DVDCAM PC Software Support Center URL http://dvdcam-pc.support.hitachi.ca/ Thank you for buying a Hitachi product. Please take time to become familiar with the manual and how it is set up. Keep it handy for future reference. Be sure to read page 187 before unpacking the provided CD-ROM.
Important Information For Your Safety The power switch turns the DVD video camera/recorder on and off, leaving the date/time feature unaffected. If the camera/recorder is to be left unattended for a long period of time, turn it off. WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Page 3
Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFEGUARDS In addition to the careful attention devoted to quality standards in the manufacture of your video product, safety is a major factor in the design of every instrument. But, safety is your responsibility too. This page lists important information that will help to assure your enjoyment and proper use of DVD video camera/ recorder and accessory equipment.
Page 5
An appliance and cart combination SERVICE should be moved with care. Quick Servicing — Do not attempt to service this video stops, excessive force, and uneven product yourself as opening or removing covers may surfaces may cause the appliance expose you to dangerous voltage or other hazards. and cart combination to overturn.
Cautions When Using Handle the liquid crystal display (LCD) with care: • The LCD is a very delicate display device: Do not press its surface with force, hit it or prick it with a sharp object. • If you push the LCD surface, unevenness in display may occur. If unevenness does not disappear soon, turn the DVD video camera/recorder off, wait for a few moments, and then turn it on again.
Page 7
Heat on surface of product: • The surface of the DVD video camera/recorder will be slightly warm, but this does not indicate a fault. Screen on connected TV: • Never leave the disc navigation screen, still image or camera image displayed on your TV to which the DVD video camera/recorder is connected: Doing so could result in displayed image retention or phosphor degradation of TV screen.
Page 8
Be careful of moisture condensation: • When you move the DVD video camera/recorder between places where the difference in temperatures is great - such as entering a lodge from a ski slope or going out of a cooled room or vehicle - condensation (vapor in air warmed or cooled to water droplets) could occur on the lens and/or inside the DVD video camera/recorder.
The recorded contents cannot be compensated for: • Hitachi cannot compensate for any damages caused when recording is not made normally or recorded contents cannot be played back because of a defect in the DVD video camera/recorder, disc or card.
Refer to these marks and identify the functions and operation to match the disc or card you use. Illustrations in this manual Although the external appearances of DZ-MV550A and DZ-MV580A are different, the method of operating both models is identical.
Introduction You can start recording immediately after stopping playback (P.49, 58) Unlike tape devices, you do not need to search for the recording start position or locate the beginning of blank portion. You can stop playback and immediately start recording: New recording will not overwrite any previously recorded data.
Page 12
You can easily edit scenes, which is Create original DVDs on PC (P.152) quite difficult with tape (P.86) You can use a DVD-R disc to create an original DVD, using the provided software CD-ROM. Using this DVD video camera/recorder, you can The created DVD disc can be played back on DVD collect scenes of your child, for example, on play player, DVD-ROM drive, etc.
Table of Contents Important Information ........2 CHARGING BATTERY ........39 ATTACHING BATTERY TO DVD VIDEO For Your Safety ..........2 CAMERA/RECORDER ........40 Precautions ............2 REMOVING BATTERY........40 IMPORTANT SAFEGUARDS ......4 BATTERY REMAINING LEVEL INDICATOR ..42 Cautions When Using ........6 EFFICIENT USE OF BATTERY ......42 USING DVD VIDEO CAMERA/RECORDER Cautions When Storing ........9 WITH AC ADAPTER/CHARGER......43...
Page 14
FLOW OF QUICK MODE (WITH CARD): ... 70 SETTING COLOR DENSITY OF LCD SCREEN (COLOR LEVEL) ......101 Manually Focusing Subject......71 Initial Settings ..........102 FOCUSING DURING RECORDING ....71 SWITCHING OPERATING SOUND ON OR Adjusting Brightness of Image to be recorded OFF (BEEP)............
Page 15
ADDING SCENES TO PLAY LIST Subsidiary Information (EDITING PLAY LIST) ........128 Introduction to Optional Accessories..... 157 DELETING SCENES FROM PLAY LIST CAMERA ACCESSORIES ........157 (EDITING PLAY LIST) ........129 POWER SUPPLY ..........157 ADDING SCENES USING SUBMENU FOR EDITING (EDITING PLAY LIST) ....129 INFORMATION ON SQUARE ADAPTER ..157 Cleaning ............
Checking Provided Accessories Make sure that you have all the following accessories in package: Battery (model DZ-BP14S): AC adapter/charger (model DZ-ACS1): DC power cord: Portable power supply for this DVD video Used to power the DVD video camera/ When powering the DVD video camera/ camera/recorder.
The red indicator will light during recording. 11 2.5" type liquid crystal display (inside) 4 Stereo microphone (P. 76) (P. 35) 5 Optical 18× zoom lens (DZ-MV550A) 12 QUICK MODE switch (P. 63) Optical 10x zoom lens (DZ-MV580A) To switch the menu display on screen between (P.
Page 18
14 Viewfinder (P. 34) 19 CARD ACCESS indicator (P. 8, 50) 15 Diopter control (P. 34) 20 Card insertion block (P. 47) To adjust the focus of image appearing in the 21 Battery attachment platform (P. 40) viewfinder. (Pull out the viewfinder.) 22 Record button (REC) (P.
Page 19
29 30 27 FULL AUTO button (P. 74) 36 RESET button (P. 181) To switch the DVD video camera/recorder to To reset all settings to defaults (status when the full automatic. DVD video camera/recorder was shipped from the factory) 28 FOCUS button (P. 71) To switch between manual focus and auto- 37 PC connection terminal (TO PC) focus.
Page 20
DIGITAL ZOOM ZOOM DISC NAVIGATION DISPLAY MENU SELECT DELETE DZ-RM3W 40 REC button (P. 49, 50) 46 ZOOM T button (P. 56) 41 DIGITAL ZOOM button (P. 56) 47 ZOOM W button (P. 56) 42 Reverse skip button (P. 60) 48 Forward search button (P.
Try to Record and Play Back using Disc (Video and Photo) • It is recommended that you use a DVD-RAM disc for trial recording, since Before You Begin you can delete the recorded contents (P. 25). You can record both videos and photos on DVD-RAM disc; only videos on DVD-R disc. Connect a power supply (P.
Page 22
Start recording (P. 49). 1Open the LCD monitor (P. 35). 3Press the REC button. Recording will start. Pressing the REC button again will stop recording (O VIDEO). Pressing REC will enable you to record one photo (N PHOTO). 2While holding the gray switch at the center of power switch, set the switch to “O VIDEO”...
