Table of Contents
Advertisement
Available languages
Available languages
Installation
t
[] Remove the top wood sheet from
over the top of the cooktop.
_ Remove the shipping brackets and
discard.
Excessive
Weight Hazard
Use two or more people to move
and install cooktop.
Failure to do so can result in back
or other injury.
= Carefully lift the cooktop up and set
aside. Write down the model and serial
numbers before installing the cooktop.
Both numbers are on the model/serial
number plate located on left front
underside of the burner box.
_ Unpack the burner grates, burner
caps, simmer plate, grille grate, drip tray,
spill guard, wave tray, wave plate, tile
bezels, regulator, backguard and island
trim. items are either packaged under the
cooktop or on the cooktop. Parts shipped
with cooktop depend on model ordered.
= The pressure regulator and flexible,
stainless steel gas supply line connector
can be assembled to the cooktop now or
after the cooktop is installed in the cutout.
To assemble now, stand the cooktop on its
side or back surface and complete this
part of the pressure regulator/gas line
connector assembly.
To connect the flexible, stainless steel
connector to the pressure regulator
requires a 1/2" nipple.
Install the pressure regulator with the
arrow pointing up toward the bottom of the
burner box and in a position where you
can reach the regulator cap.
iMPORTANT: All connections must be
wrench-tightened. Do not make
connections to the gas regulator too tight.
Making the connection too tight may crack
the regulator and cause a gas leak. Do not
allow the regulator to turn on the pipe
when tightening fittings.
Use only pipe-joint compound made for
use with Natural and L.R gas. Do not use
teflon tape. You will need to determine the
fittings required depending on your
installation.
° 48"(121.gcm)models w ithbothgrille and
griddle
donot usescrew A
,, 36" (91.4 cm)
models w ith
griddle
donotuse
screw
B
• All other models use all 3 front screws
.3 rear screws required bet not shown on 48"
(121.g cm) models and 2 rear screwsrequired
but net shown on 36" (91.4 cm) models
attaching the
backgoard
,, 48" (121.9 cm) models with both grille and
griddle use screws at D and E
• All other models use screws at C and E
c
attaching the
island trim
[] Attach the backguard or island trim
as required for your installation. Attachment
screws are in the literature package.
_ Carefully lift and place the cooktop
into the front area of the cutout. Be
careful not to pinch the power supply cord
or damage the pressure regulator/flexible
gas supply line connector if installed. DO
NOT place all the way back into cutout.
[] Place cooktop completely into
cutout. NOTE: The cooktop must be level
for best cooking performance.
[] If the pressure
regulator
and
flexible,
stainless
steel gas supply
were
not assembled
in Step 3,
complete
the assembly
now. The
pressure
regulator
MUST be installed
with arrow on the regulator
pointing up
toward the burner box.
0
[] Connect flexible, stainless steel
gas supply connector to the rigid gas
supply line. Do not kink the connector. You
will need to determine fittings required
depending on your installation.
shuteff valve _
"open" p0sitioe
/_
gas supply..
_----'_"1._'!
_r_
/
_
to cooktop
11
•Openshutoffvalveinthegas
supply line. Wait a few minutes for gas to
move through the gas line.
t2
[] Leak testing of the appliance
shall be conducted according to the
following instructions:
Test all connections by brushing on an
approved non-corrosive leak-detection
solution. Bubbles will show a leak. Correct
any leak found.
ignitor
burner cap
electrode
"_'-_
burner
base
/
gas tube "
opening
3
[] Put burner caps on each burner
base. Place burner grates over burner
bases and caps.
if your model has only surface burners
(no grille or griddle), go to "Check the
operation of the surface burners, grille
and griddle."
4
[] If your model was shipped with
a grille or griddle, go to "Installing the
grille or griddle" to complete the
instaJlation.
Advertisement
Table of Contents
