How To Configure The External Networks (Management Lan/ Maintenance Lan/Production Lan); Ip Addresses Used In The Primequest 2000 Series Server; Table 1.2 Ip Addresses For The Primequest 2000 Series Server (Ip Addresses Set From The Mmb) - Fujitsu PRIMEQUEST 2000 Series Administration Manual

CHAPTER 1 Network Environment Setup and Tool Installation

1.2 How to Configure the External Networks (Management LAN/ Maintenance LAN/Production LAN)

1.2 How to Configure the External Networks (Management
LAN/ Maintenance LAN/Production LAN)
The PRIMEQUEST 2000 series server must be connected to the following three types of external networks.
The respective external networks are dedicated to security and load distribution. (See
network configuration.)
- Management LAN
- Maintenance LAN
- Production LAN
Note
Be sure to connect management LAN, production LAN and maintenance LAN to different subnet each other
This section describes the IP addresses for the PRIMEQUEST 2000 series server.

1.2.1 IP addresses used in the PRIMEQUEST 2000 series server

Each of the SB, IOU, and MMB units in the PRIMEQUEST 2000 series server has network interfaces. Each
port of these network interfaces must be assigned an IP address.
To the ports, assign IP addresses appropriate to the external network environment of the PRIMEQUEST
2000 series server.
The following describes the IP addresses assigned to the ports.

TABLE 1.2 IP addresses for the PRIMEQUEST 2000 series server (IP addresses set from the MMB)

IP addresses that are set from the MMB.
(set from the operating system in a partition)
The IP addresses in
from the MMB)
to an SB or an external network port of the MMB through the switching hub on the MMB. The MMB firmware
uses the IP addresses.
The standard configuration has one MMB. For a dual MMB configuration, which has two MMBs, assign a
common virtual IP address to both MMBs. In addition to the virtual IP address, assign one physical IP
address to each MMB.
TABLE 1.2 IP addresses for the PRIMEQUEST 2000 series server (IP addresses set from the MMB)
Name
- Management LAN IP address: MMB Virtual/Physical IP address
This IP address is used for communication when the MMB is connected to the management LAN. The
physical IP address is assigned to the NIC of the user port of each MMB, and the virtual IP address is
assigned commonly to the duplicated MMBs. The virtual IP address is used for access from PC etc. on the
management LAN. The virtual IP is inherited by an active MMB.
Virtual IP MMB
Address (common)
(*1)
MMB#0 IP MMB#0 (*1)
Address
MMB#1 IP MMB#1 (*1)
Address
- Maintenance LAN IP address: Maintenance IP address
This IP address is used for communication when the MMB is connected to the maintenance LAN.
Maintenance MMB
TABLE 1.2 IP addresses for the PRIMEQUEST 2000 series server (IP addresses set
are assigned to the NICs (network interface controllers) on the MMBs. Each NIC is connected
NIC Type
Virtual IP
address
Physical
IP address
Physical
IP address
Physical IP
TABLE 1.3 IP addresses for the PRIMEQUEST 2000 series server
lists the IP addresses that are set from the operating system.
IP address
setting
method
Set it from The PC connected to the management LAN
the MMB uses this IP address to communicate (via the
CLI or MMB Web, telnet, etc.) with the (active) MMB. The
Web-UI. PC user need not be aware of which MMB is
active, MMB#0 or MMB#1.
Set it from The PC connected to the management LAN
the MMB uses this IP address to communicate with
CLI or MMB MMB#0. (*2)
Web-UI.
Set it from The PC connected to the management LAN
the MMB uses this IP address to communicate with
CLI or MMB MMB#1. (*2)
Web-UI.
Set it from This IP address is used for communication
3
FIGURE 1.1 External
Description
C122-E175-02EN
lists the