Try to Record and Play Back using Card (Photo) Only photos can be recorded on card. Connect a power supply (P. 43). Power cable AC adapter/charger DC power cord Insert a card (P. 47). 1Open the cover of card insertion block with 3Insert the card all the way until it locks, and power turned off.
Page 24
Start recording (P. 50). 1Open the LCD monitor (P. 35). 3Press the REC button. Pressing REC once will record one photo. 2While holding the gray switch at the center of power switch, set the switch to “PPHOTO”. Note See Check 2 on P. 163 if recording is not possible with “ PHOTO”.
It is recommended that you use Hitachi Maxell discs, since their compatibility with this DVD video camera/ recorder has been confirmed. Using a disc other than those made by Hitachi Maxell may not allow the DVD video camera/recorder to deliver optimum performance.
INFORMATION ON DVD-R DISC You cannot record a still on DVD-R disc, or delete Finalizing DVD-R disc any recorded images or data. Before using the 8 cm DVD-R disc provided on this For optimum recording on DVD-R disc, this DVD DVD video camera/recorder on a DVD player or video camera/recorder writes control data to the DVD video recorder that is compatible with 8 cm...
HANDLING DISCS Using discs • Be careful when removing the disc since the metal of removal slot of DVD video camera/ DVD-RAM and DVD-R discs are very delicate recorder, and disc itself, may be hot. recording media. Carefully read the following cautions and observe them: Storing discs •...
AVAILABLE CARDS Common cautions for disc and card • It is recommended that you create a backup file SD memory card for valuable data on hard disk of PC. and MultiMediaCard • Do not do the following, or the data on card may can be used on this be damaged or lost: DVD video camera/...
Storage Capacity on Disc or Card RECORDABLE TIME OF MOVIE (VIDEO) The recordable time will vary depending on the video recording quality: See page 96 for the setting of video recording quality. Movie recordable time on one disc (on single side) (when recording only movies) Disc used Recording quality Application...
Setups This section explains preparations for recording - setting up the DVD video camera/recorder and battery. Setting Up the DVD Video Camera/Recorder HOLDING DVD VIDEO CAMERA/RECORDER Insert your right hand from the bottom of DVD video camera/recorder up to the base of your thumb. Put your hand in a position where you can easily operate the REC button and the Zoom lever.
ATTACHING SHOULDER STRAP Be sure to pass through the 2 slots. Pass the shoulder strap through the shoulder strap attachments. ATTACHING LENS CAP Attach the shorter end of lens cap string to the lens cap. Shorter end Attach the longer end of lens cap string to the attachment hole of DVD video camera/ recorder.
Warning Note • • KEEP THE BATTERY AWAY FROM CHILDREN AND Replace the battery with a Hitachi Maxell, Sony, PETS. Panasonic, Sanyo, Toshiba CR2025, or Duracell • IF SWALLOWED CONSULT A PHYSICIAN DL2025. Use of another battery may present a risk of fire IMMEDIATELY FOR EMERGENCY TREATMENT.
The DVD video camera/recorder uses the “VCR2” When using the remote control, make sure that the remote control code of Hitachi VCRs. If you use a Hitachi infrared receiver on DVD video camera/recorder is not VCR, etc. with remote control code set to “VCR2”, a VCR exposed to direct sunlight or any intense light.
VIEWING IMAGE ON LCD MONITOR SCREEN If you open the LCD monitor, you can monitor subject image on the LCD screen. Open the LCD monitor. The LCD monitor has a portion where you can hook your finger. Hook the finger there to open the monitor.
CLOSING LCD MONITOR Before closing the LCD monitor, be sure to reset it Note at right angles to the DVD video camera/recorder. • Be sure to return the LCD monitor at right angles to the DVD video camera/recorder before closing it or Replace the LCD monitor on the DVD video replacing it on the DVD video camera/recorder with its screen facing outside.
SETTING DATE AND TIME Set the current date and time so that the date and time you make a recording can be recorded correctly. The following procedure can also be used to correct the date and time you have already set. Tilt up/down and to left/ right to select, and then press...
CHANGING DISPLAY FORMAT OF DATE AND TIME You can select one of three date display formats: month/day/year, day/month/year or year/month/ day. Associated with the selected date display, the time display format will also change as follows: Date display format Example of display 5:00PM M/D/Y 9/30/2004...
Setting Up the Battery The DZ-BP14S battery provided with this DVD video camera/recorder has not been charged at purchase time: Charge it before using the DVD video camera/recorder. Note • Be sure to use the DZ-BP14S, DZ-BP14SW (optional) battery for the DVD video camera/recorder: Using other batteries could cause the DVD video camera/recorder to malfunction, or result in fire.
Battery charged status You can find out the charged status of battery by checking the CHARGE indicator on AC adapter/charger: Charge status CHARGE indicator During charge Charge complete Goes out Note See “Troubleshooting” on page 172 when the CHARGE indicator blinks. Reference for time required to charge battery (at approx.
Page 41
DVD video camera/recorder can continuously available when the DVD video camera/recorder is be used with a fully charged battery: in the recording mode without using any other For DZ-MV550A function after recording is started. In actual recording, the battery will discharge 2-3 times Video...
BATTERY REMAINING LEVEL INDICATOR When the battery is used to power the DVD video camera/recorder, the battery remaining level appears in the viewfinder or on the LCD screen as follows: Fully charged Nearly empty (Blinks) White portion shows remaining level Note The remaining level indicator “...
USING DVD VIDEO CAMERA/RECORDER WITH AC ADAPTER/CHARGER It is recommended that you use the AC adapter/charger to power the DVD video camera/recorder from household AC outlet when you perform settings on it, play back or edit images, or use it indoors. Note Be sure to use the specified AC adapter/charger (DZ-ACS1) to power the DVD video camera/recorder.
Inserting and Removing Disc INSERTING DISC Press down the DISC EJECT button once and Correct Incorrect release it. orientation orientation A few moments after the ACCESS/PC indicator blinks, the cover of disc insertion block will open slightly. Gently open the cover by hand until it stops. Insert the disc, in Round DVD Holder, into the disc guide until it stops.
Page 45
When using brand-new DVD-R disc Note • Disc cannot be inserted or removed unless a charged Recognition of the disc will battery or AC adapter/charger is connected to the DVD F o rma t D i s c start. video camera/recorder. The messages on the right D i s c i s n o t f o r m a t t e d .
