Download  Print this page

Recessed And Closet Installation Instructions - KitchenAid Gaz dryer 3395322 Installation Instructions

Hide thumbs
   

Advertisement

Recessed and
closet installation
instructions
/
6.
Fire/Health
Hazard
Exhaust
the dryer to the outside to prevent
exposure
to substances
in the gas fuels and
combustion
by-products
which may be
harmful to your health.
Failure to do so may result in a fire or health
hazard.
2. 3.
The following installation spacings and door air
openings for the dryer are possible when installed
and exhausted
as noted. (Spacing as indicated is
in inches and is minimum allowable.
For ease of
installation and service, additional spacing should
be considered.)
Numbers
correspond
to steps.
17 .
Now stand the dryer up.
I-1 2.1
Use a brush and liquid deterqent to
I
e-o"*
recessed
front view
-
test all external gas connections for
leaks. Bubbles around connections will indicate a
leak. If a leak appears, shut off gas valve controls
and adjust connections.
Then check connections
again.
I I
M
I
To exhaust
the dryer,
see "Exhaust
requirements."
Connect
exhaust duct to exhaust
hood. Use duct tape to
seal all joints in exhaust
duct. Use caulking
compound to seal exterior
wall opening around
exhaust hood.
1
1
@-I
Move the dryer close to its final location.
,
To make sure the dryer is level, take a
carpenter's
level and place it on the top of
the dryer, first side to side; then front to back. If the
dryer is not level, adjust the legs of the dryer up or
down.
da
Plug the power supply
cord into the grounded
outlet.
TO PREVENT LARGE AMOUNTS
OF LINT AND
MOISTURE
FROM ACCUMULATING,
TO
MAINTAIN
DRYING EFFICIENCY
AND TO
PREVENT EXPOSURE
TO POSSIBLE
HEALTH
HAZARDS,
THIS MACHINE MUST BE
EXHAUSTED
OUTDOORS.
+ Additional
clearances
for wall, door and floor moldings may be
Remove the red cap from the gas pipe.
Move the dryer into its final position.
required.
-- Opening is minimum for close1 door. Louvered
door with
equivalent
air openings is acceptable.
-
Additional
space is needed when external exhaust elbow is used
I
I
P-l I
Connect gas supply to dryer. Use pipe-
.
joint compound resistant to the action of
LP gas for gas connections.
If flexible
metal tubing is used, be certain there are no kinks.
Companion appliance spacings should be
considered.
Detailed space requirements
can be found on the
label located on the back panel of dryer.
NOTE:
No other fuel-burning
appliance
may be
installed
in the same closet.
Part No.
3395322
Rev. A
Turn the dryer
on to remove
air from the gas
supply line. Using a full heat
cycle (not the air cycle), let
the dryer run for at least five
minutes.
If the burner does
not ignite and you can feel
no heat inside the dryer, shut
off the dryer for five minutes.
timer c~ntrct knob
Check that the gas supply line
shutoff valve is in "ON" position.
Repeat the five-
minute test.
Open the shutoff valve in the gas
supply line.
Check to make sure you have all the
tools you started with in Step A,
To get the most efficient
use from
your new dryer, read your
KitchenAid
Use and Care Guide.
Keep Installation
Instructions
and
Guide close to dryer for easy
reference.
Fire Hazard
Do Not use an open flame to test for leaks
from gas connections.
Checking
for leaks with a flame may result in
a fire or explosion.
Panel C

Advertisement

Table of Contents
loading

  Related Manuals for KitchenAid Gaz dryer 3395322

This manual is also suitable for:

3395322