Related Manuals for Miele LaPerla G 2830 SCi
Summary of Contents for Miele LaPerla G 2830 SCi
-
Page 1: Operating Instructions
Operating Instructions LaPerla G 2830 SCi To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 06 696 130... -
Page 2: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS ....... . . 4 Guide to the dishwasher ..........7 Control panel . - Page 3 Contents Additional options ..........39 Delay start .
-
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING – Electrical Safety Before installation, make sure that When using your dishwasher, follow the voltage and frequency listed on basic precautions, including the the data plate correspond with the following: household electrical supply. This data must correspond to prevent injury and Read all instructions before machine damage. - Page 5 A damaged appliance cabinetry. is dangerous. Unplug the machine and Do not install this dishwasher call your Miele dealer or the Miele beneath a cooking surface, oven or Technical Service Department. any appliance that radiates heat. Ensure that any plastic wrappings, High temperatures from these units may bags, etc.
- Page 6 If the power cord is damaged it minutes before using the dishwasher. must only be replaced by a Miele This will release any accumulated Service technician with a genuine Miele hydrogen gas. Do not smoke or use an power cord.
-
Page 7: Guide To The Dishwasher
Guide to the dishwasher a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i Child Safety Lock in the door handle (not visible) d Middle spray arm j Rinse aid reservoir e Air inlet for drying k Dual compartment detergent (depending on model) -
Page 8: Control Panel
Guide to the dishwasher Control panel a K (Information) touch control e Standby indicator To display more info about the The indicator lights when the displayed menu dishwasher is turned on but the display is turned off. b s (On/Off) touch control f + C (Clear) touch control To turn the dishwasher on and off To switch back to the previous menu... -
Page 9: Display
Guide to the dishwasher Display The following can be selected in the A bullet in the display next to the touch display: control shows that a function can be selected with this control. – the wash program The arrow on the right side in the –... -
Page 10: Caring For The Environment
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source. -
Page 11: Before Using For The First Time
Before using for the first time To open the door Child Safety Lock ^ Press the release catch inside the The Child Safety Lock is designed to door grip. prevent children from opening the dishwasher. If the door is opened during operation, ^ To lock the door, push the slider the dishwasher will stop running. - Page 12 Before using for the first time Welcome screen ^ Turn the dishwasher on with the sensor s. The Welcome screen shows when the washer is turned on for the first time. Language setting The display changes automatically to the language setting. The selected language is marked with a L check.
- Page 13 Before using for the first time After confirming the minutes, a message shows confirming that the set-up of your machine has been successfully completed. Insufficient After confirming this message, the two messages salt Insufficient rinse aid may show. Confirm with and the display changes to the main menu.
-
Page 14: Water Softener
Before using for the first time Water softener Checking the water hardness The water hardness measured by the Every dishwasher is tested before sensor can be displayed. leaving the factory. Any water See "Settings J - Water hardness". remaining in the machine is from the final factory test and does not External water softener indicate that the machine has been... -
Page 15: Filling The Salt Container
Before using for the first time Filling the salt container Inadvertently filling the salt container with dishwashing detergent will damage the water softener. Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener. ^ Press the button in the direction of the arrow until the flap springs open. -
Page 16: Salt Refill Message
Before using for the first time Salt refill message ^ When the display shows Insufficient salt , refill the salt after the program has finished. ^ Confirm with The message will clear from the display. After the container has been filled, the water softener is automatically reactivated the next time the Insufficient... -
Page 17: Rinse Aid
Before using for the first time Rinse aid Adding rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. Filling the rinse aid reservoir with detergent will damage the reservoir. -
Page 18: Rinse Aid Refill Message
Before using for the first time Rinse aid refill message Insufficient rinse aid When the message first comes on, there will be enough rinse aid left for 2 - 3 washes. ^ Refill rinse aid after the program has finished. If the "2 in 1"... -
Page 19: Loading The Dishwasher
Loading the dishwasher ^ The spray arms must not be blocked Do not wash items soiled with by items that are too tall or hang ash, sand, wax, grease or paint in through the baskets. Check the dishwasher. clearance by manually rotating the Ash and sand do not dissolve and spray arms. -
Page 20: Items Not Recommended For Dishwashing
Loading the dishwasher Items not recommended for Glassware: dishwashing – There are no standard guidelines for washing glassware, when in doubt – Cutlery with wooden handles wash by hand. – Wooden cutting boards – When purchasing new dishes, – Glued items such as old knives with glasses and cutlery, make sure they handles glued together around the are dishwasher safe. -
Page 21: Split Cutlery Tray
Loading the dishwasher Split cutlery tray Spoons with thick handles may have to be placed as knives and forks with their ^ Arrange the cutlery as shown in the heads in the holders cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. -
Page 22: Upper Basket
Loading the dishwasher Upper basket Removable spike insert The spike insert can be removed to For safety reasons only use the create more space for larger items, dishwasher with the upper and lower e.g. a saucepan. basket inserted. Exception: The programs "Large items normal"... - Page 23 Loading the dishwasher Adjustable cup racks Coffee bar ^ Raise the rack to make room for tall (depending on model) glasses. Lower it to double stack Glasses can be leaned against the smaller pieces. coffee bar for a secure stand. The height of the cup rack can be adjusted in two levels.