REMOVING DISC Set the power switch to Note • “POWER OFF” to turn the Even after the DVD video camera/recorder is turned on, the disc can be removed unless it is in recording status. DVD video camera/ Hold down the DISC EJECT button for approximately 2 recorder off.
Inserting and Removing Card Turn the DVD video camera/recorder off. Removing Card: Push the center of card Open the cover of card edge. insertion block. The card will come out so that it can be held by fingers. Inserting Card: Insert card with its terminal inward until it locks.
Basic Techniques This section explains about recording of movies and still images, and also basic settings on DVD video camera/recorder. Basic Handling of DVD Video Camera/Recorder TURNING DVD VIDEO CAMERA/RECORDER ON AND OFF While holding down the gray button at the center Note •...
DVD video camera/recorder on. “Setting Up Camera Functions” on page 90. • After the ACCESS/PC indicator goes out, Hitachi cannot be responsible for video and audio that cannot be recorded or edited because of any defect. perform the subsequent operation: •...
Recording Stills Check the subject on the screen (viewfinder or Note LCD). Recording of still images is possible on DVD-RAM disc and card. Press the REC button. CARD ACCESS/PC ACCESS indicator indicator The DVD video camera/recorder automatically focuses on the subject at the center of screen (when auto focus is selected).
Compensating for Backlight When subject is lighted from rear, this function will compensate for lighting so that the subject is not too dark. Press the BLC button during recording. 0 : 0 0 : 0 0 3 0 MIN Backlight correction icon 8 : 0 0 AM FINE 9 / 3 0 / 2 0 0 4...
On-Screen Information Various types of information will appear in the viewfinder or on the LCD screen during recording. INFORMATION DISPLAY DURING RECORDING See the next page for details. 2. Program AE 7. Microphone filter 3. White balance 8. 16:9 mode 4.
Page 53
Manual focus : (display in French or Italian): (Digital Zoom: 40×) Manual focus : (display in Spanish): Manual focus (Digital Zoom: 500× (DZ-MV550A), 240× (DZ-MV580A), only in movie Backlight compensation (P.51) recording mode) No display: Backlight compensation OFF Disc/Card type...
The volume can be adjusted during external input and playback. EIS cannot be used when recording stills on DZ-MV580A. Not displayed on DZ-MV550A. Displayed on DZ-MV580A only when a DVD-RAM disc is used in the movie recording mode. Not displayed on DZ-MV550A.
Display when recording an image of yourself When recording with the LCD screen facing the same direction as the lens, the operating status will appear, and in addition, the battery remaining level will blink when the battery has almost no remaining charge. The following operating status indicator will light or blink to give warning message to user.
“240x” (on DZ-MV580A): Pressing the button during still recording will switch between “Off” and “40×”. • W: recording wide area If you set zoom to 500× (DZ-MV550A), 240× (DZ- (wide-angle) MV580A) when recording still, the digital zoom will be up to 40×.
MACRO RECORDING Use the macro function when recording a small object from close-up position: You can shoot the subject as close as approximately 13/16” (2 cm) from the lens surface, magnifying the image to fill the screen. Aim the DVD video camera/recorder at the Note •...
Playing Back • Insert a disc or card recorded on this DVD video camera/recorder (P. 49, Before You Begin 50). • Turn the DVD video camera/recorder on (P. 48). PLAYING BACK Note • If the LCD monitor is open during playback of movie, playback sound will be heard from the speaker.
PLAYBACK FROM START OF DISC OR CARD Use the Go To function (P. 61) or Disc Navigation function (P. 105) to play back from the start of disc or card. SEARCH PLAYBACK OF MOVIE During playback, tilt the joystick to right or left Note •...
SKIP PLAYBACK OF MOVIE During playback, tilt the joystick up or down to Portion being played back locate the start of desired scene. Tilt down once : To skip to the first image of the Tilt up twice Tilt up once Tilt down once Tilt down twice scene following the one being...
JUMPING TO SPECIFIED POINT (GO TO) Press the MENU button : To go to the start, and enter playback Go T o during playback. pause. To p En d : To go to the end of last scene, and enter S p e c i f y Choose the option (point playback pause.
On-Screen Information Display INFORMATION DISPLAY DURING PLAYBACK Various types of information on recording will be superimposed on playback image you are viewing. No display Playback information Recording date/time display O (VIDEO) or N (PHOTO); Only N (PHOTO) Switching the information display with card.
Checking Flow of Quick Mode The following two on-screen menu modes are available with this DVD video camera/recorder: • Quick mode: To display only the fundamental menu items for first timers • Advanced mode: To display all menu items for experts (P.87) Camera Functions Set the QUICK MODE switch to ON, and then, while the camera image is being displayed on the...
FLOW OF QUICK MODE WHEN RECORDING MOVIE: The following shows the menu when DVD-RAM disc is being used: The details of each function are described on the pages showing the Advanced mode: See each reference page. Record Functions Setup (P. 96) R e c o r d F u n c t i o n s S e t u p R e c o r d F u n c t i o n s S e t u p R e c o r d F u n c t i o n s S e t u p...
FLOW OF QUICK MODE WHEN RECORDING PHOTO (DISC): The following shows the menu when DVD-RAM disc is being used: The details of each function are described on pages showing the Advanced mode: See each reference page. Record Functions Setup (P. 98) R e c o r d F u n c t i o n s S e t u p R e c o r d F u n c t i o n s S e t u p R e c o r d F u n c t i o n s S e t u p...
FLOW OF QUICK MODE WHEN RECORDING PHOTO (CARD): The details of each function are described on pages showing the Advanced mode: See each reference page. Record Functions Setup (P. 97) R e c o r d F u n c t i o n s S e t u p R e c o r d F u n c t i o n s S e t u p R e c o r d F u n c t i o n s S e t u p Qu a l i t y...
Disc Navigation Functions Set the QUICK MODE switch to ON, and then, while Disc Navigation screen is being displayed on the LCD monitor, press the MENU button: The menu of Quick mode will appear. Only the fundamental menu items will appear in the Quick mode, and the explanation of the function on which the cursor is positioned will be displayed across the bottom of menu (except during recording).
FLOW OF QUICK MODE (WITH CARD): The details of each function are described on pages showing the Advanced mode: See each reference page. (P. 111) S c e n e S c e n e D e l e t e D e l e t e D e l e t e s e l e c t e d p h o t o.
Manually Focusing Subject The DVD video camera/recorder usually focuses on a subject automatically (autofocus). You can also manually focus a subject depending on the recording conditions. FOCUSING DURING RECORDING Normally, the DVD video camera/recorder automatically focuses the subject (auto-focus), but you can also manually focus a subject, depending on the recording conditions (manual focus).
