Remove And Replace Handles; Remove Doors And Hinge; Replace Doors And Hinge; Remove And Replace Freezer Drawer - Viking VCFF136D Installation Manual

Doors & Drawer Removal

Remove and Replace Handles

Remove Doors and Hinges
1. Using a 3/32"or 1/8" hex wrench, loosen the 6. Disconnect the water line by holding the tabbed
two set screws located on the side of each
handle.
2. Pull the handle straight out from the door.
Make sure you keep the screws for reattaching 6a.Disconnect the water line by pulling back on the
the handles.
3. To replace the handles, reverse the directions.
Remove Doors and Hinges
7. Remove the parts for the top hinge as shown in
IMPORTANT:
• Remove food and any adjustable door or utility
bins from doors.
• Keep the refrigerator doors closed until you are
ready to lift them free from the cabinet.
NOTE: Provide additional support for the
8. Using a 3/8" hex wrench, remove the leveling leg
refrigerator door while the hinges are being
removed. DO NOT depend on the door gasket
magnets to hold the door in place while you are
working.
TOOLS NEEDED: 5/16", 3/8", 1/4" hex-head
socket wrench, #2 Phillips screwdriver, and a flat-
blade screwdriver.
1. Unplug refrigerator or disconnect power.
2. Remove the base grille. Grasp the grille firmly
and pull it toward you.
3. Starting with the right-hand side door, remove
the parts for the top hinge as shown in Top
Hinge graphic. Lift the refrigerator door from
the bottom hinge pin.
4. Remove the shim from the bottom hinge pin
and keep it for later use. See Bottom Hinge
graphic.
5. Remove top hinge cover from left side
refrigerator door. Disconnect the wiring plug
located on top of the hinge by wedging a flat-
blade screwdriver or your fingernail between
the two sections. See Connections graphic.
.
12
(cont.)
section of the water line while turning the black
locking collar clockwise. See Connections graphic.
OR
locking collar while pulling the water line out of
the water line connector. See Connections
graphic.
Top Hinge graphic. Lift the left-hand side door
from the bottom hinge pin.
NOTE: On some models, remove the shim from
the bottom hinge pin and keep it for later use.
See Bottom Hinge graphic.
brackets from the bottom of the cabinet. Keep
screws for later use.
Top Hinges
A
B
C
D
A. Hinge Cover Screw
B. Top Hinge Cover
C. 5 / " Hex-Head Hinge Screws
16
D. Top Hinge
Bottom Hinges
A
B
C
A. Shim (on some models)
B. Bottom Hinge
C. Hinge Screws
6 6a
Connections Connections
A
B
B
A
OR
A. Tabs
A. Wiring Plug
B. Wiring Plug
B. Water Line Connection
Door & Drawer Removal
Replace Doors and Hinges

Replace Drawer Front

1. Assemble the parts for the top hinge as shown 1. Slide the drawer glides out of the freezer
in Top Hinge graphic. DO NOT tighten the
screws completely.
2. Replace the parts for the bottom hinge as
shown in Bottom Hinge graphic. Tighten
screws. Replace the refrigerator door.
Note: Provide additional support for the 2. Pull the drawer brackets toward you to position
refrigerator door while the hinges are being
moved . DO NOT depend on the door gasket
magnets to hold the door in place while you
are working.
3. Align the door so that the bottom of the 3. Completely tighten the four screws.
refrigerator door aligns evenly with the top of
the freezer drawer. Tighten all screws.
4. Reconnect the wiring plug on top of the left-
hand side refrigerator door.
5. Reconnect the water lines by firmly pushing
one line inside the other. Slide the black
locking collar fully forward.
OR
5a.Reconnect the water line by pulling back the
locking collar ring while firmly pushing the
water line into the connector.
6. While holding the tabbed section of the
waterline, turn the locking collar
counterclockwise until you hear a "click."
Note: The arrow on the tabbed section should
align with the two bars on the locking collar.
7. Check for leaks. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT: Two people may be required to
remove and replace the freezer drawer.
Remove Drawer Front
1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer
glides to the drawer front. See Drawer Front
Removal graphic.
Note: Loosen screws three to four turns. Keep
the screws in the drawer front.
3. Lift drawer front upward and off the screws.
See Drawer Front Removal graphic.
13
(cont.)
compartment. Insert the screws in the top of
the drawer front into the slots in the drawer
brackets. See Drawer Front Replacement
graphic.
the two screws in the bottom of the drawer
front into the brackets. See Drawer Front
Replacement graphic.
Drawer Front Removal
A
A. Loosen 4 Door Bracket Screws
Drawer Front Replacement