Table of Contents
Advertisement
Insert Editing
The Insert Editing function lets you substitute a part of a
previously made recording by inserting one or several new
scenes together with new sound. This editing method lets you
precisely set the end point, and the recording will stop
automatically when this point is reached. This editing method
also ensures smooth, noise-free picture transitions between
old and new recordings.
As the Insert Editing function is mostly used for replacing
relatively short parts of an already recorded programme, no
Tape Library data is registered for the newly inserted parts.
1
4
INSERT
6
INSERT
Preparations
≥ Connect a movie camera or another VCR to this VCR as
shown in the illustration on page 32.
≥ Display the VCR picture on the TV.
≥ Insert the cassette onto which you want to perform insert
editing and make sure that its erasure prevention tab is
intact.
As soon as the cassette is inserted, the Cassette Number
Check starts. Wait a few moments until it is completed.
(See page 14.)
≥ Set the VCR/TV switch P to "VCR".
≥ Press the INPUT SELECT button 3 to select the AV input
(external input) "A1", "A2" or "A3" according to the socket(s)
to which you have connected the source unit.
A1: When connected to the AV1 21-pin Scart socket s
[AV1 (TV)]
A2: When connected to the AV2 21-pin Scart socket t
[AV2 (DECODER/EXT)]
≥ Make sure that "AV2" is set to "EXT".
(See page 46.)
A3: When connected to the Video Input socket \
[VIDEO IN (AV3)]/the S-Video Input socket [
[S-VIDEO IN (AV3)] and Audio Input sockets ]
[AUDIO IN (AV3)] on the front panel of this VCR
≥ When connecting a mono type movie camera or
VCR to this VCR's front AV sockets, connect to the L
(white) audio socket.
≥ Press the 3D DNR button f to turn 3D DNR function off so
that 3D DNR lamp is not lit, to ensure editing with optimal
picture quality.
34
2
0:00.00
3
0:00.00
Operations
1
Press the PAUSE/STILL button g on this VCR and then
use the Shuttle Ring h or Jog Dial i to search for the
tape position at which you want the insert recording to
end.
2
Press the RESET button = to reset the tape counter
displayed on the VCR display to "0:00.00".
3
Use the Shuttle Ring h or Jog Dial i to search for the
tape position at which you want the insert editing to
start.
4
Press the INSERT button ` to put this VCR in the
recording pause mode.
≥ The new sound will be recorded on the Hi-Fi sound
tracks.
≥ In case you also want to record the new sound on the
normal (mono) audio track, press the A.DUB button
a. The indication on the On Screen Display changes
to "AV INSERT".
5
Start playback on the source unit and search for the
beginning of the scene that you want to dub (copy) onto
this VCR.
6
When you have found that point, press the PAUSE/
STILL button g on this VCR again to start recording the
new part from the playback unit.
≥ When the tape counter displayed on the On Screen
Display becomes "0:00.00", recording automatically
stops, and this VCR stops in the recording pause
mode.
≥ To edit additional scenes, repeat operation steps 1 to
6.
7
Press the Stop button 9 on this VCR to finish editing.
Hint:
≥ If you want to change the audio recording level, adjust it.
(See page 20.)
Notes:
≥ Insert editing cannot be performed on blank sections of a
tape. In such case, perform assembly editing first.
(See page 32.)
≥ The cassette number is not recorded for the programme
which has been recorded with Insert Editing.
Advertisement
Table of Contents
