Picture Adjustment; Time Setting; Sound Adjustment - LG Colour television Owner's Manual

Picture adjustment

Note: Picture menu options are not available for
the RGB input source.
PSM (Picture Status Memory)
The picture Dynamic , Standard
Game are programmed for good picture repro-
duction at the factory and cannot be changed.
XD
You can enjoy the vivid and hi-definition picture with
LG's excellent Digital Reality processor technology.
Eye (option)
When the eye function is on, the most suitable pic-
ture is automatically adjusted according to the sur-
rounding conditions.
At this time the display
appear continuously but the display
appears each time the picture condition changes.
Note:a.The eye function is automatically switched off.
b.EYE function is not available for RGB input source.
SSM (Sound Status Memory)
Sound Frequency Adjustment
Press the G G button in User
User sub menu.
The sound Flat , Music , Movie
programmed for good sound reproduction at the
factory and cannot be changed.
Turbo sound selection
When this function is on, the sound will be more
emphasized and amplified than normal sound.

Sound adjustment

You can adjust balance, AVL (Auto Volume
Leveler), AVL automatically keeps on an equal
volume level even if you change programmes.
The Turbo sound creates an all around sound as
in a concert hall.
X-WAVE (Wireless Sound) (option)
You can also listen to the sound through the FM
receiver.
Note:
a. If the reception is poor or weak, select a dif-
ferent frequency.
b. For best results, there should be no more than
5m (16.4ft) between the TV and FM Receiver.
c. In certain areas, the FM transmitter ability may
be weak, such as near a broadcast tower.
d. The reception sensitivity may depend on the
kinds of receiver(FM radio).
Sound output selection
In AV mode, you can select output sound for the
left and right loudspeakers.
Repeatedly press the I/II/
*
sound output.
L+R :Audio signal from audio L input is sent to left
loud-speaker and audio signal from audio R
input is sent to right loud-speaker.
L+L :Audio signal from audio L input is sent to left
and right loud-speakers.
R+R :Audio signal from audio R input is sent to
left and right loud-speakers.
Stereo/Dual reception
When a programme is selected, the sound infor-
6
Setting the On/Off timer
By using this function, the set automatically
switches on or off at a preset time. You must set
, Mild and
the time correctly before using the on/off time
function.
Note :
a.
b. To view the remaining on/off time, select the
c. When you switch the main power off, the
Auto sleep
in green does not
in yellow If you select
menu, the set will automatically switch itself to
standby mode approximately ten minutes after a
TV station stops broadcasting.
Sound adjustment
mation for the station appears after the pro-
gramme number and station name disappear.
to display the
and Sports are
Mono sound selection
In stereo reception if the stereo signal is weak,
you can switch to mono by pressing the I/II/
ton twice. In mono reception the depth of sound is
improved. To switch back to stereo, press the
I/II/
Language selection for dual language broadcast
If a programme is received in two languages (dual
language), you can switch to
DUAL I+II
DUAL I
the loudspeakers.
DUAL II
guage to the loudspeakers.
DUAL I+II
loudspeaker.
NICAM reception (option)
If your set is equipped with the receiver for NICAM
reception,
Instantaneous Companding Audio Multiplex) digi-
tal sound can be received.
Sound output can be selected according to the
type of received broadcast by pressing the I/II/
button to select the
button repeatedly.
1. When NICAM mono is received, you can
2. When NICAM stereo is received, you can
3. When NICAM dual is received, you can select

Time Setting

On time works only in standby mode.
Time menu.
Clock is reset .
On on the Auto sleep
Broadcast On Screen Display
Mono
MONO
Stereo STEREO
Dual DUAL I
button twice again.
*
DUAL I
by pressing the I/II/
sends the primary broadcast language to
sends the secondary broadcast lan-
sends a separate language to each
the high quality
select NICAM MONO or FM MONO.
select NICAM STEREO or FM MONO. If the
stereo signal is weak, switch to FM mono.
NICAM DUAL I , NICAM DUAL II
NICAM DUAL I+II or MONO
mono is selected the display
on the screen.
pull-down
but-
*
, DUAL II or
button repeatedly.
*
NICAM (Near
*
or
. When FM
MONO appears