- Page 24 Loading the dishwasher Glassware rail Multi-function basket (depending on model) The multi-function basket is designed to securely wash baby bottles, saucers The glassware rail is designed for a and small items, e.g. toys. secure stand of tall glasses and stemmed glassware. ^ Remove the spike insert on the right side of the upper basket and insert ^ Flip the bar down to lean tall glasses...
- Page 25 Loading the dishwasher To wash baby bottles ^ Insert the nipples under the hooks a. ^ Open the flaps b and insert the bottle neck into the opening. ^ Small items like the rings and caps of the bottles can be inserted in the open spaces.
-
Page 26: Adjusting The Upper Basket
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, a variety of plate dimensions The upper basket can be raised or can be accommodated. lowered to accommodate tall items. For example: If the upper basket is in The basket can also be angled to fit tall its highest position a plate with a items in both, the upper and lower... -
Page 27: Lower Basket
Loading the dishwasher Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. - Page 28 Loading the dishwasher Comfort inserts PlateGuard Plus with StemGuard The comfort inserts are designed for cups, glasses, plates, bowls, pots, etc. Removing an insert a: ^ To remove an insert, gently pull up on ^ To insert tall items, raise the cup rest. the handle.
-
Page 29: Basket Accessories
If placed anywhere else, water will not basket, b. reach all surfaces. The bottle will not be properly cleaned. Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. -
Page 30: Use
Detergent You can use powder, gel or tab detergents. Follow the dosage Dishwasher detergents contain information on the detergent irritant and corrosive ingredients. packaging. See "Settings - Detergent" Avoid inhaling or swallowing for more information on detergent dishwasher detergent. usage. Keep children away from detergent. -
Page 31: Adding Detergent
Adding detergent ^ Add detergent to compartment II and close the flap. ^ To open, press the latch on the detergent dispenser. The flap will ^ If a Pre-rinse is desired, and available spring open. for your chosen program, add 1 teaspoon (5 ml) of detergent to The flap is always open at the end of a compartment I. -
Page 32: Turning On
Turning on ^ Make sure the spray arms can rotate freely. ^ Close the door. ^ Open the water supply, if closed. ^ Turn the dishwasher on by touching the s control. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. -
Page 33: Program Guide
Program guide Program When to use Program sequence Pre- Main Interim Final Drying rinse wash rinse rinse Normal For normally soiled dishware with dried on food Run-time 131 min Pots + For normally soiled pots and pans with dried Pans on food, and heavily soiled dishware, 120% detergent recommended Run-time 129 min... - Page 34 Program guide Program When to use Program sequence Pre- Main Interim Final Drying rinse wash rinse rinse Starch For dishware with dried on starchy food; 120% detergent recommended Run-time 148 min Cheese For dishware with dried on cheese; 120% detergent recommended Run-time 150 min Sani Wash To sanitize dishware, e.g.
-
Page 35: Use
Selecting Options Options can be added to the selected program. ^ Select Options The display shows the available options for the selected program. Available options: Pre-rinse: – For easily removable soiling Soak: – To soak stubborn soiling. When using powder detergent, fill approx. 1 teaspoon (5 g) of detergent in the detergent compartment I. -
Page 36: Starting A Program
Time display You can now select the detergent Before the program starts, the time used. Availabe selections are: display shows the running time of the Powder, Gel, "2 in 1" and "3 in 1" selected program in hours and minutes. tabs. -
Page 37: At The End Of A Program
At the end of a program Interrupting a program At the end of a program the display A program is interrupted as soon as the Program finished shows door is opened. If the door is closed, the program will continue from where it Dishes tends to chip if removed still hot was interrupted. -
Page 38: Changing A Program
Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: Sensor Wash 12:00 Pre-rinse Time left 1:30 h Cancel ° ^ Select Cancel ^ Confirm the message Cancel program? with... -
Page 39: Additional Options
Additional options Delay start The start time of a program can be delayed from 15 minutes to 24 hours in 15-minute-increments. When using the "Delay Start" function, make sure that the detergent compartment is dry before adding detergent. Wipe dry with a cloth if necessary. Otherwise the detergent could stick together and not completely rinse out. - Page 40 Additional options Sensor Wash 12:00 Start at 12:00 Cancel ° The program name and the start time are displayed. The program starts automatically at the selected time. Starting a program before the delay start has elapsed: A program can be started before the delay start time has elapsed.