Page 72
Manually focus the following objects, which may not be automatically focused (see page 71): Objects not in Objects with Objects that the center of little variation are far and screen in brightness, near at the such as white same time wall Objects Objects lit by...
Adjusting Brightness of Image to be recorded (Exposure) The DVD video camera/recorder usually adjusts the exposure automatically. You can also manually adjust the exposure depending on the recording conditions. Press the EXPOSURE button during recording. The exposure indicator will appear on the screen.
Using Full Auto Function Pressing the FULL AUTO button will fully automate the camera functions. Press the FULL AUTO button. “FULL AUTO” will be displayed on the screen of DVD video camera/recorder for several seconds. The following settings will reset to defaults: When setting Reference Function...
Doing so could dazzle the driver, causing an brightness accident. • No light emission Do not use the Video Flash in a place where there is flammable or explosive gas: Doing so could cause fire or explosion. * Unusable on DZ-MV550A.
USING EXTERNAL MICROPHONE Connect external microphone (generally available) to the external microphone jack of this DVD video camera/recorder. Clearer sound can be recorded. Turn on the switch on external microphone and start recording. For details on external microphone, see “Major Specifications” on page 182. To external microphone jack Note...
Viewing on TV Screen CONNECTING TO A TV Use the provided AV/S input/output cable to connect the DVD video camera/recorder to a TV as follows: To S-video input jack* To video/ To AV input/output jack audio input jacks White AV/S input/output cable Yellow (provided) *If your TV has an S-VIDEO input jack, you can connect the S-VIDEO plug to it.
DVD video camera/recorder while viewing an image on Refer to the TV instruction manual for how to TV screen. However, if you use a Hitachi VCR, the switch the TV input. remote control may inadvertently operate the VCR if it is near the DVD video camera/recorder.
Playback on DVD Video Recorder/Player PLAYING BACK DVD-RAM DISC You can use a DVD video recorder (see “Terminology”, P. 160) or DVD player that conforms to DVD-RAM to play back 8 cm DVD-RAM discs recorded on this DVD video camera/recorder. Remove the disc from Round DVD Holder.
PLAYING BACK DVD-R DISC Finalize a recorded DVD-R disc. Insert the disc into the DVD player and play it back. You need to finalize a disc to play it back on DVD player: See page 137. See the instruction manual for DVD player. No further data can be recorded on finalized disc.
Holder and use the uncovered disc on DVD player, DVD video recorder, or drive for PC, etc. which conforms to 8 cm DVD-R. Removing disc from Round DVD Holder may vary with the disc maker: See the disc instruction sheet. The following explains the disc in Round DVD Holder made by Hitachi Maxell.
REPLACING DISC IN ROUND DVD HOLDER Open SIDE A of the Round DVD Holder, and Close SIDE A of the Round DVD Holder, and replace the disc in the holder with the SIDE A push it to lock the release levers at positions (3). mark or label surface facing up, taking care not to touch the disc surface.
Recording (Dubbing) Images • Before connecting this DVD video camera/recorder to another device, be sure to turn both devices off. Before You Begin • Insert a recordable disc or card* in this DVD video camera/recorder (see P . 25, 28). Only photos can be recorded: No video can be recorded.
Page 84
AC outlet using the AC adapter/charger. • If you use a Hitachi VCR, it will be operated by the remote control provided with the DVD video camera/recorder. When recording an image from a Hitachi VCR, change the remote control code of the VCR to other than “VCR2”.
RECORDING (DUBBING) IMAGES FROM OTHER VIDEO CAMERAS You can record (dub) images from other video cameras on a disc or card* in DVD video camera/recorder. Use the AV/S input/output cable (provided) to connect the DVD video camera/recorder to the other video camera.
• If you are using a Hitachi VCR, using the remote control provided with this DVD video camera/recorder may operate the VCR. To record (dub) images from the DVD...
Advanced Techniques This section explains about various settings to further extend the usefulness of this DVD video camera/ recorder. Checking Flow of Normal Display Mode The following two on-screen menu modes are available with this DVD video camera/recorder: • Quick mode: To display only the fundamental menu items for first timers (P.63) •...
*2: Displayed only in “ VIDEO” status. B r i gh t n e s s Co l or L e v e l *3: Not displayed on DZ-MV550A. Displayed on DZ- MV580A only for movies using DVD-RAM disc. ENTER RETURN Brightness (P.
You can use the joystick on DVD video camera/recorder to select various setting options in menu and designate them. Press the MENU button. Tilt to right Press Came r a Fun c t i ons Se t up Camer a F u nc t i on s S e t u p P r o g r am AE : Au t o Auto...
Setting Up Camera Functions • See page 89 for how to set. Before You Begin • No menu screen appears with external input. SELECTING SHOOTING MODE TO MATCH THE SUBJECT (SWITCHING PROGRAM AE MODE) This DVD video camera/recorder automatically detects the status of subject and surrounding situation and records the optimum image: If you choose the shooting mode to match the recording conditions, clearer images will be recorded.
ADJUSTING COLOR (WHITE BALANCE) This DVD video camera/recorder automatically Note adjusts the color of subject. Change the white • The white balance mode can be confirmed using the on- screen information. balance setting depending on the recording • The white balance setting will be stored in memory even conditions.
Setting white balance manually Point the DVD video camera/ recorder at a white object so that it fills the screen. Use an object that is not transparent. If focus is not correct Thick paper when the white object fills the screen, manually focus the object, referring to “Manually Focusing Subject”...
USING THE ELECTRONIC IMAGE STABILIZER (EIS) When you use zoom to record a magnified subject image, it will correct fuzziness in the recorded image. Press the MENU button, After recording with EIS set to “Off”, it is Came r a F u nc t i on s Se t u p choose “EIS”...
SETTING TO WIDE TV SCREEN MODE (16:9 MODE) If you view the images recorded with “16:9 On” specified on a wide-screen TV (aspect ratio 16:9), screen image will be wider than the images recorded with “16:9 Off” (aspect ratio 4:3) by the size of the areas on left and right (in dotted lines).
Page 95
The 16:9 setting will be kept even after the DVD video camera/recorder is turned off. • The DZ-MV550A does not have the 16:9 setting. • The 16:9 setting can be used when recording movies on DVD-RAM disc: It is not compatible with still recording, recording of external input or recording on DVD-R disc.
