Level Range - KitchenAid KDRS807SSS04 Installation Instructions Manual

30" (76.2 cm) freestanding and slide-in dual fuel ranges
Table of Contents

Advertisement

Available languages

Available languages

Check
Operation
of Cooktop
Burners
Standard Surface
Burners
Push in and turn each control knob to the "LITE" position.
The flame should light within 4 seconds. The first time a burner is
lit it may take longer that 4 seconds to light because of air in the
gas line.
TripleTier_ Flame Burner
To start simmer burner:
Push in and turn control knob to "LITE."
The flame should light within 4 seconds. The first time a burner is
lit it may take longer that 4 seconds to light because of air in the
gas line.
To start power burner:
Push in control knob again and turn to "POWER BURNER HI" to
light the outer burner.
The flame should light within 4 seconds. The first time a burner is
lit it may take longer that 4 seconds to light because of air in the
gas line.
If burners
de net light properly:
Turn cooktop control knob to the "OFF" position.
Check that the range is plugged in and the circuit breaker has
not tripped or the household fuse has not blown.
Check that the gas shutoff valves are set to the "open"
position.
Check that burner caps are properly positioned on burner
bases.
If the "low" flame needs to be adjusted:
1. Remove the control knob.
2. Hold the knob stem with a pair of pliers. Use a small flat-
blade screwdriver to turn the screw located in the center of
the control knob stem until the flame is the proper size.
3. Replace the control knob.
4. Test the flame by turning the control from "LO" to "HI,"
checking the flame at each setting.
To adjust TripleTier ® Flame burner:
1. Remove the control knob.
2. Insert a flat-blade screwdriver into adjustment
locations
shown in the following illustration and engage the slotted
screw. Turn the screw until the flame is the proper size.
A. Simmer burner regulation
B. Power burner regulation
3. Replace the control knob.
4. Test the flame by turning the control from "LO" to "HI,"
checking the flame at each setting.
Repeat start-up. If a burner does not light at this point, turn
control knobs to "Off" and contact your dealer or authorized
Replace oven racks in oven cavity. Replace warming drawer or
service company for assistance,
storage drawer.
Adjust Flame Height
To Replace Warming
Drawer:
1. Align the drawer glides with the receiving guides.
Adjust the height of top burner flames. The cooktop "low" burner
flame should be a steady blue flame approximately
1¼.(0.64 cm)
high.
A
_
__
kf
2. Push drawer in all the way.
Gently open and close the drawer to ensure it is seated properly
on the slides.
A. Low flame
B. High flame
To adjust standard burners:
The flame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
A s
A. Valvestem
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check that range level. See "Level Range."
5. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by protective shipping
material. Dry thoroughly with a soft cloth. For more
information, see the "Range Care" section of the Use and
Care Guide.
6. Read "Range Use" in the Use and Care Guide.
7. Turn on surface burners and oven. See the Use and Care
Guide for specific instruction
on range operation.
18

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Kdss907sss04Ykdss907ss02

Table of Contents