-
Page 41: Settings J
Settings J The "Settings J" menu allows you to adjust standard settings Open the Settings J menu ^ Turn the dishwasher on by touching the s control. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. - Page 42 Settings J Language J Time of day The display contents can be shown in The selection allows the clock to be different languages. shown as 24 or 12 hours and to set the clock. The displayed language can be changed by the submenu Setting the clock format "Language J".
- Page 43 Settings J Detergent 3 in 1 tabs To achieve the best results the used The function "3 in 1" adjusts the detergent can be set on your program cycle to the use of "3 in 1" dishwasher. The selection allows detergent products (detergent with "Powder", "Gel", "2 in 1"...
-
Page 44: Water Hardness
Settings J Water hardness Rinse aid The dishwasher is equipped with a For best results, the rinse aid dosage sensor softener, which automatically can be adjusted. detects the hardness of your tap water. The dosage can be set in steps from 0 After plumbing the dishwasher and to 6 ml. - Page 45 Settings J Reorganize program list The order of the programs in the program list can be reorganized. Frequently used programs can be saved to the first three positions. Select program for position 1 12:00 ° Normal B ° Pots + Pans °...
-
Page 46: Save Options
Settings J Save options Additional options can be selected for some programs, e.g. extended drying. See "Use - Selecting options". Save options allows you to save the selected options for future use with this program. The function is turned off by default. ^ Select the desired setting and confirm with... - Page 47 Settings J Child Safety Lock The Child Safety Lock protects the dishwasher from misuse. If the dishwasher is turned on while the Child Safety Lock is The appliance is locked activated, the display shows The lock must be deactivated before the dishwasher can be used.
- Page 48 Settings J Program lock The running program can be locked. This function prevents accidentally changing a program during use. You can select if the program lock should be activated or not. The actual locking of the program is done when a program is started.
- Page 49 Settings J Locking a program To lock a program, a program must be started first. ^ Select a program and begin it with Start Sensor Wash 12:00 Main wash Time left 1:23 h ° Cancel ° ^ Select ). ^ Select to activate this function and confirm with The program is locked.
- Page 50 Settings J Temperature Buzzer volume The temperature can be displayed in Two buzzer volumes can be selected or °C/Celsius or °F/Fahrenheit. the buzzer can be deselected. The temperatures are shown in °C/Celsius by default. The buzzer tone at the end of a ^ Select the desired temperature unit program is turned off.
-
Page 51: Keypad Tone
Settings J Keypad tone Standby A tone will sound when a control is To save energy the display is turned off touched. 10 minutes after a control is touched. The keypad tone is turned on by The standby indicator flashes. default. -
Page 52: Factory Default
Settings J Dealer Factory default All settings can be reset to factory Demo modes are only for default. showrooms. ^ Confirm the message Reset to The dishwasher has three demo factory default? with programs for showrooms. ^ Confirm the information All settings The programs "Demo mode"... -
Page 53: Frequently Asked Questions
– Select the desired program. Start – Select If the problem persists, call Technical Service. The buzzer sounds. The The waterproof system – Turn off the water display shows the has activated. supply. following: – Call Miele Technical Fault Waterproof F70 Service. -
Page 54: Problems Water Intake/Drain
Frequently asked questions Problems water intake/drain Issue Possible fault Solution The buzzer sounds. The display shows the following: No water intake The water supply is Open the water supply all the Open the water faucet closed. way. Fault water intake FXX Before fixing the fault: –... - Page 55 Frequently asked questions Issue Possible fault Solution The program "Energy The intake water does not – Restart the program. Saver" displays the have a minimum – If the fault is displayed fault: temperature of 115°F again, use a different Water intake temp. too (45°C).