Setting Up Record Functions SWITCHING MOVIE QUALITY (VIDEO MODE) Choose the movie quality from “XTRA” (only with DVD-RAM disc), “FINE”, “STD” and “LPCM” (only with DVD-R disc). It is recommended that you record critical subjects in the “XTRA” or “FINE” when you are using a DVD- RAM disc, or in the “FINE”...
Block-like noise may appear in recorded image, or the outline of subject image is distored under the recording conditions listed below: Pan the DVD video camera/recorder as slowly as possible. (Block noise is likely to appear in the “STD”): • If there is a complicated pattern in background (as in following figure on left) •...
RECEIVING IMAGE FROM ANOTHER DEVICE (INPUT SOURCE) If you wish to input an image from another device to this DVD video camera/recorder, you must first switch the setting on the DVD video camera/recorder. Refer to the explanation starting from page 83 on how to connect the DVD video camera/recorder to other devices or record images input from them.
SELF-TIMER You can record photos using the self-timer function, as with ordinary cameras. The self-timer function is valid only when recording photos (stills). Press the MENU button, Press the REC button. Re c o r d F u nc t i on s S e t u p choose “Self Timer”...
SETTING ON-SCREEN DISPLAY OUTPUT ON OR OFF (OSD OUTPUT) If you connect this DVD video camera/recorder to a TV to view images on TV screen, you can switch off the on-screen information (displayed in the viewfinder or on the LCD screen) from the TV screen. Press the MENU button, Press the MENU button to end the setting.
LCD Setup SETTING BRIGHTNESS OF LCD SCREEN (BRIGHTNESS) Press the MENU button, LCD S e t u p choose “Brightness” on the “LCD Setup” menu screen, and then press B r i gh t n e s s Co l o r L e v e l the A button.
Initial Settings SWITCHING OPERATING SOUND ON OR OFF (BEEP) Setting Content Beep is heard when the power switch is changed over, the REC button is pressed, etc. No beep is heard. Select “On” or “Off”, and then press the A Press the MENU button, I n i t i a l S e t u p choose “Beep”...
TURNING RECORD LED ON OR OFF (RECORD LED) You can switch off the recording indicator on the front of DVD video camera/recorder even during recording. Setting Content The recording indicator will light red to show that the DVD video camera/recorder is recording. The recording indicator will not light even during recording.
RESETTING MENU SETTINGS TO DEFAULTS (RESET) You can restore menu settings to defaults (initial settings at the factory (P. 181)). (Note, however, that the date/time will not be reset.) Press the MENU button, Press the MENU button to end the setting. I n i t i a l S e t u p choose “Reset”...
Disc Navigation Using Disc Navigation STARTING OR TERMINATING DISC NAVIGATION Disc Navigation is a tool for editing scenes recorded on this DVD video camera/recorder. Here is an explanation on “scene” and “program”, so that you will be able to make most use of Disc Navigation function.
Page 106
Thumbnail (see “Terminology”, P. 160) Selected scene number A l l Pr og r ams 0 01 / 014 Number of all scenes Cursor Current page position Bar graph Still image icon PLAY Operation guide Disc type icon Scene number refers to display number on thumbnail display screen. No still icon will appear for card.
PLAYING BACK FROM DISC NAVIGATION SCREEN Press the A button. Press the DISC NAVIGATION button. Use the joystick to select the desired scene. Playback will start from the selected scene. Note The selected scene will be framed: This is called Tilting the joystick to left or right will move the cursor to the preceding or following scene.
SELECTING MULTIPLE SCENES Press the DISC NAVIGATION button. Repeat steps 2 and 3 to randomly select multiple scenes. Use the joystick to select the desired scene. To cancel a selected scene, select the scene to be canceled, and then press the SELECT button. To cancel all selected scenes, press the C button.
FUNCTIONS AVAILABLE WITH DISC NAVIGATION The Disc Navigation mode will allow a variety of further operations. Reference Available function Disc or card used Contents page Deletion of scenes You can delete unnecessary scenes. Editing of scenes You can attach fade and skip to a scene, 113 - 117 combine scenes, or divide one scene.
UNDERSTANDING FLOW OF DISC NAVIGATION MENU Press the MENU button on the Disc Navigation screen: The menu screens for Disc Navigation and menu screens for disc and card will appear. See pages 87-89 and 106 for how to interpret the screen. Refer to pages indicated for details of settings.
Scene DELETING SCENES (DELETE) You may want to delete unwanted scenes. Scenes on DVD-R disc cannot be deleted, and menu item “Delete” will not appear with DVD-R disc. Press the C button to Press the DISC NAVIGATION button. De l e t e Sc en e 0 05 / 0 1 3 quit.
Editing using submenu Press the MENU button before pressing the A button in step 5 (See page 111): The submenu will appear. Ed i t Se l e c t Go To E x i t De l e t e S t a r t –...
CHANGING IMAGES FOR THUMBNAILS (EDIT - THUMBNAIL) Normally, the first image of the recorded scene is displayed as a thumbnail: You can choose another image of the scene for thumbnail. If you set a vivid image to thumbnail, you can know what you recorded from a glance at the Disc Navigation screen.
PLAYING BACK BY SKIPPING SCENES (EDIT - SKIP) You can specify “Skip” for scenes you do not want to play back: The selected scenes will be skipped. Press the C button to quit. Press the DISC NAVIGATION button. Select the scene to be skipped. A skip icon “...
DIRECTING SCENES EFFECTIVELY (EDIT - FADE) You can add fading to the beginning and/or end of scene. There are three types of special effects: Fade Out Fade Out Fade Out Fade In Fade In Fade In White: Wipe: B/W: Fades in from white screen Fades in from black screen to Fades in from Black and White Fades out to white screen...
COMBINING MULTIPLE SCENES (EDIT - COMBINE) If you have recorded numerous short scenes, combining them will be facilitated by the use of Disc Navigation. Be sure to select consecutive multiple scenes. Combining scenes is possible only when “Category: All” is specified. (P.138) Stills cannot be combined. Press the C button to quit.
DIVIDING MOVIES (EDIT - DIVIDE) You can divide a scene into two parts. To delete unnecessary portion of scene, first divide the scene, and then delete the unnecessary portion. Press the DISC NAVIGATION button. Note • If you press the MENU button before pressing the button in step 5, the submenu screen will appear.
COPYING STILLS ON DVD-RAM DISC TO CARD (COPY) Set the power switch to “O VIDEO” or Note “N PHOTO“. • No movie can be copied. • If you press the MENU button before pressing the button in step 6, the submenu screen will appear. (P.112) Press the DISC NAVIGATION button.
