → write → read, and accord check
Error 04: delete error
Error 05: write error
Error 06: read data discord
Error 21: more than ten blocks are defective
Deleting, writing and checking read data are executed to
the zeroth block of Flash memory.
If any detective block is found, the address is displayed.
When more than ten blocks are defective, it is considered
as an error.
(3-5) SACD Check
Device reset t internal organs RAM check.
Error 50: Write and read data discord.