Mains Supply - Hitachi HTD-K160 Instruction Manual

DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards:
EN60065, EN55013, EN55020, EN61000-3-2 and EN6100-3-3.
Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC directives.
The mains lead on this equipment may be supplied with a moulded plug incorporating a fuse, the value of which is indicated on
the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS1362 fuse must be used of the same
rating. If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure
it is of the same colour as that visible on the pin face of the plug. Fuse covers are available from your dealer.
DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too
short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
Should it be necessary to change the mains plug, this must be carried out by a competent person, preferably a qualified electrician.
If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid
a possible shock hazard by inadvertent connection to the mains supply.
IMPORTANT
As these colour may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:
The wire coloured WHITE must be connected to the terminal marked with the letter FL. The wire coloured RED must be
connected to the terminal marked with the letter FR. The wire coloured GREEN must be connected to the terminal marked with
the letter C. The wire coloured BLUE must be connected to the terminal marked with the letter SL. The wire coloured GREY must
be connected to the terminal marked with the letter SR.
WARNING:

Mains supply:

This DVD player can be used with a power (mains) voltage of 230V.
The OPERATE button is indicated "
standby.
Notice:
The OPERATE button is secondarily connected and does not separate the apparatus from the mains
supply in the switched-off position.
CONNECTION TO POWER (For the area of Great Britain)
Before Switching on make sure that the voltage of your elec-
tricity supply is the same as that indicated on the rating plate.
Mains Cord
This appliance may be fitted with a non-rewircable plug. If it is
necessary to change the fuse in a non-rewircable plug the
fuse cover must be refitted. If the fuse cover is lost or damaged,
the plug must not be used until replacement available from
the appliance manufacturer is obtained.
It is important that the colour of the replacement fuse cover
corresponds with the rating marking on the base of the plug.
It the plug has to be changed because it is not suitalble for
your socker, or becomes damaged, it should be cut off and
an appropriate plug fitted following the wiring instructions
below, The plug removed must be disposed of safely as in-
sertion into a 13A socket is likely to cause an electrical hazard.
For your own safety read the following instructions carefully
before attempting to connect this unit to mains.
The wires in this mains lead are coloured in accordance with
the following code:
BLUE=NEUTRAL, BROWN=LIVE
2
IMPOR IMPORT T T T T ANT IMPOR ANT ANT ANT
IMPOR IMPOR ANT
"; this button allows you to select operate on or electrical power
Important
As the colours of the wires in the mains lead of the appliance
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows: The wire which
is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
No connection is to be made to the earth terminal of the plug.
If a 13 Amp (BS 1363) Plug is used, a 3 Amp Fuse must be
fitted, of if any other type of Plug is used a 3 or 5 Amp Fuse
must be fitted, either in the Plug or Adaptor, or on the Distribu-
tion Board.
Mains Supply: 220 - 240 V-50 Hz - AC only
Do not make any connection to the larger pin marked with the
letter "E" or by the symbol
yellow.
or coloured green or green and