LOCKING SCENES ON CARD (LOCK) You can lock each photo recorded on card so that it will not be deleted or edited by mistake. Set the power switch to “P PHOTO”. To unlock the scene: Select the locked scene, and then use the same Press the DISC NAVIGATION button.
DESIGNATING SCENES TO BE PRINTED (DPOF) You can use DPOF to set print information, including selection of the scenes to be printed, so that you will be able to use it on a system conforming to DPOF. Note DPOF stands for digital print order format. DPOF is used to ask a print lab to print recorded stills. Set the power switch to “P PHOTO”.
SELECTING SCENES USING MENU SCREEN (SELECT) You can use this “Select” function to select consecutive scenes at one time. This function is useful when there are numerous scenes. Choose “Start → Press the DISC NAVIGATION button. Current”, “Current → Sc ene De l e t e Select the first scene to be selected.
DISPLAYING INFORMATION USING MENU SCREEN (DETAIL) You can display various information for a scene: the recording mode, recording date/time and length, special effects and movie quality mode. Press the DISC NAVIGATION button. If you have selected multiple scenes, the information shown below will appear. Pressing the C button will restore the Select the scene whose information you wish to know.
Program WHAT IS “PROGRAM”? Program refers to an assembly of scenes recorded on the same date regardless of whether they are movie or still. Scene No. 1 Scene No. 2 Scene No. 3 Scene No. 4 Scene No. 5 Scene No. 6 9:00AM Movie Movie...
PLAYING BACK PROGRAM (PLAY) You can play back only the selected program. Press the DISC NAVIGATION button. Select the program to be played back, and then press the A button. Press the MENU button. Playback will start from the first scene of the Choose “Play”...
Page 125
After entering the title, Characters available for entering T I T L E a t a P a r k choose “Enter” and then title 1 2 3 4 5 6 7 8 9 0 SPACE press the A button. a b c d e f g h i j k l m n o p q r s t u v w x y z You can use the joystick to select characters from...
Play List WHAT IS “PLAY LIST”? You can create a play list on this DVD video camera/recorder by gathering your favorites from the recorded scenes. Since the play list is not created by copying data, you will consume little of the disc capacity by making a play list.
SWITCHING TO DISPLAY OF EACH PLAY LIST (SWITCH) Select the desired one of multiple play lists: The Disc Navigation screen of the selected play list will appear. Press the DISC NAVIGATION button. Use the “Switch Playlist” 0 1 8 / 3 0 / 2004 1 2 : . . 0 01 / 008 screen to select the play Press the MENU button.
ADDING SCENES TO PLAY LIST (EDITING PLAY LIST) Press the DISC NAVIGATION button. Tilt the joystick down to move the cursor to the lower row, and tilt it to left or right to select the Press the MENU button. point where the scene is to be inserted. Choose “Edit”...
DELETING SCENES FROM PLAY LIST (EDITING PLAY LIST) Press the A button. Press the DISC NAVIGATION button. Ed i t P l a yL i s t A l l P r o g r ams 0 0 4 / 0 1 4 Display the editing Repeat steps 3 and 4 to Ed i t P l a yL i s t...
DELETING SCENES USING SUBMENU FOR EDITING (EDITING PLAY LIST) You can delete scenes from play list on the editing screen. Press the DISC NAVIGATION button. Choose “Delete” on the Ed i t “Edit” menu screen, and A l l P r o g r ams 0 0 1 / 0 1 4 Ex i t then press the A...
ARRANGING ORDER OF SCENES (MOVE) You can move scenes only when “Category: All” is specified. Press the DISC NAVIGATION button. The screen for verifying Move Scene move will appear: Press the MENU button. Choose “YES”, and then Move sc e n e s? press the A button.
CHANGING TITLE OF PLAY LIST (TITLE) The play lists have serial numbers in the order you have created them, along with the created dates/ times: You can change this title at any time. Press the DISC NAVIGATION button. The screen for verifying T I T L E a t a Pa r k exit will appear: Choose Press the MENU button.
Go To From the Disc Navigation screen, you can jump to the first scene or last scene. TOP (END) Press the DISC NAVIGATION button. Press the MENU button. Choose “Top” or “End” Go T o on the “Go To” menu screen, and then press the A button.
Disc or Card Management VERIFYING REMAINING FREE SPACE ON DISC OR CARD (CAPACITY) You can find out how long you will be able to record on one side of disc or on card. Press the C button to quit. Press the DISC NAVIGATION button. Press the MENU button.
INITIALIZING DVD-RAM DISC OR CARD (FORMAT DISC. FORMAT CARD) • Be sure to use the AC adapter/charger to power the DVD video camera/ recorder for initialization. If the DVD video camera/recorder is turned off Before You Begin during initialization and the initialization is interrupted, incorrect initialization will result and the incorrectly initialized disc will be unusable.
UPDATING CONTROL INFORMATION OF DVD-RAM DISC (UPDATE CONTROL INFO.) Disc Navigation in this DVD video camera/recorder handles information on scenes, such as thumbnail, skip, fade, in a particular manner. If you use another device to edit a disc recorded on this DVD video camera/recorder, and then use the data again with Disc Navigation in this DVD video camera/recorder, the Disc Navigation may not appear normally.
FINALIZING DVD-R DISC (FINALIZE DISC) • Be sure to use the AC adapter/charger to power the DVD video camera/ recorder when finalizing a DVD-R disc. If the DVD video camera/recorder Before You Begin is turned off during finalization and the finalization is interrupted, incorrect finalization will result, and at worst, the disc may be damaged.
Others DISPLAYING MOVIES OR STILLS INDEPENDENTLY (CATEGORY) Scenes recorded on this DVD video camera/recorder will be displayed in the order of recording regardless of whether they are movies or stills. You can use the Disc Navigation screen to switch this display to stills only or movies only.
SLIDE SHOW (CONTINUOUS PLAYBACK OF STILLS) If you play back stills recorded on a card, the DVD video camera/recorder will enter the playback pause status after each still is played back. Setting Slide Show allows you to continuously play back stills. Press the DISC NAVIGATION button.
Connecting to PC THE FOLLOWING ARE AVAILABLE WHEN CONNECTING TO PC Use the provided PC connection cable to connect this DVD video camera/recorder to your PC in which the software on the CD-ROM provided or generally available software is installed: The videos and photos recorded on the DVD video camera/recorder can be used on the PC.
Page 141
Using PC to edit images on DVD-RAM disc recorded on this DVD video camera/recorder: Original disc Written disc Application used DVD-RAM disc recorded on Original DVD-RAM disc or DVD-MovieAlbumSE** this DVD video camera/ another DVD-RAM disc recorder Using PC to edit images on DVD-RAM disc recorded on this DVD video camera/recorder and create a DVD video (DVD-R disc) (see page 152): Original disc Written disc...
