Advertisement
Operation Guide 3402
3. When the setting you want to change is flashing, use B and D to change it as
described below.
Setting
Screen
Use D (+) and B (–) to change the setting.
Hours, Minutes
Press D to toggle auto-repeat on (
Auto-repeat
(
displayed).
Press D to toggle the progress beeper on (
Progress Beeper
• To specify a countdown start time of 24 hours, set
4. Press A to exit the setting screen.
• You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
E-20
Alarms
You can set up to five independent multi-function alarms
Alarm date
with hour, minutes, month, and day. When an alarm is
(Month – Day)
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms is a snooze alarm, while the
Alarm number
other four are one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered
, and
screen indicated by
screen is indicated by
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
Alarm time
(Hour : Minutes)
E-7).
Alarm on indicator
E-22
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set a one-time alarm, display an alarm screen
To set the snooze alarm, display the
• The snooze alarm repeats every five minutes.
E-24
Alarm Operation
The alarm tone sounds at the preset time for 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-24)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-26
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator (
the display in all modes while this function is turned on.
Hourly time signal
on indicator
E-28
Button Operation
displayed) and off
) and off (
).
.
,
,
for the one-time alarm, a snooze alarm
. The Hourly Time Signal
.
,
,
, or
.
screen.
).
) is shown on
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
• The countdown timer operation continues even if you
exit the Countdown Timer Mode.
• Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
• To stop a countdown operation completely, first pause it
(by pressing D), and then press A. This returns the
countdown time to its starting value.
Alarm Types
The alarm type is determined by the settings you make, as described below.
• • • • • Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• • • • • Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• • • • • 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
• • • • • Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing in the sequence shown below to select other settings.
Hour
Minutes
4. While a setting is flashing, use D and B to change it as described below.
Screen
To do this:
Do this:
Use D (+) and B (–).
Change the hour
and minutes
• With the 12-hour format, set the time correctly as a.m.
or p.m. (P indicator).
Change the
• To set an alarm that does not include a month and/or
month and day
day, set
5. Press A to exit the setting screen.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
displays the alarm on indicator (
• In all modes, the alarm on indicator is shown for alarm
that is currently turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator (
Snooze alarm
indicator
snooze alarm is sounding and during the 5-minute
intervals between alarms.
World Time
World Time shows the current time in 48 cities (29 time
City code
zones) around the world.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C
(page E-7).
To view the time for another city code
In the World Time Mode, press D to scroll eastwardly
through city codes.
• For full information about city codes, see the "City Code
Table" at the back of this manual.
Current time and date in
• If the current time for a city is wrong, check your
the zone of the selected
Timekeeping Mode time and time zone settings and
city code
make necessary changes.
E-21
E-23
Month
Day
for each setting.
E-25
,
,
,
, or
)
,
).
) flashes while the
E-27
E-29
Advertisement
