Yaesu Mark-V FT-1000MP Operating Manual page 104

Menu Selection and Settings
5-2 CW nor
CW Normal Filters - Selects the CW filters used
when the front-panel [ NOR ] switch is selected (while
in the CW mode).
8.2 - Sets the 2nd IF to the optional 2.0 kHz filter,
and the 3rd IF to the 2.4 kHz filter.
455 - Sets the 2nd IF to the 2.4 kHz filter, and the
3rd IF to the optional 2.0 kHz filter.
8.2-455 - Sets the 2nd IF and 3rd IF filters to 2.0
kHz filter options.
Note: If you have not installed the optional 2.0 kHz
filters (or if you disable the optional 2.0 kHz filters by
menu selection 5-1 and/or 5-5), the received signal will
pass through the standard 2.4 kHz filter.
5-3 8.2-250
2nd IF 250 Hz Filter - Enables/disables the optional
250 Hz IF filter (Yaesu P/N YF-114CN).
5-4 dAtAnAr2
DATA Narrow 2 Filters - Selects the filters used
when the front-panel [ NAR2 ] switch is selected (while
in the DATA mode).
8.2 - Sets the 2nd IF to the optional 250 Hz filter,
and the 3rd IF to the optional 500 Hz filter.
455 - Sets the 2nd IF to the 500 Hz filter, and the
3rd IF to the optional 250 Hz filter.
8.2-455 - Set the 2nd IF and 3rd IF filters to the 250
Hz filter options.
Note (1): If you have not installed the optional 2nd
IF 500 Hz filter (or if you disable the filter by menu se-
lections 5-3 ), the received signal will pass through the
supplied 500 Hz filter.
Note (2): If you have not installed the optional 3rd
IF 500 Hz filter (or if you disable the filter by menu se-
lections 5-6 ), the received signal will pass through the
supplied 2.4 kHz filter.
Note (3): If you have not installed the optional 3rd
IF 250 Hz filter (or if you disable the filter by menu se-
lections 5-7 ), the received signal will pass through the
supplied 2.4 kHz (or optional 500 Hz) filter.
5-5 455-2.0
3rd IF 2.0 kHz Filter - Enables/disables the op-
tional 2.0 kHz IF filter (Yaesu P/N YF-110SN).
5-6 455-500
3rd IF 500 Hz Filter - Enables/disables the optional
500 Hz IF filter (Collins YF-115C).
page 102
5-7 455-250
3rd IF 250 Hz Filter - Enables/disables the optional
250 Hz IF filter (Yaesu P/N YF-110CN).
5-8 Sub-FiL
SUB VFO Filter - Enables/disables optional SUB
VFO-B 2nd IF 500-Hz CW filter (Collins YF-115C).
5-9 t-FiL
TX EDSP Filter - Selects either a 6.0-kHz or 2.4-
kHz digital bandpass filter for early-stage transmit au-
dio tailoring.
6-0 rttY-SHF
RTTY Frequency Shift - Selects 170, 425, or 850
Hz standard frequency shift for FSK RTTY operation.
Important Note! - If changing RTTY shift to other
than 170 Hz, be sure to re-calibrate the tuning meter
as outlined on page 85. The calibration routine is simple,
and ensures your center tuning indication matches the
tone pair.
6-1 rttY-PoL
RTTY Polarity - Selects normal or reverse Mark/
Space polarity for RTTY operation. Normal operation
utilizes a 2125-Hz mark frequency, while reverse uses
2295 Hz. See the table on page 17 for a list of stan-
dard tone pairs.
6-2 rttY-ton
RTTY Tone - Selects high or low mark tone for
RTTY operation. See the table on page 17 for a com-
parison of high/low tone pairs.
6-3 rtY-FdSP
RTTY Frequency Display - Selects the type of dis-
play offset that appears during RTTY operation.
Offset - Displays the RTTY BFO offset.
Carrier - Displays the actual carrier frequency.
6-4 PAc-FdSP
Packet Frequency Display Offset - You can off-
set the frequency readout to display the center fre-
quency between the two transmitted carriers (tone
pairs). Rotate the MAIN VFO-A knob to adjust the dis-
play offset, or else set to 0.00 to display the actual car-
rier frequency. See menu selection 6-5 below for tone
pair selection.
MARK-V FT-1000MP Operating Manual