Contents on Provided CD-ROM The CD-ROM supplied with the DVD video camera/recorder contains the following folders: To refer to the contents of CD-ROM, set the CD-ROM in the CD-ROM drive of PC, right-click the CD-ROM icon and choose “Open”. Contains the DVD-MovieAlbumSE (see page 148 for installation). You can use DVD-MovieAlbumSE to edit the images recorded on DVD-RAM disc and create a 3D title.
“Document” folder. • After installing DVD-MovieAlbumSE, open “Programs”or “All Programs” from the To read the above manual, a Web browser (Internet Windows “Start” menu, choose “Hitachi Explorer, Netscape Communicator, etc.) must be DVDCAM” and “DVD-MovieAlbumSE”, and set up in your PC.
*InstantWrite provided with the DZ-WINPC1, DZ-WINPC2 or DZ-WINPC2B PC kit for the Hitachi DZ-MV100A DVD video camera/recorder, or with the DZ-WINPC3 PC editing kit for the Hitachi DZ- MV200A, DZ-MV230A or DZ-MV270A DVD video camera/recorder. If the UDF driver has been installed, uninstall it and then install the UDF driver on the provided CD- ROM.
INSTALLING USB DRIVER With Windows XP Click “USB Driver Installation” on the installer The message on Windows logo test will appear: screen. Carefully read it and then click “Continue Anyway”. The USB driver installer screen will appear: Click “USB Driver Installation”. Installation will start.
INSTALLING UDF DRIVER (DVD-RAM DRIVER) The UDF driver must be installed before using the disc in DVD video camera/recorder on PC. Click “UDF Driver (DVD-RAM Driver) Carefully read the License Agreement: If you Installation” on the installer screen. accept it, click “Yes”. The installer screen can be displayed using the The contents of agreement displayed on actual procedure in “DISPLAYING INSTALLER...
Page 147
® If you do not wish to change the folder name, If your PC uses Windows XP/98 Second click “Next”. Edition/Me, a message that prompts you to restart will appear: Click “Finish” and then restart the PC. Installing the UDF driver is now complete. ®...
INSTALLING DVD-MovieAlbumSE Software “DVD-MovieAlbumSE” is used to edit videos that conform to the DVD video recording (DVD- VR) format, and photos recorded on DVD-RAM disc. Click “DVD-MovieAlbumSE Installation” on If you do not wish to change the folder in which the installer screen.
Page 149
Check the displayed contents, and then click “Next”. Installation will start. Proceed with the installation, following the instructions on screen. Click A message verifying whether a shortcut icon is to be created on desktop will appear: If you want to create one, click “Yes”. If not, choose “No”.
INSTALLING MyDVD Software “MyDVD” is used to write the images edited on DVD-MovieAlbumSE to DVD-R disc. Click “MyDVD Installation” on the installer If you do not wish to change the folder in which screen. MyDVD is installed, click “Next”. The installer screen can be displayed using the procedure described in “DISPLAYING INSTALLER SCREEN”...
Page 151
Click “Finish” to restart the PC. Contact the following for information on MyDVD: Installing MyDVD is now complete. U.S. Phone: 1-877-383-1124 http://support.sonic.com/login/ default.asp (You will need to perform customer registration.) Europe (London) Phone: 44-20-7437-1100 http://support.sonic.com/login/ default.asp (You will need to perform customer registration.) Click Sonic Solutions Corporation, which developed...
Creating DVD Video on PC from DVD-RAM Disc Recorded on DVD Video Camera/Recorder Using DVD-MovieAlbumSE and MyDVD, you can create a DVD video (DVD-R disc) from the images recorded on this DVD video camera/recorder, following the procedure below: Insert a recorded DVD-RAM disc into the DVD Note video camera/recorder, and connect the DVD •...
Page 153
MyDVD will automatically start. After a few Click the Burn button: Writing to DVD-R disc moments, the exported scene will be will start. When writing is complete, a DVD automatically registered on the MyDVD video disc will be created. editing screen: Then the disc cover of this DVD video camera/ recorder will open automatically.
Open “System” on Control Panel, and then Ltd.DZ3298.inf choose the “Device Manager” tab. C:\WINDOWS\SYSTEM\IOSUBSYS\dzmvpd r.pdr Delete HITACHI DVD-RAM DZ-MV5 in “CD- C:\WINDOWS\SYSTEM32\DRIVERS\DZMVU ROM”. MSS.sys No extension may appear depending on the setting on If the file does not exist, proceed with the next step: ®...
Also delete the oem*.PNF files with the same found, proceed with the next step: numbers as those of the files deleted in step 8. Delete Hitachi DVDCAM DVD Mode USB HS Disconnect the DVD video camera/recorder Interface in “USB (Universal Serial Bus) from PC, and then restart the PC.
JPEG files in 100HPNX1 folder to the hard disk of PC. • Ordinary data on PC can usually be written to DVD-RAM disc in this DVD video camera/recorder, but Hitachi does not guaranteed the operation. • If the PC is started from suspend (see “Terminology” on...
• When using camera accessories, be sure to read the instruction manuals for each accessory. * When attaching the wide or tele-conversion lens to this DVD video camera/recorder, be sure to remove the lens hood at the end of the lens (see P. 57). ** Unusable on DZ-MV550A. POWER SUPPLY Battery (DZ-BP14SW)
Cleaning Be sure to set the power switch to “POWER OFF” before cleaning this DVD video camera/recorder. Cleaning LCD screen and camera Do not use benzene or thinner to lens clean DVD video camera/recorder case Use dry, soft cloth to wipe dirt off. When cleaning the LCD screen, be careful not to use force, scratch The coating of case could peel off or the case could it, or subject it to impact: Doing such could cause...
Changing Setting of Demonstration This DVD video camera/recorder has versatile functions, including special effects. Referring to the procedure on page 43, connect the DVD video camera/recorder, AC adapter/charger and power cable to power the DVD video camera/recorder from AC outlet. Press the MENU button.
Terminology DISC-PROTECT: This disables writing to disc (protects disc from writing) so that images recorded on DVD-RAM disc cannot be accidentally deleted and the disc cannot be initialized. DVD PLAYER: This device can play back video and audio signals recorded on DVD-Video and DVD-R discs using the DVD video format.