-
Page 56: General Problems With The Dishwasher
Frequently asked questions General problems with the dishwasher Issue Possible fault Solution The display remains The display has gone Touch any control. See "Settings J - Standby" for off. into "Standby" mode to save energy. more info. The buzzer sounds The salt container lid –... - Page 57 Frequently asked questions Issue Possible fault Solution Detergent is left in the The dispenser was damp Dry the dispenser before dispenser at the end of a when detergent was adding detergent. program. added. The detergent lid cannot Detergent residue is Remove the residue.
-
Page 58: Sounds
Frequently asked questions Sounds Issue Possible fault Solution There is a knocking The spray arm is hitting an Interrupt the program, noise in the wash item in the basket. rearrange the items cabinet. blocking the spray arm. There is a rattling Items are not secure in the Interrupt the program and wash cabinet. -
Page 59: Poor Cleaning Results
Frequently asked questions Poor cleaning results Issue Possible fault Solution The dishes are not The dishes were not loaded See "Loading the clean. correctly. dishwasher". The program was not Select a more intensive powerful enough. program, see "Program Guide". Stubborn but normal soiling Use the function "Adjust (e.g. - Page 60 Unsuitable "2 in 1" or "3 in 1" Use a different detergent. can be wiped off. products were used. Try normal tabs or powder detergent. The automatic water Call Miele Technical Service. softener unit is defective.
- Page 61 Frequently asked questions Issue Possible fault Solution Glasses are Detergent deposits. Use a different detergent. discolored and the film cannot be wiped off. Glasses are dull and Glasses are not There is no remedy. Only discolored and film dishwasher safe. wash dishwasher safe cannot be wiped off.
-
Page 62: After Sales Service
Miele products will not be recognized cycles a service technician will be able by Miele. Our goal is to prevent to input these into your machine unauthorized (and untrained) service controls via the indicator light marked personnel from working on your Miele PC. -
Page 63: Transport
Transport To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. -
Page 65: User Maintenance Instructions
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use. -
Page 66: Cleaning And Care
The wash cabinet can be cleaned with wiped with a damp cloth or suitable a dishwasher cleaner such as "Dis cleaning agent designed for use on Cleaner" available from your Miele plastic. dealer, Miele or online at ^ For stainless steel panels see www.store.miele.com. -
Page 67: Triple Filter System
Cleaning and Care Triple filter system Cleaning the triple filter ^ Turn off the dishwasher before The triple filter system in the base of the wash cabinet prevents food from being cleaning. redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. - Page 68 Cleaning and Care ^ Return the filter so it lies flat in the To clean the underside of the filter the base of the wash cabinet. flap must be opened. ^ Lock the filter by turning the handle ^ Push the clips together a and open the flap b.
-
Page 69: Cleaning The Spray Arms
Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). -
Page 70: Cleaning The Water Inlet Filter
^ Reinsert the filter and seal. Make sure the water valve and the intake hose connection is recommended. These they are seated correctly. filters can be purchased from Miele. ^ Screw the intake hose back on the water valve, checking that it is not Cleaning the filter cross-threaded. -
Page 71: Cleaning The Drain Pump And Non-Return Valve
Cleaning and Care Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. -
Page 73: Installation Instructions
Installation Instructions For installation of the dishwasher please refer to the Installation Sheet supplied with these instructions. -
Page 74: Help To Protect The Environment
Help to protect the environment Disposal of the packing Disposal of an old machine material Old appliances may contain materials that can be recycled. Please contact The cardboard box and packaging your local recycling authority about the protect the appliance during shipping. possibility of recycling these materials. -
Page 75: Electrical Connection
V 1-800-565-6435 right side of the door. A damaged power cord must only Specifications be replaced with a genuine Miele The dishwasher comes equipped with a cord by a Miele service technician. 4 ft (1.2 m) power cord with a molded... -
Page 76: Plumbing
Plumbing Connection to the water supply – The water inlet hose comes equipped with a 3/4" female hose Do not drink water from the thread connector. This can be dishwasher! directly connected to a water supply with 3/4" MHT (male hose thread –... -
Page 77: Drainage
7/8" (22 mm). remove the lower basket. – Drain hose extensions and adapters ^ Pull the lower spray arm firmly can be ordered from Miele. The maximum drain hose length is upwards to remove. 13 ft. (4 m), max. drain height: 39"... - Page 80 Alterations reserved/5006 M.-Nr. 06 696 130 / 02 G 2830 SCi / en - US...