Yamaha MOTIF ES Owner's Manual page 217

[SF5] OTHER
PB (Pitch Bend) Upper,
PB (Pitch Bend) Lower
PB (Pitch Bend) Range
VelSensDpt
(Velocity Sensitivity Depth)
VelSensOfst
(Velocity Sensitivity Offset)
[F2] OUTPUT
[SF1] VOL/PAN (Volume/Pan)
Volume
Pan
VoiceELPan (Voice Element Pan)
[SF2] EF SEND (Effect Send)
RevSend (Reverb Send)
ChoSend (Chorus Send)
Dry Level
These two parameters are available for Parts 1 - 4 to which the internal Normal Voices are assigned. These
determine the pitch change range (in semitones) of the Pitch Bend wheel for the Part's Voice. For example, a Lower
setting of -12 would result in the pitch being lowered up to a maximum of one octave (12 semitones) when the Pitch
Bend wheel is moved downwards. Similarly, setting the Upper parameter to +12 would result in a maximum pitch
rise of one octave when the wheel is moved upwards.
Settings: -48 ~0 ~+24
This parameter is available for Parts 1 - 4 to which the internal Drum Voices are assigned and Plug-in Parts 1 - 3. This
determines the pitch change range (in semitones) of the Pitch Bend wheel. Unlike the Pitch Bend setting for Parts 1
- 4 to which the internal Normal Voices are assigned described above, the Upper and Lower ranges of the Drum
Voice Parts and Plug-in Parts cannot be set independently.
Settings: -24 ~ 0 ~ +24
Determines the degree to which the resulting volume of
the tone generator responds to your playing strength.
The higher the value, the more the volume changes in
response to your playing strength (as shown at right).
Settings: 0 ~ 127
Determines the amount by which played velocities are adjusted for the actual resulting velocity effect. This lets you
raise or lower all velocities by the same amount — allowing you to automatically compensate for playing too strongly
or too softly.
Settings: 0 ~ 127
When Depth (above) = 64 and Offset = 32
127
Actual resulting
velocity (affecting
the tone generator)
0 64
Determines the volume for each Part, giving you detailed control over the level balance among the Parts.
Settings: 0~127
Determines the stereo pan position for each Part.
Settings: L63 (far left) ~ C (center) ~ R63 (far right)
Determines whether the individual pan settings for each Voice (made via [VOICE]
[F4] AMP [SF1] LVL/PAN Pan) are applied or not. When this is set to "off," the basic pan position for the
selected Part is set to center.
Settings: on, off
n
This parameter is not available for the Plug-in Parts.
From this display you can set the Send Level and Dry Level sent to the System Effects for each Part. For details
about the Effect connection in the Performance mode, see page 179.
Determines the send level for the Reverb effect of the selected Part, giving you detailed control over the Reverb
balance among the Parts.
Settings: 0~127
Determines the send level for the Chorus effect of the selected Part, giving you detailed control over the Chorus
balance among the Parts.
Settings: 0~127
Determines the level of the unprocessed (dry) sound of the selected Part, letting you control the overall effect
balance among the Parts.
Settings: 0~127
Performance Edit mode
When Offset (below) is set to 64:
127
Actual resulting
velocity (affecting the
tone generator)
When Depth (above) = 64 and Offset = 64
127
127 0
64 127
Velocity with which you play a note
Part Edit
Depth = 127
Depth = 64
Depth = 32
Depth = 0
0 127
Velocity with which you play a note
When Depth (above) = 64 and Offset = 96
127
0 64
127
[EDIT] Element selection
Owner's Manual
217