ADJ Mega Bar 50 RGB RC User Instructions page 6

Mega Bar 50RGB RC
The ADJ LED RC infrared remote has many differnet functions and
gives you complete control of your Mega Bar 50RGB RC. To control
the your desired fixture you must aim the controller at the front of the
fixture and be no more the 30 feet away. To use the ADJ LED RC you
must first activate the fixtures infrared receiver, to activate the receiv-
er please see the instructions on page 9.
BLACkOUT - Pressing this button will blackout the fixture.
AUTO RUN - This button will run an automatic program. You can
control the speed of the Auto Run by pressing the SPEED button first
and then pressing the "+" and "-" buttons.
PROGRAM SELECTION - This button will let you access the units
built-in programs. Pressing this button and then press the "+" or "-"
to navigate through the built-in programs.
FLASH - This button will activate the strobe effect. You can control
the flash rate by pressing the "+" and "-" buttons. Press this button
again to exit strobe mode.
SPEED - Press this button and use the "+" & "-" buttons to adjust the
speed of the Auto run.
DMX MODE - This button will let you select which DMX mode you
want to use. Some fixtures will come with different DMX channel
modes. This button will switch between the different modes. Please
see pages 12-15 for DMX modes, values, and traits.
SOUND ACTIVE - Press this button to activate sound active mode.
Use the "+" & "-" buttons to adjust the sound sensitivity.
SLAVE - This designates the fixture as a slave fixture in a master/
slave configuration.
SET ADDRESS - Press this button to set the DMX address. Press
this button first, then press the numbers to set the address.
Example: DMX Address 1 Press "S001"
DMX Address 245 Press "S245"
R G B - Press either one of these buttons and the press the "+" or "-"
to adjust the brightness.
"+" and "-" - Use these buttons to adjust the flash rate, speed of the
American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 11
©
ADJ LED RC Operation Mega Bar 50RGB RC
Auto Run, sound sensitivity, and program selection.
DMX Control:
Operating through an Elation® DMX controller gives the user the
freedom to create their own programs tailored to their own individual
needs. Follow the directions below to set your DMX Mode and ad-
dress.
1. Before connecting to an Elation® DMX controller, your fixture has
different DMX channel modes, please select your desired mode by
pressing the DMX Mode button, then using the "+" or "-" buttons
to scroll through the DMX Channel Modes. Set the mode before
you address the fixture. See the bottom of this page for the DMX
modes.
2. After you have selected your mode, set the DMX address for the
fixture by pressing the "S" button. When the "S" button is pressed
the LED's will flash 2-3 times and all the red LED's will light. Use
the number buttons to press in your desired address. See "SET
ADDRESS" on page 10 for examples.
Note: When seeting the DMX address each time a number is pressed
a LED color will glow, when you have set the DMX address correctly
all LED's will flash 2-3 times.
3. Now you may connect the fixture via the XLR connections to any
standard Elation® DMX controller. Please see pages 13-16 to for a
detailed descriptions of the DMX modes, values, and traits.
• If all of the Red LED's glow you are in DMX Mode 1: 1 DMX
Channels
• If all of the Green LED's glow you are in DMX Mode 2: 2 DMX
Channels
• If all of the Blue LED's glow you are in DMX Mode 3: 3 DMX
Channels
• If Red LED's & Green LED's glow you are in DMX Mode 4: 4
DMX Channels
• If Red LED's & Blue LED's glow you are in DMX Mode 5: 5 DMX
Channels
• If Green LED's & Blue LED's glow you are in DMX Mode 6: 6
DMX Channels
• If all of the LED's glow you are in DMX Mode 7: 7 DMX Channels
American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 12
©
ADJ LED RC Operation