Page 161
FINALIZE: This process makes a DVD-R disc recorded on this DVD video camera/recorder playable on a DVD player, etc. that conforms to 8 cm DVD-R: No further recording can be made on a finalized DVD-R disc. HOWLING: This phenomenon occurs as follows: When the DVD video camera/recorder is connected to a device, such as TV, the audio input to the microphone of DVD video camera/recorder is amplified and output from the speakers of TV, and the signal is again input to the microphone: This is repeated to form an endless loop of audio signal, and the signal is amplified up to the audio output amplitude limit of the...
SD MEMORY CARD: This is a standard of memory card developed in 1999. The card is 32 mm long x 24 mm wide x 2.1 mm thick, and has 9 pins. Since the SD memory card was developed based on MultiMediaCard (MMC), MMC can be inserted into SD memory card slot and used.
No DVD Video Camera/Recorder Operation - Check the Following: Check 1 No movie can be recorded Skip or search playback does Check 3 not work well Movie can be recorded only on DVD-RAM or DVD-R If the temperature inside the DVD video camera/ disc.
Page 164
No DVD video camera/recorder No image appears on the LCD Check 5 Check 7 operation screen or in the viewfinder • Is a fully charged battery attached? Is DVD video camera/recorder connected to PC Is the DVD video camera/recorder powered from AC using PC connection cable? outlet? Unplug the PC connection cable.
Trouble Messages A message may appear while you are operating the DVD video camera/recorder. If a message appears, refer to the following table and take appropriate corrective action. Messages are arranged in alphabetical order. Reference Message Cause & Troubleshooting page (1) Data error in a part of It is possible that the system cannot normally complete writing of file image file.
Page 166
Reference Message Cause & Troubleshooting page • (1) Error has occurred. Error has occurred. Try to restart the DVD video camera/recorder Please restart. using the following methods: (1) Turn power off, remove the battery or AC adapter/charger and (2) Error has occurred. reattach it, and then turn power on again.
Page 167
Reference Message Cause & Troubleshooting page • Card error. The card terminals may be dirty: Wipe off dirt, and try the card again, or use another card. • Data other than still image may be included: Use another card. Card error has occurred. Card error could have occurred during editing of scenes.
Page 168
Reference Message Cause & Troubleshooting page Disc error has occurred. The disc may be dirty. Formatting is not Remove the disc and wipe off fingerprints, dust, etc. before reusing complete. it, or use another disc. 82, 135 This message may also appear if you insert a disc for which formatting was interrupted midway.
Page 169
Reference Message Cause & Troubleshooting page DVD-R Disc, Video With DVD-R disc, the movie quality mode once used for recording mode cannot be cannot be changed. changed. END OF DISC The disc is full. You cannot record on this disc anymore. Prepare another disc or delete unnecessary movie scenes from this disc.
Page 170
Reference Message Cause & Troubleshooting page Scenes over limit. The number of scenes entered in play list has reached the limit that Cannot add scene. can be entered. 126, 130 Delete several scenes. Scenes over limit. The number of entered scenes has reached the limit that can be Cannot divide scene.
Page 171
• This message may also appear when dirt adheres to disc. If this message appears when a recorded disc is recognized immediately after it is inserted, do not repair the disc; remove it and then use a soft, dry cloth to clean off the dirt before using it. •...
Troubleshooting Check to see the following before asking for a repair. If the suggested solution still cannot restore the DVD video camera/recorder to normal, do not attempt to repair it yourself, but consult your dealer. Power supplies Reference Symptom Cause and Correction page Battery cannot be Is the ambient temperature too low or too high?
Page 173
During recording Reference Symptom Cause and Correction page Pressing the REC button Is input image copy-guarded? 28, 84, 134, will not start recording. Is the disc write-protected or the card locked? Recording starts but Is disc scratched or does dirt or fingerprint adhere to it? stops immediately.
Page 174
During playback Reference Symptom Cause and Correction page Recognition of disc is not Is disc dirty? complete Use soft, dry cloth to clean it. Pressing the playback Has the image been recorded by devices other than this DVD video button will not start camera/recorder? playback.
Page 175
Reference Symptom Cause and Correction page Photos on card cannot be This DVD video camera/recorder can play back image data played back. recorded on SD memory card in other digital cameras conforming to the DCF (Design rule for Camera File system) standard. The range of image data normally playable on this DVD video camera/ recorder is that with pixels from 80 horizontal x 60 vertical to 4000 horizontal x 3000 vertical.
Page 176
When the DVD video camera/recorder is connected to PC: Reference Symptom Cause and Correction page No drive icon appears on The DVD video camera/recorder is not turned on. Check the power supply. Driver is not properly recognized. Turn PC off and on again. If the drive icon still does not appear, use “Refresh driver”...
Page 177
Reference Symptom Cause and Correction page Video written to hard disk DVD-MovieAlbumSE cannot edit DVD-VR data stored on hard disk of PC cannot be edited of PC: Copy the data to another DVD-RAM disc and then edit it. on DVD-MovieAlbum copy tool.
Page 178
Reference Symptom Cause and Correction page Executing “Export” on Do not choose “Simple Export”: If you do, reading will stop midway. DVD-MovieAlbumSE will interrupt reading midway. • When executing “Export” If stills are included in the range of “export”, it may take more time on DVD-MovieAlbumSE, because data must be re-encoded and read.
Page 179
Miscellaneous Reference Symptom Cause and Correction page Power does not come on, Execute system reset (press the RESET button). or no operation occurs by Has the DVD video camera/recorder been subjected to impact? pressing button. The DVD video camera/recorder could be damaged. Consult your dealer.
Page 180
Reference Symptom Cause and Correction page Disc cover cannot be Is disc correctly inserted? closed. Was disc inserted from wrong direction? Remove the disc and then reinsert it. Is disc inserted in wrong orientation? Remove the disc, and then reinsert it. Connect a fully charged battery or AC adapter/charger, and then 39, 43 turn the DVD video camera/recorder on.
System Reset If the DVD video camera/recorder does not operate normally, perform “System Reset”: The DVD video camera/recorder may recover to normal. “System Reset” will reset all settings to factory defaults. The date and time will also be reset: Set the date and time again before using the DVD video camera/recorder. Set the power switch to “POWER OFF”...
Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: HITACHI AMERICA, LTD. HOME ELECTRONICS DIVISION 900 Hitachi Way Chula Vista, CA 91914-3556 U.S.A...
Article 5 Termination of Agreement If you fail to comply with the terms of this Agreement, Hitachi, Ltd., Matsushita Electric Industrial Co., Ltd. and Sonic Solutions reserve the right to terminate the Agreement. In such a case, you will be obliged to discard all copies of This Software and its components.