Table of Contents
Advertisement
OSCILLATING SPINDLE SANDER
ASSEMBLY AND OPERATING INSTRuCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MANuAL.
Copyright
2006 by Harbor Freight Tools
©
contained herein may be reproduced in any shape or form without the express written consent of Harbor
Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improve-
ments, actual product may differ slightly from the product described herein. Tools required for assembly
and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10f
Model
95088
. All rights reserved. No portion of this manual or any artwork
®
Advertisement
Table of Contents
Related Manuals for Central Machinery 95088
Summary of Contents for Central Machinery 95088
- Page 1 Failure to do so can result in serious injury. SAVE ThIS MANuAL. Copyright 2006 by Harbor Freight Tools © contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improve- ments, actual product may differ slightly from the product described herein.
-
Page 2: Product Specifications
Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. SKU 95088 For technical questions, please call 1-800-444-3353. 120 VAC, 60 Hz, 3.5 Amps 2,000 RPM, 5/8”... -
Page 3: Electrical Safety
Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. SKU 95088 For technical questions, please call 1-800-444-3353. ELECTRICAL SAFETY... - Page 4 When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this SKU 95088 For technical questions, please call 1-800-444-3353. TOOL uSE AND CARE...
-
Page 5: Specific Safety Rules
Maintain labels and nameplates on the Sander. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Avoid unintentional starting. Make sure you are prepared to begin work before plugging in the Sander. -
Page 6: Grounded Tools: Tools With Three Prong Plugs
Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGuRE A SKU 95088 For technical questions, please call 1-800-444-3353. GROuNDING WARNING! -
Page 7: Double Insulated Tools: Tools With Two Prong Plugs
Always replace a damaged extension cord or have it repaired by a qualified electri- cian before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. SKU 95088 For technical questions, please call 1-800-444-3353. ExTENSION CORDS Page 7... - Page 8 16.1 – 20.0 FIGuRE C * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. n 0 xxxx/min. SKU 95088 For technical questions, please call 1-800-444-3353. (120 OR 240 VOLT) ExTENSION CORD LENGTh...
- Page 9 When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. INSTALLING AND ChANGING SANDING SLEEVES WARNING! Always make sure the Power Cord (73) of the Spindle Sander is unplugged from its electrical outlet prior to making any adjustments to the tool.
-
Page 10: Operation
After you have put on the appropriate safety gear covered on page 3 of this manual, and you have installed the sanding sleeve you want to use, plug in the Sander. Turn the sander on using the Switch (80). Always run the Sander for a few seconds before contacting the work piece. -
Page 11: Parts List
6001zz 608zz Ø4 4.2 x 13 Ø4 4.2 x 110 4.2 x 22 6203zz 4.2 x 15 SKU 95088 For technical questions, please call 1-800-444-3353. PARTS LIST Ø5 Ø6 4.2 x 13 4.2 x 13 4.2 x 13 6203zz 4.2 x 19 4 x 16 4.2 x 15... - Page 12 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95088 For technical questions, please call 1-800-444-3353. PARTS LIST CONTINuED Description Q’ty...
-
Page 13: Assembly Diagram
ASSEMBLY DIAGRAM 5 (96, 97, 98, 99, 100, 101) 4 (108, 109, 110, 111,112) 3 (102, 103, 104, 105, 106, 107) 2 (113,114,115) REV 07d, 07i SKU 95088 For technical questions, please call 1-800-444-3353. Page 13... - Page 14 ASSEMBLY DIAGRAM CONTINuED SKU 95088 For technical questions, please call 1-800-444-3353. Page 14...
-
Page 15: Limited 1 Year / 90 Day Warranty
LIMITED 1 YEAR / 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.